Which order is accurate for a firmware upgrade on MX appliances in a high-availability configuration?

starts on the primary MX appliance and then occurs on the secondary MX appliance

starts on the secondary MX appliance and then occurs on the primary MX appliance

starts on both MX appliances at the same time and then reboots both appliances after traffic on the primary MX appliance ceases

starts on both MX appliances at the same time and then immediately reboots both appliances

starts on the primary MX appliance and then occurs on the secondary MX appliance

How is high-availability supported for Cisco Meraki devices?

The MX Security Appliances and MS Series Switches that use VRRP support an active/passive high- availability pair.

Only the MX Security Appliances that use VRRP support high availability.

An active/active high-availability pair is recommended for MX Security Appliances.

The MX Security Appliances and MS Series Switches that use VRRP support an active/passive high- availability pair.

The MX Security Appliances and MS Series Switches that use HSRP support an active/passive high- availability pair.

Refer to the exhibit. What is an advantage of implementing inter-VLAN routing on an MX Security Appliance rather than performing inter-VLAN routing on an MS Series Switch?

The MX appliance performs data encryption for inter-VLAN traffic.

The MX appliance performs IDS/IPS for inter-VLAN traffic.

The MX appliance performs AMP for inter-VLAN traffic.

The MX appliance performs data encryption for inter-VLAN traffic.

The MX appliance performs content filtering for inter-VLAN traffic.

Which API endpoint clones a new Organization?

POST /organizations/{organizationId}/clone

POST /organizations/clone/{organizationId}

PUT /organizations/{organizationId}/clone

POST /organizations/{organizationId}/new

POST /organizations/{organizationId}/clone

Refer to the exhibit. During a Meraki AP deployment, the default SSID that the exhibit shows is broadcast. What causes this behavior?

An AP has never connected to the Meraki Cloud Controller.

An AP does not have a wired connection to the network.

An AP cannot connect to the default gateway.

An AP has never connected to the Meraki Cloud Controller.

An AP has Site Survey mode enabled.

Refer to the exhibit. Refer to the exhibit. What Is the ratio of internet-bound flows that route via WAN 1 compared with WAN 2?

All flows agrees via WAN 1:1 ratio.

All flows alternate in a 5:1 ratio.

All flows alternate in a 2:1 ratio.

All flows agrees via WAN 1:1 ratio.

Refer to the exhibit. Which condition or conditions will cause the 'All Databases & cloud services' SD-WAN traffic to be routed via a VPN2 tunnel on WAN2?

WAN1 tunnel latency is 20 ms or more, and WAN2 tunnel meets the configured performance criteria.

WAN1 tunnel latency is 20 ms or less, irrespective of WAN2 tunnel performance.

WAN1 tunnel latency is 20 ms or more, and WAN2 tunnel meets the configured performance criteria.

WAN1 tunnel latency is 20 ms or less, and WAN2 tunnel meets the configured performance criteria.

WAN1 tunnel latency is 20 ms or more, irrespective of WAN2 tunnel performance.

Refer to the exhibit. Which two configurations are needed to successfully monitor custom applications that a user is accessing using Cisco Meraki Insight? (Choose two)

The custom application uses HTTP on port 8080.

The custom application uses HTTPS on TCP 443.

The custom application uses TLS on any ports.

The custom application uses HTTP on port 8080.

The custom application uses HTTPS on TCP 443.

The custom application uses SMB/CIFS.

The custom application uses HTTPS on port 8080.

What are two methods of targeting and applying management profiles to System Manager clients? (Choose two.)

by defining a range of serial numbers

Which enrollment method must be used when containerization is required on BYOD Android devices managed by Systems Manager?

Android Enterprise utilizing a Work Profile

Android Business utilizing a BYOD Profile

Refer to the exhibit. Why does the end user complain of poor wireless performance?

Channel 48 utilization is at 84 percent.

Non-802.11 traffic of 18 percent indicates poor AP placement.

The client is connected to the secondary radio of the AP instead of the primary radio

The client is using a 20 MHz channel width to connect.

A Cisco Meraki MX security appliance is trying to route a packet to the destination IP address of 172.18.24.12. Which routes contained in its routing table does it select?

non-Meraki VPN route 172.18.24.0/24

directly connected 172.18.16.0/20

Which VLAN is used to source pings across the site-to-site VPN when using the MX Live tools?

highest VLAN ID that is configured and set to YES to use VPN

highest VLAN ID that is configured and set to NO to use VPN

lowest VLAN ID that is configured and set to YES to use VPN

highest VLAN ID that is configured and set to YES to use VPN

lowest VLAN ID configured and set to NO to use VPN

A new application needs to be pushed to all iOS devices. Some devices report ''NotNow'' in the event log and do not install the application.What does the ''NotNow'' event indicate?

The device is locked with a passcode.

The application requires the most recent iOS version.

The device is locked with a passcode.

The device cannot connect to Apple servers.

The device cannot connect to Cisco Meraki servers.

Which information is used to calculate whether a WAN link has high usage?

value under Security & SD WAN > SD WAN & Traffic Shaping > Uplink Configuration

data under Security & SD WAN > Appliance Status > Uplink > Live Data

total historical throughput of an uplink

total number of devices that are actively passing traffic

value under Security & SD WAN > SD WAN & Traffic Shaping > Uplink Configuration

Which configuration step is necessary when automatic updating is required of iOS apps provisioned through Systems Manager that are found in the App Store?

No configuration step is necessary; automatic updating is the default behavior.

Configure automatic updating of iOS devices in the Meraki installed profile.

Create a security policy that enables automatic updates.

Create a profile with automatic update enabled and apply it to iOS devices.

Cisco 500-220 Practice Test 2 - Free Online Exam Prep & Questions

Air Marshal has contained a malicious SSID.

What are two effects on connectivity? (Choose two.)

Become a Premium Member for full access

Unlock Premium Member

Cisco 500-220 Practice Test 2

Question

Cisco 500-220 Practice Tests

Practice Tests