Describe the purpose of the administrative distance

The administrative distance is used as a trust rating For route entries

Routes teamed via external BGP have a higher administrative distance than routes learned via OSPF

The administrative distance is used as a trust rating For route entries

The administrative distance for a static route is 10

The higher administrative distance is preferred

Which statement about manual switch provisioning with Aruba Central is correct?

Manual provisioning requires DHCP and does not require DNS

Manual provisioning does not require DHCP and requires DNS

Manual provisioning does not require DHCP and does not require DNS

Manual provisioning requires DHCP and does not require DNS

Manual provisioning requires DHCP and requires DNS

Where are wireless client roaming decisions made?

Joint decision made by the origination and destination APs

You are configuring a network with a stacked pair of 6300M switches used for distribution and layer 3 services. You create a new VLAN for users that will be used on multiple access stacks of CX6200 switches connected downstream of the distribution stack You will be creating multiple VLANs/subnets similar to this will be utilized in multiple access stacksWhat is the correct way to configure the routable interface for the subnet to be associated with this VLAN?

Create an SVl in the subnet on the 6300M stack.

Create a physically routed interface in the subnet on the 6300M stack for each downstream switch.

Create an SVl in the subnet on each downstream switch

Create an SVl in the subnet on the 6300M stack, and assign the management address of each downstream switch stack to a different IP address in the same subnet

Create an SVl in the subnet on the 6300M stack.

When would you bond multiple 20MHz wide 802.11 channels?

To increase throughput between the client and AP

To decrease the Signal to Noise Ratio (SNR)

To increase throughput between the client and AP

To provision highly available AP groups

To utilize high gain omni-directional antennas

You have been asked to onboard a new Aruba 6300M in a customer deployment You are working remotely rather than on-site You have a colleague installing the switch The colleague has provided you with a remote console session to configure the edge switch You have been asked to configure a link aggregation going back to the cores using interfaces 1/1/51 and 1/1/52 The Senior Engineer of the project has asked you to configure the switch and 1Q uplink with these guidelines1. Add VLAN 20 to the local VLAN database with name Mgmt2. Add L3 SVl on VLAN 20 for Management using address 10 in the 10.1.1 0/24 subnet 3. Add LAG 1 using LACP mode active for the uplink4 use vlan 20 as the native vlan on the LAG 5. Make sure the interfaces are all ON.Which configuration script will achieve the task?

Edgel# conf t vlan 20 name Mgmt interface vlan 20 ip address 10 1 1 10/24 no shut interface lag 1 shut vlan trunk native 20 vlan trunk allowed all lacp mode active Int 1/1/51.1/1/52 shut no routing lag 1 interface lag 1 no shut interface 1/1/51.1/1/52 no shut

Edge1# conf t vlan 20 name Mgmt interface vlan 20 ip address 10.1.1.10/24 no shut interface lag 1 shut vlan access 20 lacp mode active Int 1/1/51.1/1/52 shut no routing lag 1 interface lag 1 no shut

Edgel# conf t vlan 20 name Mgmt interface vlan 20 ip address 10 1.1 10/24 no shut interface 1/1/51.1/1/52 shut vlan trunk native 20 vlan trunk allowed all lag 1 lacp mode active interface 1/1/51.1/1/52 no shut

Edgel# conf t vlan 20 name Mgmt interface vlan 20 ip address 10 1 1 10/24 no shut interface lag 1 shut vlan trunk native 20 vlan trunk allowed all lacp mode active Int 1/1/51.1/1/52 shut no routing lag 1 interface lag 1 no shut interface 1/1/51.1/1/52 no shut

conf t vlan 20 name Mgmt ip address 10 1 1.10/24 no shut interface lag 1 shut vlan trunk native 1 vlan trunk allowed all lacp mode active int 1/1/51.1/1/52 shut no routing interface lag 1 no shut interface 1/1/51.1/1/52 no shut

After having configured the edge switch uplink as requested your colleague says that they have failed to ping the core You ask your colleague to verify the connection is plugged in and the switch is powered on They confirm that both are correct You attempt to ping the core switch and confirm that the ping is failing.Knowing the nature of this deployment, what commands might you use to troubleshoot this issued

