Home

Home / Juniper / JN0-649

Question list

List of questions

Question 1

(0)

You are troubleshooting a BGP connection. Referring to the exhibit, which two statements are correct? (Choose two.)

Question 2

(0)

Referring to the exhibit, anycast RP is implemented to ensure multicast service availability. The source is currently sending multicast traffic using group 239.1.1.1 and R3 is receiving PIM register

Question 3

(0)

You are asked to establish interface level authentication for users connecting to your network. You must ensure that only corporate devices, identified by MAC addresses, are allowed to connect and a

Question 4

(0)

Referring to the exhibit, which LSA type is used to advertise 192.168.1.0/24 to R5?

Question 5

(0)

You enable the Multiple VLAN Registration Protocol (MVRP) to automate the creation and management of virtual LANs. Which statement is correct in this scenario?

Question 6

(0)

Which address range is used for source-specific multicast?

Question 7

(0)

Which three configuration parameters must match on all switches within the same MSTP region? (Choose three.)

Question 8

(0)

Which two statements are correct about the deployment of EVPN-VXLAN on QFX Series devices? (Choose two.)

Question 9

(0)

Your enterprise network is running BGP VPNs to support multitenancy. Some of the devices with which you peer BGP do not support the VPN NLRI. You must ensure that you do not send BGP VPN routes to t

Question 10

(0)

You want to create an OSPF area that only contains intra-area route information in the form of Type 1 and Type 2 LSAs. In this scenario, which area is needed to accomplish this task?

Open VPLUS File

Convert VPLUS to PDF

Related questions

Your network is multihomed to two ISPs. The BGP sessions are established; however, the ISP peers are not receiving any routes. Which two statements are correct about troubleshooting your configuration? (Choose two.)

Which address range is used for source-specific multicast?

Referring to the exhibit, traffic ingresses on interface ge-0/0/3 and egresses on interface ge-0/0/4. Which queue does traffic with the IP precedence value of 100 use?

Referring to the exhibit, which two statements are correct? (Choose two.)

BGP multipath or multihop are not configured in your network. In this scenario, what is the correct sequence for BGP active route selection?

The connection between DC1 and DC2 is routed as shown in the exhibit. In this scenario, which statement is correct?

Which three configuration parameters must match on all switches within the same MSTP region? (Choose three.)

Which three MSTP parameters must match on all switches in the same MST region? (Choose three.)

Your enterprise network is running BGP VPNs to support multitenancy. Some of the devices with which you peer BGP do not support the VPN NLRI. You must ensure that you do not send BGP VPN routes to the remote peer. Which two configuration steps will satisfy this requirement? (Choose two.)

You are asked to establish interface level authentication for users connecting to your network. You must ensure that only corporate devices, identified by MAC addresses, are allowed to connect and authenticate. Authentication must be handled by a centralized server to increase scalability. Which authentication method would satisfy this requirement?

Question 53 - JN0-649 discussion

Report

Referring to the exhibit, which two statements are correct? (Choose two.)

A.

The maximum wattage that this switch can allocate to attached Ethernet devices is 100 watts.

B.

If the total power consumption exceeds 90 watts, the ge-0/0/11 interface will continue to receive power.

C.

PoE is not enabled on the ge-0/0/0 interface.

D.

The ge-0/0/10 interface supports PoE+.

Show Answer

asked 18/09/2024

Bouchtig, Yassine

40 questions

User

Your answer: A B C D

0 comments

Sorted by

Leave a comment first