Which configuration must an administrator perform to display Translation Pattern operations in Cisco Unified Communications Manager SDL traces?

By default, the Translation Patterns operations are printed in SDL traces, so no additional configuration is necessary.

Enable the Detailed Call Analysis option under Enterprise Parameters for Unified CM.

Set up the Digit Analysis Complexity in Service Parameters for Cisco Unified CM to TranslationAndAlternatePatternAnalysis.

Check the Translation Patterns Analysis check box in Micro Traces on the Cisco Unified CM Serviceability page.

By default, the Translation Patterns operations are printed in SDL traces, so no additional configuration is necessary.

Refer to the exhibit. Users report that when they dial the emergency number 9911 from any internal phone, it takes a long time to connect with the emergency operator. Which action resolves this issue?

Check the Urgent Priority check box under 9.911 pattern.

Adjust the service parameter T302 timet to the desired value.

Adjust the service parameter T204 timer to the desired value.

Check the Urgent Priority check box under 9.911 pattern.

Point the emergency pattern directly to the PSTN gateway.

Refer to the exhibit. An administrator is troubleshooting a situation where a call placed from a phone registered to Cisco Unified Communications Manager does not complete. The administrator wants to use the Dialed Number Analyzer on Cisco Unified CM to check which translation pattern the call is matching. However, when logging in to Cisco Unified Serviceability there is no option for Dialed Number Analyzer under the tool menu. Which two steps must be performed to resolve this issue? (Choose two.)

Activate the Cisco Dialed Number Analyzer service.

Activate the Cisco Dialed Number Analyzer Server service.

Activate the Cisco Extended Functions service.

Activate the Cisco CallManager service.

Activate the Cisco Dialed Number Analyzer service.

Activate the Cisco Dialed Number Analyzer Server service.

Refer to the exhibit. Within the North American Numbering Plan, gateways located in Ottawa, Canada and marked as ''YOW'' are assigned to the Calling Party Transformation CSS NANP_CgPTP, which contains partition NANP_calling_xforms. What is the calling-party number and the numbering type if the calling user +1613-555-1234 dials the number?

calling number 613-555-1234 and numbering type ''national''

calling number 613-555-1234 and numbering type ''subscriber''

calling number 011-1-613-555-1234 and numbering type ''subscriber''

calling number 011613-555-1234 and numbering type ''international''

calling number 613-555-1234 and numbering type ''national''

Where on Cisco Unified Communications Manager do you configure the standard local route group for a group of devices?

Call Routing > Route/Hunt > Local Route Group Names

Call Routing > Emergency Location > Emergency Location (ELIN) Groups

How does an engineer globalize routing for ingress calls coming from the PSTN to internal DNs?

At Cisco Unified Communications Manager, put the calling number in E.164 format and the called number in E.164 format.

At the PSTN gateway, put the calling number in PSTN format and the called number in DN format.

At Cisco Unified CM, put the calling number in E.164 format and the called number in PSTN format.

At the PSTN gateway, put the calling number in E.164 format and the called number in localized (DN) format.

At Cisco Unified Communications Manager, put the calling number in E.164 format and the called number in E.164 format.

An engineer is configuring a call park feature in Cisco Unified Communications Manager Express. Which command does the engineer use to ensure that the call is reverted to the user after 60 seconds?

R2(config-ephone-dn)#park-slot timeout 30 limit 2 recall alternate 3002

R2(config-ephone-dn)#park reservation-group 60

R2(config-ephone-dn)#park-slot timeout 60 limit 2 recall alternate 3002

R2(config-ephone-dn)#park reservation-group 1

R2(config-ephone-dn)#park-slot timeout 30 limit 2 recall alternate 3002

When locations-based Call Admission Control denies the call, which two masks can AAR apply when routing the call through the PSTN? (Choose two.)

enterrise alternate number mask

Which two configuration parameters are prerequisites to set Native Call Queuing on Cisco Unified Communications Manager? (Choose two.)

Cisco IP Voice Media Streaming Service must be activated on at least one node in the cluster.

Cisco RIS data collector service must be running on the same server as the Cisco CallManager service.

Cisco IP Voice Media Streaming Service must be activated on at least one node in the cluster.

A unicast music on hold audio source must be configured.

