How does the Traceflow tool identify issues in a network?

Injects synthetic traffic into the data plane and observes the results in the control plane.

Compares intended network state in the control plane with Tunnel End Point (TEP) keepalives in the data plane.

Compares the management plane configuration states containing control plane traffic and error reporting from transport node agents.

Injects ICMP traffic into the data plane and observes the results in the control plane.

Injects synthetic traffic into the data plane and observes the results in the control plane.

When a stateful service is enabled for the first time on a Tier-0 Gateway, what happens on the NSX Edge node?

SR is instantiated and automatically connected with DR.

DR is instantiated and automatically connected with SR.

SR is instantiated and automatically connected with DR.

SR and DR doesn't need to be connected to provide any stateful services.

SR and DR is instantiated but requires manual connection.

Which command on ESXi is used to verify the Local Control Plane connectivity with Central Control Plane?

esxcli network ip connection list | grep netcpa

esxcli network ip connection list | grep ccpd

esxcli network ip connection list | grep 1234

esxcli network ip connection list | grep 1235

Which two statements describe the characteristics of an Edge Cluster in NSX? (Choose two.)

Can contain multiple types of edge nodes (VM or bare metal)

Can have a maximum of 8 edge nodes

Must have only active-active edge nodes

Can contain multiple types of edge nodes (VM or bare metal)

Must contain only one type of edge nodes (VM or bare metal)

Can have a maximum of 10 edge nodes

Can have a maximum of 8 edge nodes

An NSX administrator is using ping to check connectivity between VM1 running on ESXi1 to VM2 running on ESXi2. The ping tests fail. The administrator knows the maximum transmission unit size on the physical switch is 1600.Which command does the administrator use to check the VMware kernel ports for tunnel end point communication?

vmkping ++netstack=geneve -d -s 1572 <destination IP address>

vmkping ++netstack=vxlan -d -s 1572 <destination IP address>

esxcli network diag ping --H <destination IP address>

esxcli network diag ping -I vmk0 -H <destination IP address>

A customer has a network where BGP has been enabled and the BGP neighbor is configured on the Tier-0 Gateway. An NSX administrator used the get gateways command to retrieve this information: Which two commands must be executed to check BGP neighbor status? (Choose two.)

sa-nsxedge-01(tier0_sr)> get bgp neighbor

sa-nsxedge-01(tier0_dr)> get bgp neighbor

sa-nsxedge-01(tier1_sr)> get bgp neighbor

sa-nsxedge-01(tier0_sr)> get bgp neighbor

Which two of the following will be used for ingress traffic on the Edge node supporting a Single Tier topology? (Choose two.)

Downlink Interface for the Tier-0 DR

Downlink Interface for the Tier-1 DR

Inter-Tier interface on the Tier-0 gateway

Which two tools are used for centralized logging in VMware NSX? (Choose two.)

VMware Aria Operations for Logs

VMware Aria Operations for Networks

Where can an administrator see a visual overview of network connections between different VMs and different networks, within the NSX domain?

VMware Aria Operations for Networks

Which CLI command does an NSX administrator run on the NSX Manager to generate support bundle logs if the NSX UI is inaccessible?

get support-bundle file vcpnv.tgz

esxcli system syslog config logger set --id=nsxmanager

get support-bundle file vcpnv.tgz

set support-bundle file vcpnv.tgz

Which NSX CLI command is used to change the authentication policy for local users?

get auth-policy minimum-password-length

When configuring OSPF on Tier-0 Gateway, which three of the following must match in order to establish a neighbor relationship with an upstream router? (Choose three.)

MTU of the Uplink C Naming convention

Which command is used to set the NSX Manager's logging-level to debug mode for troubleshooting?

sec service nsx-manager log-level debug

set service manager log-level debug

sec service nsx-manager logging-level debug

sec service nsx-manager log-level debug

sec service manager logging-level debug

Which CLI command would an administrator use to allow syslog on an ESXi transport node when using the esxcli utility?

esxcli network firewall ruleset set -r syslog -e true

esxcli network firewall ruleset set -a -e false

esxcli network firewall ruleset set -r syslog -e false

esxcli network firewall ruleset -e syslog

esxcli network firewall ruleset set -r syslog -e true

Which troubleshooting step will resolve an error with code 1001 during the configuration of a time-based firewall rule?

Restarting the NTPservice on the ESXi host.

Reconfiguring the ESXi host with a local NTP server.

Re-installing the NSX VIBs on the ESXi host.

Changing the time zone on the ESXi host.

Which statement is true about an alarm in a Suppressed state?

An alarm can be suppressed for a specific duration in hours.

An alarm can be suppressed for a specific duration in seconds.

An alarm can be suppressed for a specific duration in days.

An alarm can be suppressed for a specific duration in minutes

Which of the following settings must be configured in an NSX environment before enabling stateful active-active SNAT?

A Punting Traffic Group for the NSX Edge uplinks

Tier-1 gateway in active-standby mode

A Punting Traffic Group for the NSX Edge uplinks

An Interface Group for the NSX Edge uplinks

Tier-1 gateway in distributed only mode

VMware 2V0-41.24 Practice Test 2 - Free Online Exam Prep & Questions

What can the administrator use to identify overlay segments in an NSX environment if troubleshooting is required?

Become a Premium Member for full access

Unlock Premium Member

VMware 2V0-41.24 Practice Test 2

Question

VMware 2V0-41.24 Practice Tests

Practice Tests