ExamGecko
Search Search Login
Home Home / Huawei / H12-261
Question list
Search
Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Which of the following AS-paths can be matched by the AS-Path filter configured using the ip as-path-filter 1 permit ^12.*74$ command?
Which of the following command outputs indicates that a loop has occurred on a switch?
The default SSM group address range is 232.0.0.0/8. Which of the following configurations can be performed to modify the SSM group address range?
In the aggregate ipv4-address {mask | mask-length} [as-set | attribute-policy route-policy-name1 | detail-suppressed | origin-policy route-policy-name2 | suppress-policy route-policy-name3] command, multiple parameters can be used to affect the BGP summarized route and summarization result. Which of the following statements regarding this command are true?
For Huawei S series switches, to control which member switch becomes the master switch of a stack, first power on the switch you wish to be the master switch, and then wait 20 seconds before powering on the other member switches.
Which of the following statements regarding the packet processing method in the MPLS network model are false?
Which of the following statements is true according to the topology shown?
OSPF has been configured on R1 as shown above, but R1 does not learn the routes from any other routers, which of the following are possible causes? (Choose all that apply.)
To reduce the amount of OSPF data and routing information in some areas, OSPF has special area types. Which of the following statements regarding OSPF special areas is true?
The output of the display in vpn-instance verbose command for displaying detailed information about all VPN instances on a network device is as follows. Which of the following statements are false?

Question 216 - H12-261 discussion

Report
Export

A router is connected to two EBGP peers through two parallel serial cables. What method can be used to achieve bidirectional load balancing between the

EBGP peers?

A.
Run the ebgp-load-balance command on the EBGP peers.
Answers
A.
Run the ebgp-load-balance command on the EBGP peers.
B.
No method is needed. BGP automatically implements load balancing among different Ass through available links.
Answers
B.
No method is needed. BGP automatically implements load balancing among different Ass through available links.
C.
Establish an EBGP peer relationship through loopback interfaces, and configure the loopback interfaces as update sources. In each AS, import two equal-cost routes to the loopback interface of each EBGP peer to the IGP process. Inaddition, run the ebgp-max-hop and next-hop-local commands.
Answers
C.
Establish an EBGP peer relationship through loopback interfaces, and configure the loopback interfaces as update sources. In each AS, import two equal-cost routes to the loopback interface of each EBGP peer to the IGP process. Inaddition, run the ebgp-max-hop and next-hop-local commands.
D.
Configure an EBGP peer relationship through loopback interfaces, and configure the loopback interfaces as update sources. In each AS, enable two equal-cost routes to the loopback interface on each EBGP peer in the IGP process. Inaddition, run the next-hop-local command.
Answers
D.
Configure an EBGP peer relationship through loopback interfaces, and configure the loopback interfaces as update sources. In each AS, enable two equal-cost routes to the loopback interface on each EBGP peer in the IGP process. Inaddition, run the next-hop-local command.
Suggested answer: C
Show Answer
asked 18/09/2024
Fatawu Musah
31 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms