[Cisco Equipment and Related Hardware]Which Cisco collaboration component is an enterprise-grade, cloud-based PBX system that enables devices to register to the cloud?

Cisco Hosted Collaboration Solutions

[Wireless Device Support]What is the primary function of a wireless LAN controller in a Cisco Unified Wireless Network solution?

To manage and configure associated access points centrally

To operate at Layer 3 of the OSI model

To translate data into a frame format for transmission

To provide wireless connectivity to LAN devices

[Cisco Equipment and Related Hardware]What are two indicators that a network interface card must be replaced? (Choose two.)

Inability to save configurations

[Maintenance and RMA Procedures]Which step must be performed immediately after disconnecting the network cable when replacing an SFP transceiver module?

Reinstall dust plugs in the optical bores.

Install the replacement SFP module.

[Cisco Equipment and Related Hardware]How must the power to a system with dual power supplies on a Cisco Nexus switch be connected?

Connect each power supply to a separate power source.

Connect the primary power supply to the main source and the secondary to a backup generator.

Connect both power supplies to a power distribution unit with built-in redundancy.

Connect each power supply to a separate power source.

Connect both power supplies to a single power source.

[Maintenance and RMA Procedures]What happens to the switch operation when a supervisor module in a Cisco Nexus switch is replaced by two supervisor modules?

All modules in the switch are reset due to a stateless switchover.

The switch continues to operate without any interruption.

All modules in the switch are reset due to a stateless switchover.

Only the affected line cards reset.

The switch shuts down completely.

[Maintenance and RMA Procedures]What does OIR stand for in the context of Cisco ASR component replacement?

Offline Installation and Reboot

Operational Interface Redundancy

[Maintenance and RMA Procedures]Which action must be taken before powering down the endpoint during the replacement process of a Cisco collaboration device?

Reset the device to factory settings.

[Maintenance and RMA Procedures]What is the purpose of the pre-service checklist in the endpoint replacement process?

To ensure all necessary tools and personnel are available

To test the functionality of the existing endpoint

To verify the current configuration settings of the endpoint

To gather information about the replacement unit

[Cisco Equipment and Related Hardware]Which cable type should be used when installing replacement hardware and connecting two devices of the same type, like two DTEs or two DCEs?

RJ-45 Ethernet crossover patch cable

Rolled RJ-45 to RJ-45 console cable

RJ-45 Ethernet straight-through patch cable

RJ-45 Ethernet crossover patch cable

[Maintenance and RMA Procedures]What must be considered when installing a new fan module in a fixed-configuration Cisco Nexus switch?

The airflow direction must be consistent with other installed modules.

The size of the fan module must match the power supply.

Fan modules can be installed only when the switch is powered off

The airflow direction must be consistent with other installed modules.

The fan module must be from the same manufacturing batch as the others.

[Cisco Equipment and Related Hardware]A technician must quickly identify multiple Cisco switches in a rack without powering them on. Where should the technician look for serial numbers on the device?

Rear panel near the power supplies

Front panel near the status LEDs

Rear panel near the power supplies

[Maintenance and RMA Procedures]Which two results are achieved by briefly pressing the restore/reset button on a Cisco Meraki switch? (Choose two.)

The management interface is cleared.

A full factory restore is performed.

The management interface is cleared.

The downloaded configuration is deleted.

[Maintenance and RMA Procedures]Which step must be taken to minimize data traffic impact when replacing a fabric interconnect?

Use the fabric evacuation procedure on the subordinate fabric interconnect.

Disable high availability before replacement.

Remove all cable connections at once.

Power down both fabric interconnects simultaneously.

[Cisco Equipment and Related Hardware]Which function does the Stack Port 1 serve on a Cisco Meraki switch?

It serves as a high-speed interconnect for clustered switches.

It provides a dedicated uplink to the Meraki cloud for management.

It serves as a high-speed interconnect for clustered switches.

It connects to the Stack Port 2 of the previous switch in a stack configuration.

It connects to the Stack Port 2 of the next switch in a stack configuration.

[Safety and Electrostatic Discharge (ESD) Precautions]What is the primary reason for placing heavier devices toward the bottom of the rack when installing replacement hardware?

To facilitate easier cable management

[Cisco Equipment and Related Hardware]What are the steps to mount a Cisco device in a rack?

Install mounting brackets.Mount in rack.Ground the device.

Mount in rack.Install mounting brackets.Ground the device.

Install mounting brackets.Mount in rack.Ground the device.

Ground the device.Install mounting brackets.Mount in rack.

Install mounting brackets.Ground the device.Mount in rack.

[Cisco Equipment and Related Hardware]Which Cisco UCS management platform is specifically designed for managing standalone Cisco UCS C-Series rack servers and E-Series servers?

Cisco Integrated Management Controller

Cisco 800-150 Practice Test 2 - Free Online Exam Prep & Questions

[Cisco IOS Software Basics]

Which command is used to determine if there is sufficient space in the memory of a device before installing a new Cisco IOS image?

Become a Premium Member for full access

Unlock Premium Member

Cisco 800-150 Practice Test 2

Question

Cisco 800-150 Practice Tests

Practice Tests