FRF.5 is a standard that describes which of the following requirements?

Frame Relay tunneling over an ATM core network.

ATM to Frame Relay translation.

Frame Relay to Ethernet translation.

ATM tunneling over a Frame Relay core network.

Frame Relay tunneling over an ATM core network.

Frame Relay tunneling over an MPLS/IP core network

Which of the following statements are TRUE regarding a fully meshed VPLS service with a default setting? (Choose 3)

The vc-id on the mesh-sdp must be explicitly configured.

The VPLS service id, on all PE routers, must match.

The signaling on all PE routers will default to TLDP in the configuration of the SDPs; therefore, no configuration change is required for dynamic signaling.

The vc-id on the mesh-sdp must be explicitly configured.

The vc-id on the mesh-sdp is automatically assigned by a PE using the service id.

The VPLS service id, on all PE routers, does not have to match.

The VPLS service id, on all PE routers, must match.

If dynamic signaling is required, the signaling on all PE routers must be set to TLDP in the configuration of the SDPs.

The signaling on all PE routers will default to TLDP in the configuration of the SDPs; therefore, no configuration change is required for dynamic signaling.

Which of the following statements are TRUE about configuring a SDP between an IES and a VPLS? (Choose 2)

The Layer 2 MTUs must match between the IES and the VPLS

Once the SDP is configured on both PE routers, both the services will be operationally up without further configuration changes.

The Layer 2 MTUs must match between the IES and the VPLS

The Layer 2 MTU must be 14 bytes smaller on the VPLS than it is on the IES.

Port 1/1/1 has been configured as an access port with encapsulation dot1q on an Nokia 7750 SR. Which of the following statements are TRUE? (Choose 2)

TheSAP1/1/1:400 will forward customer traffic tagged with VLAN 400

The SAP 1/1/1:0 will forward untagged traffic and traffic tagged with VLAN 0

The SAP 1/1/1 will forward all traffic transparently.

The SAP 1/1/1:0.* will forward all untagged traffic and traffic tagged with VLAN 0.

The SAP 1/1/1:* will forward untagged traffic but not tagged traffic.

TheSAP1/1/1:400 will forward customer traffic tagged with VLAN 400

The SAP 1/1/1:0 will forward untagged traffic and traffic tagged with VLAN 0

Which of the following most accurately describes the default behavior of a VPLS regarding the handling of a tagged frame at the ingress of SAP 1/1/1:100?

The FCS is verified and removed from the frame. The VLAN tag is removed for transport over the network.

The FCS is verified and the customer frame is transported intact over the service provider network.

The FCS is verified and kept in the customer frame. The VLAN tag is removed for transport over the network.

The FCS is verified and removed from the frame. The VLAN tag is kept for transport over the network.

The FCS is verified and removed from the frame. The VLAN tag is removed for transport over the network.

What happens when a packet without a VLAN tag is received on a SAP provisioned with null encapsulation while an SDP vc-type is provisioned as vlan?

A VLAN tag of 0 is added as the provider VLAN tag

The service ID is added as the VLAN tag.

A VLAN tag of 0 is added as the provider VLAN tag

The frame is forwarded with no VLAN tag

What distinguishes a VPLS service from a VPWS service?

VPLS supports multipoint-to-multipoint connections

VPLS supports point-to-point connections.

VPLS supports multipoint-to-multipoint connections

VPLS supports a distributed service

VPLS supports a local service on a single node.

Which of the following statements best describes the flooding of traffic on a PE when traffic is received on a SAP?

Traffic is flooded to all SAPs, spoke SDPs, and mesh SDPs in the service.

Traffic is flooded to all SAPs in the service.

Traffic is flooded to all SAPs and spoke SDPs in the service.

Traffic is flooded to all SAPs and mesh SDPs in the service.

Traffic is flooded to all SAPs, spoke SDPs, and mesh SDPs in the service.

How many SAPs can be configured on a port configured with NULL encapsulation?

None. This encapsulation is not supported.

The number is limited only by the capacity of the router

Customer 'A' has sites on 3 different Nokia PE routers. The routers are connected to each other through an IP/MPLS network in a full mesh fashion. Customer 'A' requires a VPLS service. Which of the following statements are TRUE? (Choose2)

Each router requires 1 VPLS service.

Each router requires 2 VPLS services.

Each router requires 1 SDP with 2 LSPs, one to each of the other 2 routers.

Which of the following statements best describes the flooding of traffic on a PE when traffic is received on a spoke SDP?

Traffic is flooded to all SAPs, spoke SDPs, and mesh SDPs in the service

Traffic is flooded to all SAPs in the service.

Traffic is flooded to all SAPs and spoke SDPs in the service.

Traffic is flooded to all SAPs and mesh SDPs in the service.

Traffic is flooded to all SAPs, spoke SDPs, and mesh SDPs in the service

What does a PE do when a frame is received in a VPLS service with an unknown destination address by default?

Flood the frame to all PEs participating in the service.

Send a destination unreachable message back to the originating host.

Store the frame until the destination is known

Which of the following statements is TRUE?

An OSPF adjacency can be established on an IES interface.

IES allows provider MP-BGP sessions to be extended to customers.

An IES service must use static routes in order to communicate with customer networks.

An IES interface supports OSPF and IS-IS in passive mode only.

What are the two major differences between configuring an IES service and configuring VPWS or VPLS services? (Choose 2)

An IES interface has an IP address assigned to it.