Ping 10.1.1.1 - ping the core to attempt to verify connectivity show lacp agg - to verify which link aggregations are currently configured using which physical ports show lacp int - to verify the LACP status and whether any links are blocking in your topology show lldp neighors - to verify whether you are able to see the Core as an L2 neighbor to verify if the correct links are plugged in to the correct ports show run interface 1/1/51.1/1/52-to ensure the physical interfaces are no-shut and members of the lag show run interface lag 1 - to ensure the correct vlan trunking configuration is applied to the logical interface show run int vlan 20 - to ensure you have the L3 SVI no shut and configured in the correct subnet

Ping 10.11 1 - ping the core to attempt to verify connectivity Show trunk - to verify if the LAG interface was correctly added to the switch Show spanning tree - to check for spanning-tree blocked states Show port-access clients interface all - to view any port-access blocking states or failed authentication attempts on all interfaces Show run interface vlan20 - to double check the layer 3 svi configuration is correct for l_3 connectivity Show lldp neighors - to verify whether you are able to see the Core as an L2 neighbor to verify if the correct links are plugged in to the correct ports

diagnostic diag cable-diag 1/1/51 diag cable-diag 1/1/52 - to view diagnostic information for the physical link to get a status on any interruptions to Layer 1 connectivity, show ip route - to verify that the default gateway is present in the routing table show ip ospf - to check whether there is a layer 3 routing protocol enabled show ip dns - to view whether there is a valid dns source

Ping 10.1.1.1 - ping the core to attempt to verify connectivity show lacp agg - to verify which link aggregations are currently configured using which physical ports show lacp int - to verify the LACP status and whether any links are blocking in your topology show lldp neighors - to verify whether you are able to see the Core as an L2 neighbor to verify if the correct links are plugged in to the correct ports show run interface 1/1/51.1/1/52-to ensure the physical interfaces are no-shut and members of the lag show run interface lag 1 - to ensure the correct vlan trunking configuration is applied to the logical interface show run int vlan 20 - to ensure you have the L3 SVI no shut and configured in the correct subnet

Show run - to view the running configuration of the switch Show run | begin 20 'vlan 20' - to ensure VLAN 20 was correctly added to the database show run | begin 20 'interface vlan 20' - to view the L3 SVI configuration Show run interface 1/1/51.1/1/52 - to ensure the physical interfaces are no shut and were added as members of LAG 1 Show run int lag 1 - to verify LACP mode active was configured to eliminate LACP blocking states

You are in a meeting with a customer where you are asked to explain how the network redundancy feature VRRP works. What is the correct statement for this feature?

VRRP uses multicast for messaging

VRRP uses unicast for messaging

VRRP uses broadcast for messaging

Describe the functionality of ARP.

ARP maps layer-3 IP addresses to layer-2 MAC addresses.

Clients do not have an ARP cache and always ask for the default gateway.

ARP maps MAC addresses to switch ports.

ARP maps layer-3 IP addresses to layer-2 MAC addresses.

ARP uses multicast to build the ARP table.

What does a wireless client do first when its countdown timer reaches zero and it receives a Transmit Opportunity (TXOP)?

It immediately sends its Data Frames and receives an ACK from the AP.

It sends a CTS-to-self announcement to the ESP gateway.

It sends a CTS-to-self announcement to the AP and all other clients.

It sends a reassociation request frame to the AP and sends its Data Frames.

What is an advantage of using Layer 2 MAC authentication?

No setup is required on the client.

MAC allow lists are easily maintained over time.

No setup is required on the client.

It matches user names to MAC address.

MAC identifiers are hard to spoof.

The customer requires two Aruba CX 6200F 48G switches to be connected to each other with a distance of 80m/252ft between wiring closets. Switches need to have reservation for VSF expansion with ring topology in each cabinet.What is a valid configuration for a redundant link-aggregation port configuration?

Ports 1/1/51 and 1/1/52 with SFP+ for LAG

Ports 1/1/49 and 1/1/50 with SFP28 for LAG

Ports 1/1/47 and 1/1/48 for LAG

Ports 1/1/51 and 1/1/52 with SFP+ for LAG

When using the network check page in Central, what kind of tests can you run on switches? (Select two.)

