Which NetApp HCI component communicates with activeiq.solidfire.com and the Cloud Data Services portal?

the NetApp Element software vSphere plug-in

the NetApp Element software Management Interface

A customer is trying to enable NVMe and wants to use the FC adapters in the controllers but cannot enable the protocol. Referring to the exhibit, what is causing the problem?

There are no FC adapters installed with a physical protocol set to NVMe.

There are no FC adapters installed with the speed set to 32Gbps.

There are no FC adapters installed with a physical protocol set to NVMe.

There are no FC adapters installed with a max-speed of 32Gbps.

There are no FC adapters installed with a media type of NVMe.

Your customer's MetroCluster has generated a "DISK REDUNDANCY FAILED" message.Netapp-EmA:Tue Jan 14 04:12:12 CET [netapp-EmA:cf.rv.notConnected:error]: HA interconnect: Connection for 'cfo_rv' failed.Tue Jan 14 04:12:13 CET [netapp-EmA:rv.connection.torndown:info]: HA interconnect: cfo_rv1 is torn down on NIC 1.Tue Jan 14 04:12:13 CET [netapp-EmA:cf.rv.notConnected:error]: HA interconnect: Connection for 'cfo_rv'1 failed.Tue Jan 14 04:12:15 CET [netapp-EmA:rv.connection.torndown:info]: HA interconnect: cfo_rv2 is torn down on NIC 1.Tue Jan 14 04:12:18 CET [netapp-EmA:cf.rv.notConnected:error]: HA interconnect: Connection for 'cfo_rv'2 failed.Tue Jan 14 04:12:19 CET [netapp-EmA:bridge.removed:info]: FC-to_SAS bridge siteB_2:13.126L0 [ATTO FibreBridge6500N 1.61] S/N [FB7500N111161] was removedTue Jan 14 04:12:19 CET [netapp-EmA:bridge.removed:info]: FC-to_SAS bridge siteB_2:5.126L0 [ATTO FibreBridge6500N 1.61] S/N [FB7500N111160] was removedNetapp-EmB:Tue Jan 14 04:12:12 CET [netapp-EmB:cf.rv.notConnected:error]: HA interconnect: Connection for 'cfo_rv' failed.Tue Jan 14 04:12:12 CET [netapp-EmB:rv.connection.torndown:info]: HA interconnect: cfo_rv2 is torn down on NIC 1.Tue Jan 14 04:12:13 CET [netapp-EmB:rv.connection.torndown:info]: HA interconnect: cfo_rv1 is torn down on NIC 1.Tue Jan 14 04:12:13 CET [netapp-EmB:cf.rv.notConnected:error]: HA interconnect: Connection for 'cfo_rv'1 failed.Tue Jan 14 04:12:18 CET [netapp-EmB:cf.rv.notConnected:error]: HA interconnect: Connection for 'cfo_rv'2 failed.Tue Jan 14 04:12:19 CET [netapp-EmB:bridge.removed:info]: FC-to_SAS bridge siteA_2:13.126L0 [ATTO FibreBridge6500N 1.61] S/N [FB7500N111167] was removedTue Jan 14 04:12:19 CET [netapp-EmB:bridge.removed:info]: FC-to_SAS bridge siteA_2:5.126L0 [ATTO FibreBridge6500N 1.61] S/N [FB7500N111164] was removed Referring to the messages shown in the exhibit for each node, which component is causing the problem?

the ISL between siteA and site B

You want to update your storage system and are concerned about the compatibility of the SAN components and the host environment. In this scenario, which two actions should you take to verify compatibility? (Choose two.)

Use the Interoperability Matrix Tool.

Use the Active IQ Config Advisor.

Use the Interoperability Matrix Tool.

Upload AutoSupports to Active IQ.

Use the Active IQ Config Advisor.

After a network card was replaced in an ONTAP node, you see the output shown in the exhibit. What is the problem?

One physical interface is mis-cabled.

The interface group is configured in single mode.

One physical port is not cabled.

One physical interface is broken.

One physical interface is mis-cabled.

You perform a security trace when troubleshooting a data access problem for a user. The results are shown in the exhibit. What should you do to solve this issue?

Grant the user Read Attributes access to the path.

Add the user to the BUILTIN\power Users group.

Add the user to the BUILTIN\Users group.

Grant the user Execute access to the path.

A customer is showing disk utilization is at 100% in Active IQ even though there are low protocol operations on the controller. You review the data shown in the exhibit. In this situation, what should you do?

Add disks to the aggregate to bring down the average utilization.

You receive the error shown below on a FAS2750 HA pair.Mon Jun 24 00:27:30 UTC [NetappA: scsi_cmdblk_strthr_admin: scsi.cmd.checkCondition:error]: Unknown device 0a.00.99: Check Condition: CDB 0x12: Sense Data SCSI:hardware error (0x4 - 0x44 0x0 0x0) (0).The system is cabled as shown in the exhibit. What should you do to clear the error?

Replace the controller of controller A.

Replace the cable connected to controller A's 0a port.

Replace the controller of controller B.

Replace the controller of controller A.

Re-cable the system per the FAS2750 installation guide.

For testing purposes, your customer decides to use FC on a single-node ONTAP cluster. There is only one host that the customer expects to use. High availability is not a concern for this test. The customer connects the host directly to the ONTAP node. The LUN is set up, and the igroup is configured. When the customer tries to attach to the LUN from the host, the LUN is not seen by the host.Which statement is correct in this scenario?

NPV must be enabled on the host before trying to attach to the LUN.

Multipathing must be used and connected to another FC path.

NPV must be enabled on the host before trying to attach to the LUN.

NPIV must be enabled on the host before trying to attach to the LUN.

An FC switch must be used with ONTAP.

A user can read and write some files on an NFS volume, but the user is unable to read all of the files in the volume.In this scenario, which command will help you troubleshoot this problem?

vserver security trace filter create

vserver export-policy check-access

Network Appliance NS0-194 Practice Test 2 - Free Online Exam Prep & Questions

What are two reasons to use HTTPS as the transport method for AutoSupport delivery for Active IQ?

(Choose two.)

Become a Premium Member for full access

Unlock Premium Member

Network Appliance NS0-194 Practice Test 2

Question

Network Appliance NS0-194 Practice Tests

Practice Tests