ExamGecko
Home Home / HP / HPE6-A72

HP HPE6-A72 Practice Test - Questions Answers, Page 6

Question list
Search
Search

Related questions











Which two options are correct regarding the IEEE 802.11 ax standard? (Choose two.)

A.
allows transmissions of up to 4.8Gbps
A.
allows transmissions of up to 4.8Gbps
Answers
B.
is an emerging satellite connection standard to allow wireless access anywhere in the world
B.
is an emerging satellite connection standard to allow wireless access anywhere in the world
Answers
C.
operates only in the 5GHz similar to 802.11 ac
C.
operates only in the 5GHz similar to 802.11 ac
Answers
D.
operates in both the 2.4GHz and 5GHz radios bands
D.
operates in both the 2.4GHz and 5GHz radios bands
Answers
E.
is the first WLAN standard to no longer use electromagnetic signals to transmit data
E.
is the first WLAN standard to no longer use electromagnetic signals to transmit data
Answers
Suggested answer: A, D

Aruba Access Points tunnel traffic in a campus to the Mobility Controller using which protocol?

A.
Control and Provisioning of Wireless Access Points (CAPWAP)
A.
Control and Provisioning of Wireless Access Points (CAPWAP)
Answers
B.
Generic Routing Encapsulation (GRE)
B.
Generic Routing Encapsulation (GRE)
Answers
C.
Lightweight Access Point Protocol (LWAPP)
C.
Lightweight Access Point Protocol (LWAPP)
Answers
D.
Process Application Programming Interface (PAPI)
D.
Process Application Programming Interface (PAPI)
Answers
Suggested answer: B

Refer to the exhibit.

Which command will produce the above output?

A.
show interface vlan 1111
A.
show interface vlan 1111
Answers
B.
show interface gigabit 1/1/1
B.
show interface gigabit 1/1/1
Answers
C.
show vlan 1111
C.
show vlan 1111
Answers
D.
show interface 1/1/1
D.
show interface 1/1/1
Answers
Suggested answer: D

Which switch supports a maximum of 8 line-cards, 3 fabric modules, and 2 management cards?

A.
Aruba 8400
A.
Aruba 8400
Answers
B.
Aruba 8408
B.
Aruba 8408
Answers
C.
Aruba 6410
C.
Aruba 6410
Answers
D.
Aruba 5412r
D.
Aruba 5412r
Answers
Suggested answer: A

Explanation:

Reference: https ://packetpushers.net/ar uba-8400-review-2/

What is the login and password combination is used when first configuring an Aruba OS-CX switch from factory defaults?

A.
Login admin and password admin.
A.
Login admin and password admin.
Answers
B.
Login admin and password field empty.
B.
Login admin and password field empty.
Answers
C.
Login admin and password forgetmel.
C.
Login admin and password forgetmel.
Answers
D.
Login admin and password password.
D.
Login admin and password password.
Answers
Suggested answer: B

Explanation:

Reference: https://qzhls.at/blob/ldb/b/0/1/2/02b35c2be09e0616b7f0811d93Q6550f376f.pdf

What is the Link Layer Discovery Protocol?

A.
a discovery protocol used between Layer 3 devices to determine routes within a single autonomous system
A.
a discovery protocol used between Layer 3 devices to determine routes within a single autonomous system
Answers
B.
a standardized IPv6 neighbor discovery protocol used to replace the ARP and broadcast mechanism used in IPv4
B.
a standardized IPv6 neighbor discovery protocol used to replace the ARP and broadcast mechanism used in IPv4
Answers
C.
a standardized protocol for communicating directly-connected device information and capabilities.
C.
a standardized protocol for communicating directly-connected device information and capabilities.
Answers
D.
an Aruba proprietary discovery protocol supported in all Aruba switches along with Cisco Discovery Protocol or CDP
D.
an Aruba proprietary discovery protocol supported in all Aruba switches along with Cisco Discovery Protocol or CDP
Answers
Suggested answer: C

Refer to the exhibit.

What commands will successfully enable the SVI for vlan 100 on interface 1/1/1 to produce the results displayed in the command show ip interface brief in the exhibit below?

A.
Access-1(config)# interface 1/1/1Access-1(config-if)# routingAccess-1(config-if)# interface vlan 100Access-1(config-if-vlan)# ip address 10.1.1.1/24
A.
Access-1(config)# interface 1/1/1Access-1(config-if)# routingAccess-1(config-if)# interface vlan 100Access-1(config-if-vlan)# ip address 10.1.1.1/24
Answers
B.
Access-1(config)# interface 1/1/1Access-1(config-if)# vlan trunk permit vlan 100Access-1(config-if)# interface vlan 100Access-1(config-if-vlan)# ip address static 10.1.1.1/24
B.
Access-1(config)# interface 1/1/1Access-1(config-if)# vlan trunk permit vlan 100Access-1(config-if)# interface vlan 100Access-1(config-if-vlan)# ip address static 10.1.1.1/24
Answers
C.
Access-1(config)# interface vlan 100Access-1(config-if-vlan)# ip address 10.1.1.1/24
C.
Access-1(config)# interface vlan 100Access-1(config-if-vlan)# ip address 10.1.1.1/24
Answers
D.
Access-1(config-if)# vlan 100Access-1(config-vlan)# ip address 10.1.1.1/24
D.
Access-1(config-if)# vlan 100Access-1(config-vlan)# ip address 10.1.1.1/24
Answers
Suggested answer: C

What are two features in a 2-Tier design that are implemented at the Access layer? (Choose two.)

A.
VPN access
A.
VPN access
Answers
B.
WAN/MPLS connectivity
B.
WAN/MPLS connectivity
Answers
C.
Endpoint Access
C.
Endpoint Access
Answers
D.
Deep packet inspection
D.
Deep packet inspection
Answers
E.
Power over Ethernet
E.
Power over Ethernet
Answers
Suggested answer: C, E

Which network category applies to a SOHO internal network?

A.
SD-WAN
A.
SD-WAN
Answers
B.
LAN
B.
LAN
Answers
C.
WAN
C.
WAN
Answers
D.
Internet
D.
Internet
Answers
Suggested answer: D

The following command is issued:

Switch# checkpoint rollback start

What is the result?

A.
The command will fail because rollback commands must be issued from global-config mode.
A.
The command will fail because rollback commands must be issued from global-config mode.
Answers
B.
The switch will revert the running-configuration to the checkpoint called "start" without a reboot.
B.
The switch will revert the running-configuration to the checkpoint called "start" without a reboot.
Answers
C.
The command will fail because it is incomplete.
C.
The command will fail because it is incomplete.
Answers
D.
The switch will use the checkpoint "rollback" as the starting configuration on next reboot.
D.
The switch will use the checkpoint "rollback" as the starting configuration on next reboot.
Answers
Suggested answer: B
Total 88 questions
Go to page: of 9