Cisco RIS data collector service must be running on the same server as the Cisco CallManager service.

The maximum number of callers allowed in queue must be 10.

The phone button template must have the Queue Status Softkey configured.

What is the relationship between partition, time schedule, and time period in Time-of-Day routing in Cisco Unified Communications Manager?

A partition can have multiple time schedules assigned. A time schedule contains one or more time periods.

A partition can have one time schedule assigned. A time schedule contains one or more time periods.

A partition can have multiple time schedules assigned. A time schedule contains only one time period.

A partition can have one time schedule assigned. A time schedule contains only one time period.

Configure Call Queuing in Cisco Unified Communications Manager. Where do you set the maximum number of callers in the queue?

in the telephony service configuration

in Cisco Unified CM Enterprise Parameters

in Cisco Unified CM Service Parameters

A user reports that when they attempt to log out from the Cisco Extension Mobility service by pressing the Services button, they cannot log out. What is the most likely cause of this issue?

The user device profile is not subscribed to the Cisco Extension Mobility service.

The Cisco Extension Mobility service has not been configured on the phone.

There might be a significant delay between the button being pressed and the Cisco Extension Mobility service recognizing it. It would be best to check network latency.

The user device profile has not been assigned to the user.

The user device profile is not subscribed to the Cisco Extension Mobility service.

When the services key is pressed Cisco Extension Mobility does not show up. What is the cause of the issue?

The phone is not subscribed to Cisco Extension Mobility Service.

The URL configured for Cisco Extension Mobility is not correct.

Cisco Extension Mobility Service is not running.

The phone is not subscribed to Cisco Extension Mobility Service.

Cisco Extension Mobility is not enabled in the Phone Configuration Window (Device > Phone)

A user reports when they press the services key they do not receive a user ID and password prompt to assign the phone extension. Which action resolves the issue?

Subscribe the phone to the Cisco Extension Mobility service.

Create the default device profiles for all phone models that are used.

Subscribe the phone to the Cisco Extension Mobility service.

Create the end user and associate it to the device profile.

Assign the extension as a mobile extension.

What are the elements for Device Mobility configuration?

physical location, device pool, and Device Mobility group

device pool, Device Mobility group, and region

physical location. Device Mobility group, and region

device pool, Device Mobility group, and Cisco IP phone

An engineer is implementing survivability for a collaboration environment. The environment is utilizing a centralized Cisco UCM at the headquarters and Cisco IOS-XE gateways in the remote branches. Which action must the engineer take to enable both shared lines and B-ACD for SIP branch phones during a WAN outage?

Configure mode esrst under voice register global configuration mode.

Configure mode srst under telephony-service configuration mode.

Configure mode esrst under telephony-service configuration mode.

Configure mode esrst under voice register global configuration mode.

Configure mode esrst under voice service voip configuration mode.

Refer to the exhibit. A user cannot call number 730. which Is an abbreviated number for 45730. The engineer recently configured a translation pattern In Cisco UCM. The newly configured translation pattern of 7XX prefixes the digits 45. The engineer uses DNA to troubleshoot the issue. What is the reason for this problem?

The abbreviated partition is missing from the calling search space.

The translation pattern is blocking the call.

The translation pattern Is misconfigured.

Directory number 45730 is unknown to Cisco UCM.

Refer to the exhibit. A no-way audio situation was experienced after the calling party on an outbound call placed the call on hold and then resumed from hold. Which action will resolve the issue?

Upgrade the Cisco Unified Border Element to 15.2.

Assign an MTP to the SIP trunk.

Restart the SIP trunk on Cisco UCM.

Upgrade the Cisco Unified Border Element to 15.2.

Upgrade the Cisco Unified Border Element device.

Which services are needed to successfully implement Cisco Extension Mobility in a standalone Cisco Unified Communications Manager server?

