Home

Home / Cisco / 300-515

Question list

List of questions

Question 1

(0)

Which utility can you use to validate an LSP in an MPLS environment?

Question 2

(0)

What is the primary function of a VRF on a router?

Question 3

(0)

Which two statements describe primary differences between MPLS Layer 2 and Layer 3 VPNs? (Choose two.)

Question 4

(0)

Refer to the exhibit. A network engineer has been called to configure the four PE devices in order to enable full communication among the four CE devices connected to them. While starting to

Question 5

(0)

Refer to the exhibit. If the two devices are operating normally, which two conclusions can you draw from this configuration? (Choose two.)

Question 6

(0)

Which two frames can be configured on an Ethernet flow point? (Choose two.)

Question 7

(0)

In an Ethernet Virtual Circuit environment, which restriction do bridge domains have when STP is running?

Question 8

(0)

Refer to the exhibit. An engineer is implementing an MPLS P2MP TE solution. Which type of router can serve as the midpoint router and the tailend router in this P2MP TE network implementatio

Question 9

(0)

An engineer is investigating an EVPN traffic flow issue. Which type of traffic should the engineer allow in an EVPN Tree Service in order to fix this issue?

Question 10

(0)

An engineer is investigating an MPLS LDP issue. Which command should an engineer use on a Cisco IOS XE device to display the contents of the LFIB?

Open VPLUS File

Convert VPLUS to PDF

Related questions

You try to configure MPLS VPN VRF Selection based on a source IP address on an interface that has VRF configured, but you receive an error. Which action must you take to correct the problem?

Refer to the exhibit. PE1 and PE2 are exchanging VPNv4 routes for CE1 and CE2, and PE3 contains the default route to the internet. If the three devices are operating normally, which two conclusions describe this configuration? (Choose two.)

Refer to the exhibit. Which result occurs when PE1 learns a new MAC address and all three PEs are enabled with EVPN native?

A network architect is troubleshooting the L2TPv3 tunneling security due to the untrusted nature of the underlaying network. Which two L2TPv3 features does the architect deploy to address the ongoing issues? (Choose two.)

An engineer is troubleshooting AToM on an IOS XE router and receives an error when creating the xconnect. Which command does he need to complete to create the xconnect in AToM?

An engineer needs to improve MPLS network management by implementing a set of tools to support the NOC engineers in troubleshooting network failures. Which feature should the engineer implement to check the connectivity of the MPLS LSP between the ingress and egress PE routers?

Which two frames can be configured on an Ethernet flow point? (Choose two.)

In an Ethernet Virtual Circuit environment, which restriction do bridge domains have when STP is running?

You are writing the requirements for an MPLS L3VPN environment that uses MP-BGP between PE routers. In this environment, route targets and route distinguishers need to be advertised between the PE routers. Which three operations meet these requirements? (Choose three.)

Refer to the exhibit. Which statement describes the result of this BGP configuration?

Question 53 - 300-515 discussion

Report

Refer to the exhibit. Which statement describes the result of this BGP configuration?

A.

R1 operates using IPv4 and VPNv4 address families.

B.

R1 operates on IPv6 only because the bgp default ipv4-unicast command is missing.

C.

R1 establishes a VPNv4 eBGP relationship with neighbor 192.168.1.1.

D.

R1 establishes an iBGP relationship with peer 192.168.1.1.

Show Answer

asked 07/10/2024

Lance Herbst

41 questions

User

Your answer: A B C D

0 comments

Sorted by

Leave a comment first