A virtual route table must be configured for an IES service.

An IES interface has an IP address assigned to it.

What can the sdp-ping command be used for? (Choose 2)

To test the ability of reaching the far-end IP address of an SDP within the SDP encapsulation

To determine the path MTU to the far-end IP address over an SDP.

To test the ability of reaching the far-end IP address of an SDP within the SDP encapsulation

To determine the path MTU to the far-end IP address over an SDP.

To determine the service MTU of the service using an SDP.

To determine the presence of hosts using the service

Which of the following statements are TRUE regarding sdp-ping? (Choose 3)

Provides in-band uni-directional connectivity tests.

Provides in-band round-trip connectivity tests.

Tests ability of reaching the far-end IP address of an SDP ID within the SDP encapsulation.

Provides a mechanism to determine the hops an SDP traverses.

Provides in-band uni-directional connectivity tests.

Provides in-band round-trip connectivity tests.

Tests ability of reaching the far-end IP address of an SDP ID within the SDP encapsulation.

Provides information regarding the exact MTU supported between service ingress and service termination.

Which of the following items can NOT be used as a mirror source?

All of the above can be used as a mirror source.

Ingress MPLS frames with a specific label.

Entries that match an IP filter.

Entries that match a MAC filter.

All of the above can be used as a mirror source.

A technician sitting in a Network Operations Center would like to set up a remote mirror on an Nokia 7750 Service Router to examine some data traffic ingressing a port at a remote site. Which of the following are required? (Choose 2)

A mirror destination on the local and remote Nokia Service Router,

An SDP between the local and remote Nokia Service Routers.

A mirror destination on the local and remote Nokia Service Router,

A mirror source on the local and remote Nokia Service Router.

A mirror source with the remote source specified on the remote Nokia Service Router.

A mirror source with the remote source specified on the local Nokia Service Router.

An SDP between the local and remote Nokia Service Routers.

Click on the exhibit button below. Assuming the customer only needs to monitor traffic from PE3 to the customer site, what three items are missing from PE3's configuration? (Assume that the IP/MPLS network structure between the local and remote PEsis in place.)

The mirror destination configuration on PE5 is missing the 'remote-source' command,

The mirror service IDs on the local and remote destinations must match.

The mirror source command on the remote PE3 needs a command that tells it to monitor port 1/1/2.

The mirror destination configuration on PE5 is missing the 'remote-source' command,

The mirror destination on PE3 needs a 'remote-source' command.

The mirror service IDs on the local and remote destinations must match.

The mirror source on PE3 needs a 'remote-source' command.

The mirror source command on the remote PE3 needs a command that tells it to monitor port 1/1/2.

Which of the following commands is used to configure a new MPLS SDP?

configure service sdp sdp-id mpls create

configure service sdp sdp-id create

configure service mpls sdp sdp-id create

configure service gre sdp sdp-id create

configure service sdp sdp-id mpls create

Which of the following commands is used to create a new Epipe service?

configure service epipe service-id customer customer-id create

configure epipe service-id customer customer-id create

configure service epipe service-id customer customer-id create

configure epipe service-id create

configure epipe service-id customer customer-id create

configure epipe service service-id customer customer-id create

When configuring RSVP-TE for transport tunnels, which command enables RSVP by default?

configure router transport-tunnel

Which of the following conditions are necessary in order for service labels to be signaled between two PE routers? (Choose 3)

LDP must be enabled on both PE routers.

The VC-ID must match between the two PE routers in both directions.

The transport tunnel must be operationally up between the two PE routers in both directions.

LDP must be enabled on both PE routers.

RSVP must be enabled on both PE routers.

Traffic engineering must be enabled in the IGP.

The VC-ID must match between the two PE routers in both directions.

The transport tunnel must be operationally up between the two PE routers in both directions.

The SDP ID must match between the two PE routers in both directions.

Which of the following statements are TRUE about configuring a distributed Epipe service? (Choose 2)

The vc-id on the spoke-sdp must be explicitly configured.

The vc-id on the spoke-sdp can be configured to match the service id.

The vc-id on the spoke-sdp must be explicitly configured.

The vc-id on the mesh-sdp must be explicitly configured.

The vc-id on the spoke-sdp can be configured to match the service id.

The vc-id on the mesh-sdp can be configured to match the service id.

The vc-id on the spoke-sdp does not have to be explicitly configured and will use the service id.

The vc-id on the mesh-sdp does not have to be explicitly configured and will use the service id.

Nokia 4A0-104 Practice Test 2 - Free Online Exam Questions 41-80

Spam

Selling illegal goods, money scams etc.

Hate Speech

Serious attack on a group.

Harassment and bullying

Harassing an individual (including doxing)

Harmful activities

Threatening or glorifying violence or serious harm, including self-harm

Adult content (Consensual)

Nudity/Sexual content

Sexual exploitation and abuse (child safety)

Sexually explicit or suggestive imagery or writing involving minors

Sexual exploitation and abuse (adults and animals)

Sexually explicit or suggestive imagery or writing involving non-consenting adults or non-humans

Plagiarism

Reusing content without attribution (link and blockquotes)

Poorly written

Not in English or has very bad formatting, grammar, and spelling

Inappropriate credential

Author's credential is offensive, spam, or impersonation

Other

Ex. Illegal content, incomplete question...

Nokia 4A0-104 Practice Test 2

Question

Drag and Drop

Hot Area

Nokia 4A0-104 Practice Tests

Practice Tests