ExamGecko
Search Search Login
Home Home / Huawei / H12-261
Question list
Search
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Which of the following AS-paths can be matched by the AS-Path filter configured using the ip as-path-filter 1 permit ^12.*74$ command?
The default SSM group address range is 232.0.0.0/8. Which of the following configurations can be performed to modify the SSM group address range?
In the aggregate ipv4-address {mask | mask-length} [as-set | attribute-policy route-policy-name1 | detail-suppressed | origin-policy route-policy-name2 | suppress-policy route-policy-name3] command, multiple parameters can be used to affect the BGP summarized route and summarization result. Which of the following statements regarding this command are true?
For Huawei S series switches, to control which member switch becomes the master switch of a stack, first power on the switch you wish to be the master switch, and then wait 20 seconds before powering on the other member switches.
Which of the following statements regarding the packet processing method in the MPLS network model are false?
Which of the following statements is true according to the topology shown?
Which of the following command outputs indicates that a loop has occurred on a switch?
OSPF has been configured on R1 as shown above, but R1 does not learn the routes from any other routers, which of the following are possible causes? (Choose all that apply.)
To reduce the amount of OSPF data and routing information in some areas, OSPF has special area types. Which of the following statements regarding OSPF special areas is true?
The output of the display in vpn-instance verbose command for displaying detailed information about all VPN instances on a network device is as follows. Which of the following statements are false?

Question 65 - H12-261 discussion

Report
Export

Which of the following statements regarding LACP are true?

A.
You can run the following commands to delete member interfaces from an Eth-Trunk:interface GigabitEthernet0/0/1shutdowninterface GigabitEthernet0/0/1 undo eth-trunk 1 interface GigabitEthernet0/0/1 undo shutdown
Answers
A.
You can run the following commands to delete member interfaces from an Eth-Trunk:interface GigabitEthernet0/0/1shutdowninterface GigabitEthernet0/0/1 undo eth-trunk 1 interface GigabitEthernet0/0/1 undo shutdown
B.
You can run the following commands to prevent frequent flapping due to physical link faults on an Eth-Trunk:interface eth-trunk 1 lacp preempt enable lacp preempt delay delay-time
Answers
B.
You can run the following commands to prevent frequent flapping due to physical link faults on an Eth-Trunk:interface eth-trunk 1 lacp preempt enable lacp preempt delay delay-time
C.
You can run the following commands to add member interfaces to an Eth-Trunk:interface GigabitEthernet0/0/1 shutdown interface eth-trunk 1trunkport GigabitEthernet0/0/1 interface GigabitEthernet0/0/1 undo shutdown
Answers
C.
You can run the following commands to add member interfaces to an Eth-Trunk:interface GigabitEthernet0/0/1 shutdown interface eth-trunk 1trunkport GigabitEthernet0/0/1 interface GigabitEthernet0/0/1 undo shutdown
D.
You can run the following commands to enable load balancing based on source IP addresses for an Eth-Trunk:interface eth-trunk 1 load-balance src-dst-ip
Answers
D.
You can run the following commands to enable load balancing based on source IP addresses for an Eth-Trunk:interface eth-trunk 1 load-balance src-dst-ip
Suggested answer: A
Show Answer
asked 18/09/2024
Oleksandr Kondratchuk
33 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms