An engineer is configuring multicast for wireless for an all-company video meeting on a network using EIGRP and BGP within a single domain from a single source. Which type of multicast routing should be implemented?

Protocol Independent Multicast Sparse Mode

Protocol Independent Multicast Dense Mode

Multicast Source Discovery Protocol

Protocol Independent Multicast Sparse Mode

Which statement about the VideoStream/Multicast Direct feature is true?

Each VideoStream client acknowledges receiving a video IP multicast stream.

IP multicast traffic is reliable over WLAN by default as defined by the IEEE 802.11 wireless multicast delivery mechanism.

Each VideoStream client acknowledges receiving a video IP multicast stream.

It converts the unicast frame to a multicast frame over the air.

It makes the delivery of the IP multicast stream less reliable over the air, but reliable over Ethernet.

Which configuration is applied to prevent the network from a Layer 2 flooding of multicast frames with a seamless transfer of multicast data to the client when roaming from one controller to another?

Enable IGMP snooping on the WLC.

Enable IGMPv3 on the central Layer 3 switch.

Enable IGMP snooping on the WLC.

Enable multicast mode on the WLC.

Create multicast groups on the central Layer 3 switch.

An engineer is configuring multicast for two WLCs. The controllers are in different physical locations and each handles around 500 wireless clients. How should the CAPWAP multicast group address be assigned during configuration?

Each WLC must be assigned a unique multicast group address.

Each WLC management address must be in the same multicast group.

Both WLCs must be assigned the same multicast group address.

Each WLC management address must be in a different multicast group.

A wireless network has been implemented to enable multicast video to be streamed reliably over the wireless link to the wireless users. After a client reports that the video is unable to stream, the administrator determines that the client is connecting at a data rate of 12 Mbps and is trying to stream to a valid multicast address on the network. Which two actions must be applied? (Choose two.)

Implement video-stream for the multicast video on the controller.

Allow multicast-direct to work correctly and multicast-direct to be enabled globally.

Turn off IGMP snooping for all the configured WLANs on the controller.

Implement video-stream for the multicast video on the controller.

Allow multicast-direct to work correctly and multicast-direct to be enabled globally.

Change the WLAN QoS value to Bronze for the WLAN that multicast will be enabled.

Allow RTSP to stream the video due to wireless multicast not using acknowledgements.

Which two restrictions are in place with regards to configuring mDNS? (Choose two.)

mDNS is not supported on FlexConnect APs with a locally switched WLAN.

Controller software must be newer than 7.0.6+.

mDNS uses only UDP port 5436 as a destination port.

mDNS cannot use UDP port 5353 as the destination port.

mDNS is not supported on FlexConnect APs with a locally switched WLAN.

Controller software must be newer than 7.0.6+.

mDNS is not supported over IPv6.

A shopping center uses AireOS controllers with Cisco Wave 2 APs. A separate WLAN named Guest- 012345678-WLAN is used for guest wireless clients. Management needs location analytics to determine popular areas. CMX must track only associated clients. What must be selected on the CMX server settings?

Enable Locally Administered MAC Filtering

Which two steps are needed to complete integration of the MSE to Cisco Prime Infrastructure to track the location of clients/rogues on maps? (Choose two.)

Apply a valid license for Wireless Intrusion Prevention System.

Apply a valid license for location tracking.

Synchronize access points with the MSE.

Add the MSE to Cisco Prime Infrastructure using the CLI credentials.

Add the MSE to Cisco Prime Infrastructure using the Cisco Prime Infrastructure communication credentials.

Apply a valid license for Wireless Intrusion Prevention System.

Apply a valid license for location tracking.

An IT department receives a report of a stolen laptop and has information on the MAC address of the laptop. Which two settings must be set on the wireless infrastructure to determine its location?(Choose two.)

Location History for Clients must be enabled on the MSE.

Tracking optimization must be enabled on the WLC.

Location History for Clients must be enabled on the MSE.

Client location tracking must be enabled on the MSE.

Location History for Visitors must be enabled on the MSE.

Location History for Rogue APs & Rogue Clients must be enabled on the MSE.

Tracking optimization must be enabled on the WLC.

Refer to the exhibit. An engineer needs to manage non-802.11 interference. What is observed in the output on PI?

The three individual clusters shown indicate poor AP placement.

At least one strong interferer is impacting connectivity at this site.

Several light interferers are collectively impacting connectivity at this site.

The three individual clusters shown indicate poor AP placement.

RF at this site is unable to provide adequate wireless performance.

After looking in the logs, an engineer notices that RRM keeps changing the channels for non-IEEE 802.11 interferers. After surveying the area, it has been decided that RRM should not change the channel. Which feature must be enabled to ignore non-802.11 interference?

Avoid Persistent Non-WiFi Interference

A network engineer has been hired to perform a new MSE implementation on an existing network.The MSE must be installed in a different network than the Cisco WLC. Which configuration allows the devices to communicate over NMSP?

Allow TCP/16113 port on the firewall.

Allow UDP/16113 port on the central switch.

Allow TCP/16113 port on the firewall.

Allow UDP/16666 port on the VPN router.

Allow TCP/16666 port on the router.

An engineer is managing a wireless network for a shopping center. The network includes a Cisco WLC, a Cisco MSE, and a Cisco Prime Infrastructure. What is required to use Cisco CMX Location Analytics?

Enable Context Aware and CMX Browser Engage.

Enable tracking parameters in Cisco MSE.

Enable Context Aware and CMX Browser Engage.

Install Cisco Prime Infrastructure with floor maps.

Set history parameters in Cisco MSE.

Which two statements about the requirements for a Cisco Hyperlocation deployment are true?(Choose two.)

After enabling Cisco Hyperlocation on Cisco CMX, the APs and the wireless LAN controller must be restarted.

The Cisco Hyperlocation feature must be enabled on the wireless LAN controller and Cisco CMX.

After enabling Cisco Hyperlocation on Cisco CMX, the APs and the wireless LAN controller must be restarted.

NTP can be configured, but that is not recommended.

The Cisco Hyperlocation feature must be enabled on the wireless LAN controller and Cisco CMX.

The Cisco Hyperlocation feature must be enabled only on the wireless LAN controller.

If the Cisco CMX server is a VM, a high-end VM is needed for Cisco Hyperlocation deployments.

The Cisco Hyperlocation detection threshold is currently set to -50 dBm. After reviewing the wireless user location, discrepancies have been noticed. To improve the Cisco Hyperlocation accuracy, an engineer attempts to change the detection threshold to -100 dBm. However, the Cisco Catalyst 9800 Series Wireless Controller does not allow this change to be applied. What actions should be taken to resolve this issue?

Disable Cisco Hyperlocation, change the Cisco Hyperlocation detection threshold, and then enable it.

Create a new profile on Cisco CMX with the new Cisco Hyperlocation detection range, and apply it on the WLAN.

Place the APs to monitor mode, shutdown the radios, and then change the Cisco Hyperlocation detection threshold.

Shutdown all radios on the controller, change the Cisco Hyperlocation detection range, and enable the radios again.

An engineer has successfully implemented 10 active RFID tags in an office environment. The tags are not visible when the location accuracy is tested on the Cisco CMX Detect and Locate window. Which setting on Cisco CMX allows the engineer to view the tags?

Enable RFID tags in tracking options.

Enable probing clients for active tags.

Define an RFID group globally and add the tags.

Enable hyperlocation services for RFID.

An engineer completed the basic installation for two Cisco CMX servers and is in the process of configuring high availability, but it fails. Which two statements about the root of the issue are true?(Choose two.)

The types of the primary and secondary Cisco CMX installations differ.

The sizes of the primary and secondary Cisco CMX installations differ.

The Cisco CMX instances are installed in the same subnet.

The types of the primary and secondary Cisco CMX installations differ.

The delay between the primary and secondary instance is 200 ms.

The sizes of the primary and secondary Cisco CMX installations differ.

Both Cisco CMX installations are virtual.

Refer to the exhibit. The image shows a packet capture that was taken at the CLI of the Cisco CMX server. It shows UDP traffic from the WLC coming into the server. What does the capture prove?

The Cisco CMX server receives Angle-of-Arrival data from the WLC.

The Cisco CMX server receives NetFlow data from the WLC.

The Cisco CMX server receives NMSP traffic from the WLC.

The Cisco CMX server receives SNMP traffic from the WLC.

The Cisco CMX server receives Angle-of-Arrival data from the WLC.

A Cisco CMX 3375 appliance on the 10.6.1 version code counts duplicate client entries, which creates wrong location analytics. The issue is primarily from iOS clients with the private MAC address feature enabled. Enabling this feature requires an upgrade of the Cisco CMX 3375 appliance in a high availability pair to version 10.6.3. SCP transfers the Cisco CMX image, but the upgrade script run fails.Which configuration change resolves this issue?

Break the high availability using the cmxha config disable command and upgrade the primary and secondary individuality.

Upgrade the high availability pair to version 10.6.2 image first and then upgrade to version 10.6.3.

Save configuration and use the upgrade script to upgrade the high availability pair without breaking the high availability.

Break the high availability using the cmxha config disable command and upgrade the primary and secondary individuality.

Run root patch to first upgrade to version 10.6.2 and then migrate to version 10.6.3.

What are two considerations when deploying a Cisco Hyperlocation? (Choose two.)

After enabling Cisco Hyperlocation on Cisco CMX, the APs and the wireless LAN controller must be restarted.

The Cisco Hyperlocation feature must be enabled on the wireless LAN controller and Cisco CMX.

NTP configuration is available, but not recommended.

The Cisco Hyperlocation feature must be enabled only on the wireless LAN controller.

After enabling Cisco Hyperlocation on Cisco CMX, the APs and the wireless LAN controller must be restarted.

The Cisco Hyperlocation feature must be enabled on the wireless LAN controller and Cisco CMX.

If the Cisco CMX server is a VM, a high-end VM is needed for Cisco Hyperlocation deployments.

After installing and configuring Cisco CMX, an administrator must change the NTP server on the Cisco CMX server. Which action accomplishes this task?

Manually edit /etc/ntp.conf as the admin user before restarting ntpd by using service ntpd restart.

Manually edit /etc/ntp.conf using an XML editor before restarting the server by using service restart all services.

Log in to the Cisco CMX CLI and issue set ntp server NTP_IP where NTP_IP is the IP of the NTP server.

Manually edit /etc/ntp.conf as the admin user before restarting ntpd by using service ntpd restart.

Log in to the Cisco CMX GUI as the administrator and type the IP address of the NTP server in System tab > Settings> TimeZone/NTP.

A company has a single WLAN configured for 802.1x authentication with the QoS set to Silver. This WLAN supports all corporate and BYOD access. A decision has been made to allow users to install Cisco Jabber on their personal mobile devices. Users report poor voice quality when using Jabber.QoS is being applied only as best effort. What must be configured to ensure that the WLAN remains on the Silver class and to ensure Platinum class for Jabber?

Configure an AVC profile for the Jabber traffic and apply it to the WLAN.

Configure QoS on the mobile devices that have Jabber installed.

Enable Cisco Centralized Key Management on the WLAN so that the Jabber-enabled devices will connect.

Configure the WLAN to broadcast on 5 GHz radios only and allow Jabber users to connect.

Configure an AVC profile for the Jabber traffic and apply it to the WLAN.

Cisco 300-430 Practice Test 2 - Free Online Exam Prep & Questions

Question 1 / 40

An engineer has been hired to implement a way for users to stream video content without having issues on the wireless network. To accomplish this goal, the engineer must set up a reliable way for a Media Stream to work between Cisco FlexConnect APs. Which feature must be enabled to guarantee delivery?

Unicast Direct

IGMP Direct

Multicast Direct

Multicast-to-Unicast Direct

Comment (0)

Cisco 300-430 Practice Test 2

Question

Cisco 300-430 Practice Tests

Practice Tests