What describes Dell EMC PowerStore X front-end cabling?

Management and discovery use the same cables and connections as storage

Uses internal VMware virtual switching and does not require a management network

Management and discovery use the same cables and connections as storage

Storage and management use the same LACP bonded cable connection

Uses VLTi data switch interconnectivity to support vMotion networks

What does the command 'svc_journalctl -f -g 'st_io_monitor''do?

Retrieves log messages from the specified error and watches for re-occurrence

Deletes all logs before the specified error

Rotates the log based on the specified error

Ignores log messages from the specified error and re-occurring errors

Retrieves log messages from the specified error and watches for re-occurrence

While on-site installing a Dell EMC PowerStore T system, the node A embedded module management Ethernet port link LED is off. What does this indicate?

No network connection is established

Network connection is established

No network connection is established

How is a service laptop IP configured to connect to the Service LAN port of a Dell EMC PowerStore node?

Static IP: 128.221.1.249 and netmask: 255.255.255.0

Static IP: 169.254.1.249 and netmask: 255.0.0.0

Leave IP address and netmask unconfigured

Static IP: 128.221.1.249 and netmask: 255.255.255.0

Obtain IP address from DHCP on PowerStore

Which reference source provides service information and FRU procedures for Dell EMC PowerStore?

DELL EMC PowerStore Product Page

A Storage Administrator notices two fans in a Dell EMC PowerStore are faulted. What describes the system behavior in this circumstance?

An increased fan speed signal is sent to the surviving fans and the system continues normal operations

Upon the second fan fault, all host I/O is terminated immediately and the PowerStore goes through the halt and vault process and shuts down

A five-minute timer starts upon the second fan fault and the system shuts down automatically after the timer expires

CPU clock speed is reduced by 50% to lower internal temperatures and the system continues normal operations

What describes Dell EMC PowerStore heat dissipation?

Lower model numbered systems have lower heat dissipation specifications than higher model numbered systems

X systems have higher heat dissipation specifics than T systems

Higher model numbered systems have lower heat dissipation specifications than lower model numbered systems

T systems have higher heat dissipation specifics than X systems

How can the PUHC health check results be viewed?

In Details of Appliances and Nodes

From where can a data collection be initialized within Dell EMC PowerStore Manager?

Appliance, node, and storage resource

Cluster, appliance, and event log

Node, storage resource, and alerts

A Storage Administrator needs root access. What command needs to be run?

svc_inject generate-key -- root

How many nodes are in the base enclosure?

2 nodes configured as Active-Standby

1 node with high availability enabled

2 nodes configured as Active-Active

What does the output of the PSTCLI command 'nas_server show' display from a Dell EMC PowerStore T?

If NAS servers are present and if they are either Started or Degraded

Memory utilization and thread count for NFS NAS servers

SIDs of SMB NAS servers joined to the AD domain

If NAS servers are present and if they are either NFS or Licensed

If NAS servers are present and if they are either Started or Degraded

A Storage Administrator notices a Critical alert present in Dell EMC PowerStore Manager relating to data integrity. What action within the alert details slide-out panel is helpful in troubleshooting the problem?

Select the Gather Support Materials from Service and Support

Examine Notifications to obtain a list of corrective actions

Access the Repair Flow link to schedule a support engagement

Re-engage support through previous listed Related Events

Select the Gather Support Materials from Service and Support

What is the result of setting a VLAN ID of 0 on a network when running ICW for Dell EMC PowerStore?

Network will pass untagged traffic

Network will pass tagged traffic

Network will pass untagged traffic

A Storage Administrator has an existing single appliance Dell EMC PowerStore 3000T cluster. An additional PowerStore 9000T has been purchased to add into the existing cluster.How does the administrator proceed?

Add the new 9000T appliance into the cluster per the procedure; mixed models of the same type are supported

Additional VLT links on the ToR switching must be configured for the 9000T to support the increased inter-switch network load

The new appliance cannot be added to the cluster; appliance model and type must match when clustering appliances together

Remove two of the four NVMe NVRAM drives from the 9000T; the caching configuration of all clustered appliances must match

What describes the SAS cabling when adding an expansion enclosure to a Dell EMC PowerStore, for each node and expansion enclosure side?

SAS cabling goes from existing A ports to new B ports. At the last enclosure, SAS cabling returns from the A ports to the alternate node's B ports.

SAS cabling goes from existing B ports to new A ports. At the last enclosure, SAS cabling returns from the B ports to the alternate node's A ports.

SAS cabling goes from existing A ports to new B ports. At the last enclosure, SAS cabling returns from the A ports to the originating node's B ports.

SAS cabling goes from existing B ports to new A ports. At the last enclosure, SAS cabling returns from the B ports to the originating node's A ports.

SAS cabling goes from existing A ports to new B ports. At the last enclosure, SAS cabling returns from the A ports to the alternate node's B ports.

When a Dell EMC PowerStore node powers up in service mode, what are the commands and sequence used from the appliance SSH client to restore the node back to normal?

svc_rescue_state clear svc_node reboot

svc_node restart svc_rescue_state start

svc_node shutdown svc_rescue_state clear

svc_rescue_state clear svc_node reboot

svc_rescue_state normal svc_node start

DELL D-PST-MN-A-24 Practice Test 1 - Free Online Exam Prep & Questions

Question 1 / 40

Which LED combination shows a connected and working node?

power LED: blinking green fault LED: blue

power LED: blinking green fault LED: off

power LED: steady green fault LED: off

power LED: steady green fault LED: amber

Comment (0)

DELL D-PST-MN-A-24 Practice Test 1

Question

DELL D-PST-MN-A-24 Practice Tests

Practice Tests