A full hardware check, including a heavy memory check

How does a single Aruba CX 6300M switch configuration use L3 connectivity to establish routing traffic between switch virtual interfaces 120 and 130?

Routing is enabled by default with Aruba 6300M.

Route leaking must be configured in default VRF.

Delete 'no routing' from the SVI interfaces.

Create static routes between SVI 120 and 130.

A network technician is deploying 'headless' devices in the warehouse at the HQ location. So far, an SSID with 802.1X has been configured. However, these new devices lack 802.1X support.Which option would provide enhanced security for these devices?

Opportunistic Wireless Encryption (OWE)

What is the recommended UXI monitoring solution in large logistic facilities?

Add a UXI sensor in every aisle of the logistic space.

Use a special ruggedized UXI sensor.

Use the UXI App on all handheld devices running on Windows CE.

Add a UXI sensor in every aisle of the logistic space.

Use the UXI App direct on Zebra scanning devices running on Android.

What describes Clearpass OnGuard? (Select two.)

OnGuard is an agent, running on client systems.

OnGuard is doing posture checks on client systems.

Onguard assings an unique identity to each device.

It is used for the self-registration of guest devices.

OnGuard is an agent, running on client systems.

OnGuard is doing posture checks on client systems.

It is an intuitive portal for users to securely configure their devices.

What is the ideal mounting position for a typical Aruba indoor AP?

Horizontal, below a suspended ceiling

Horizontal, above a suspended ceiling

A network technician is testing a new SSID for a branch office. They are able to connect, get an IP address, and resolve DNS names. However, they are not able to browse the internet.On the existing SSID at the branch, connectivity to the internet works as expected on the same VLAN as the new SSID. The wireless client should have received a new role to allow internet access.What should the network technician verify to ensure both SSIDs function in a similar way?

Verify the firewall policies assigned, making sure the rules are correct and ordered properly.

Verify each SSID's authentication and encryption parameters are enabled and the same.

Verify that the implicit 'deny all' is the last entry in the firewall policies.

Verify the new SSID is broadcasting on all the APs at the branch office.

Verify the firewall policies assigned, making sure the rules are correct and ordered properly.

When does the 802.1x authentication process begin when connecting to a secured enterprise mode WLAN?

After the client completes 802.11 association

After the firewall policies are applied to the session

After the client completes 802.11 association

After the captive portal authentication completes

After the WPA 4-Way Handshake is completed

You have been asked to troubleshoot failed connectivity between a local subnet in the HQ Office and a remote subnet in the Branch Office. PC1 is unable to ping PC2.Use the provided topology and show command output to identify the reason for the failure:

On Branch Office L3-SW-2- The switch does not have a static route to the HQ Office Local Subnet.

On Branch Office - L3-SW-2- There is no Layer 3 SVI configured in the correct subnet.

On HQ Office L3-SW-1 - There is no route to the Branch Office.

On HQ Office L3-SW-1 - The switch does not have a static default route to the internet.

On Branch Office L3-SW-2- The switch does not have a static route to the HQ Office Local Subnet.

HP HPE6-A85 Practice Test 2 - Free Online Exam Prep & Questions

Spam

Selling illegal goods, money scams etc.

Hate Speech

Serious attack on a group.

Harassment and bullying

Harassing an individual (including doxing)

Harmful activities

Threatening or glorifying violence or serious harm, including self-harm

Adult content (Consensual)

Nudity/Sexual content

Sexual exploitation and abuse (child safety)

Sexually explicit or suggestive imagery or writing involving minors

Sexual exploitation and abuse (adults and animals)

Sexually explicit or suggestive imagery or writing involving non-consenting adults or non-humans

Plagiarism

Reusing content without attribution (link and blockquotes)

Poorly written

Not in English or has very bad formatting, grammar, and spelling

Inappropriate credential

Author's credential is offensive, spam, or impersonation

Other

Ex. Illegal content, incomplete question...

HP HPE6-A85 Practice Test 2

Question

HP HPE6-A85 Practice Tests

Practice Tests