Cisco CallManager, Cisco TFTP, and Cisco Extension Mobility

Cisco Extended Functions, Cisco Extension Mobility, and Cisco AXL Web Service

Cisco CallManager, Cisco TFTP, and Cisco CallManager SNMP Service

Cisco CallManager, Cisco TFTP, and Cisco Extension Mobility

Cisco TAPS Service, Cisco TFTP, and Cisco Extension Mobility

Due to a shortage of physical interfaces on a device the administrator requires that a loopback for RTP is used. Which command is required when using a loopback interface for RTP?

voice-class sip bind media source-interface Loopback0

voice-class sip resources priority mode passthrough

voice-class sip bind control source-interface Loopback0

voice-class sip early-offer forced.

voice-class sip bind media source-interface Loopback0

Refer to the exhibit. An engineer is troubleshooting an issue where inbound calls to Cisco UCM with early media fail to establish. While investigating the issue, the engineer finds that Cisco UCM is set to require a PRACK. but the Cisco Unified Border Element is not sending it. Which command is causing this issue?

voice-class sip early-media update block

voice-class midcall-signaling block

An engineer must implement call restriction to toll-free numbers using a class of restriction in a branch Cisco UCME. In which two places is the corlist incoming or cor Incoming command configured? (Choose two.)

'voice register pool' configuration mode

'voice register global' configuration mode

'telephony-service' configuration mode

'voice register pool' configuration mode

'dial-peer cor custom' configuration mode

CollabCorp is a global company with two clusters, emea.collab corp and apac.collab.corp. URI dialing is implemented and working in each cluster. The company configured routing between clusters to make inter-cluster calls via URI. but this is not working as expected. Which two configuration elements should be checked to resolve this issue? (Choose two.)

calling search space and partition

An administrator discovers that employees are making unauthorized long-distance and international calls from logged-off Extension Mobility phones when the authorized users are away from their desks Which two configurations should the administrator configure in the Cisco UCM to avoid this issue? (Choose two.)

Remove the long-distance & international pattern's partitions from the calling search space of the physical phone.

Add the long-distance & international pattern's partitions to the calling search space of the device profile

Remove the long-distance & international pattern's partitions from the calling search space of the physical phone.

Add the long-distance & international pattern's partitions to the calling search space of the physical phone's directory number.

Remove the long-distance & international pattern's partitions from the calling search space of the device profile.

Add the long-distance & international pattern's partitions to the calling search space of the physical phone.

Add the long-distance & international pattern's partitions to the calling search space of the device profile

Refer to the exhibit. A user dials 84969010 and observes that the call is not routed immediately. The administrator notices that after matching the fixed-length translation pattern, the call hits the \+! pattern and waits for interdigit timeout What should be configured to ensure that the call routes out immediately?

Do Not Wait For Interdigit Timeout On Subsequent Hops on the translation pattern

Allow Device Override on the route pattern

Route Next Hop By Calling Party Number on the translation pattern

Do Not Wait For Interdigit Timeout On Subsequent Hops on the translation pattern

Do Not Wait For Interdigit Timeout On Subsequent Hops on the route pattern

An engineer is troubleshooting Cisco Device Mobility and find that the phone has roamed to a building that is assigned to a different device pool but has not changed its device pool accordingly What action resolves the issue?

Set the correct subnet under Device Mobility Info.

Set correct Location under Current Device Mobility Settings

Enable SRST under Current Device Mobility Settings

Set the correct subnet under Device Mobility Info.

Set Device CSS under Current Device Mobility Settings.

A customer is using a SIP trunk to route calls to ITSP to decrease the possibility of downtime, the customer invested in a failover device How does the customer ensure reachability to ITSP, so that if one device on ITSP fails, the calls will be routed to another device?

Enable SIP Option Ping on the SIP profile.

Enable transmit security status on the SIP security profile

Enable ANAT on the SIP profile.

Monitor the link using network management toots, and if it fails, manually change the routing to another working device.

Enable SIP Option Ping on the SIP profile.

Calls to a particular extension are not routing to voicemail. The user reaches the voicemail system from the handset by pressing the Messages button Which configuration parameter causes this problem?

The voicemail pilot number for call forwarding is missing from the ephone-dn

The voicemail pilot number is missing from the call handling on Cisco Unity Express

The voicemail pilot number is missing from the telephony service configuration on Cisco UCME

The voicemail pilot number for call forwarding is missing from the ephone

Cisco 300-815 Practice Test 2 - Free Online Exam Questions 41-80

In Cisco Unified Communications Manager, which tool do you use to check SIP traces?

MTP

CCSIP

RTMT

OS Administration Page

Comment (0)

Cisco 300-815 Practice Test 2

Question

Cisco 300-815 Practice Tests

Practice Tests