What is a primary benefit of BSS coloring?

BSS color tags are applied to WI-Fi channels and can reduce the threshold tor interference

BSS color tags improve performance by allowing APS on the same channel to be farther apart

BSS color tags improve security by identifying rogue APS and tagging them as threats.

BSS color tags are applied on the wireless controllers and can reduce the threshold for interference_

BSS color tags are applied to WI-Fi channels and can reduce the threshold tor interference

With the Aruba CX 6000 24G switch with uplinks of 1/1/25 and what does the switch do when a client port detects a loop and the do-not-disabie parameter is used?

An event log message is created.

Port status will be validated once status is cleared

An event log message is created.

The network analytics engine is triggered.

Port status led blinks in amber with 100hz.

When setting up an Aruba CX VSX pair, which information does the Inter-Switch Link Protocol configuration use in the configuration created?

hello interval is 1s by default

hello interval is disabled by default

hello interval is based on the value set by dead interval

hello interval 100ms by default

hello interval is 1s by default

Your customer has four (4) Aruba 7200 Series Gateways and two (2) 7000 Series Gateways. The customer wants to form a cluster with these Gateways. What design consideration would prevent you from using all of those Gateways?

Multiple versions between Gateways in the same cluster profile are not allowed AOS 10.x.

A heterogeneous cluster is not supported in AOS 10.x.

The AP load should be lowest value of worst-case scenario load.

A combination of 7200 series and 7000 series gateways supports up to 4 nodes

You are deploying Aruba CX 6300's with the customers requirement to only allow one (1) VoIP phone and one (1) device.The following local role gets assigned to the phone port-access rote VoIP device-traffic-class voiceWhat set of commands best fits this requirement?

interface 1/1/1 aaa authentication port-access client-limit multi-domain 2 aaa authentication port-access auth-mode multi-domain

interface 1/1/1 aaa authentication port-access client-limit 2 aaa authentication port-access auth-mode client-mode

interface 1/1/1 aaa authentication port-access auth-mode multi-domain

interface 1/1/1 aaa authentication port-access client-limit multi-domain 2 aaa authentication port-access auth-mode multi-domain

interface 1/1/1 aaa authentication port-access client-limit 1 aaa authentication port-access auth-mode device-mode

You are building a configuration in Central that will be used for a standardized network design for small sites for your company, you want to use GUI configuration for gateways and Aps, while template configuration for switches. You need to align with Aruba best practices.Which set of actions will satisfy these requirements?

Create a single group in Central. Create a unique site for each location, and assign devices to the appropriate site.

Create one group in Central for switches a second group for APs. and a third group for gateways Create a unique site for each location, and assign devices to the appropriate site.

Create one group in Central for switches and a second group for APs and gateways. Create a unique site for each location, and assign devices to the appropriate site.

Create a single group in Central. Create a unique site for each location, and assign devices to the appropriate site.

Create a single group in Central. Create a unique site for each type of device, and assign devices to the appropriate site.

Which statements are true regarding a VXLAN implementation on Aruba Switches? (Select two.)

MTU size must be increased beyond the default

VNIs encapsulate and decapsulate VXLAN traffic

MTU size must be increased beyond the default

VNIs encapsulate and decapsulate VXLAN traffic

VTEPs encapsulate and decapsulate VXLAN traffic

They are only available for datacenter switches (CX 8k, 9k,10k)

All Aruba CX switches support VXLAN.

A customer is concerned about me unprotected traffic between an AOS-CX switch and a gateway, running on AOStO. What is a feasible option to protect this traffic?

Implement an IPSec tunnel to protect PAPI between the AOS-CX switches and the gateway

Implement an MD5 HMAC function lo protect PAPI between the AOS-CX switches and the gateway

Implement a GRE tunnel to protect PAPI between the AOS-CX switches and the gateway

no action is needed, an RSA certificate already encrypts the traffic

What does the 802.3bz standard describe?

AP directed roaming between APs

When configuring UBT on a switch what will happen when a gateway role is not specified?

The switch will put the client on the access VLAN

The gateway will assign a default role to the client

The switch will assign the default deny role to the client.

The gateway will send back the deny role to the client.

Your customer currently has Iwo (2) 5406 modular switches with MSTP configured as their core switches. You are proposing a new solution. What would you explain regarding the Aruba CX VSX switch pair when the Primary VSX node is replaced and the system MAC is replaced?

During the initial VSX configuration, the system-mac is assigned with a fixed MAC based on VSX ID.

VSX will select the MAC address from a node that is the lower ID.

Configure vMAC on the Primary VSX node under VSX to retain MAC after hardware replacement.

VSX will select the MAC address from a node that is a higher ID.

During the initial VSX configuration, the system-mac is assigned with a fixed MAC based on VSX ID.

With the Aruba CX 6100 48G switch with uplinks of 1/1/47 and 1/1/48. how do you automate the process of resuming the port operational state once a loop on a client port is cleared?

Configure int 1/1/1-1/1/46 loop-protect re-enable-timer.

Configure int 1/1/1-1/1/52 loop-protect disable timer.

Configure global loop-protect disable timer.

Configure int 1/1/1-1/1/46 loop-protect re-enable-timer.

Configure global loop-protect re-enable-timer.

Refer to Exhibit: A company has deployed 200 AP-635 access points. To take advantage of the 6 GHz band, the administrator has attempted to configure a new WPA3-OWE SSID in Central but is not working as expected.What would be the correct action to fix the issue?

Change the SSID to WPA3-Enhanced Open.

Change the SSID to WPA3-Enterprise (CNSA).

Change the SSID to WPA3-Personal.

Change the SSID to WPA3-Enhanced Open.

Change the SSID to WPA3-Enterprise (CCM).

A company recently upgraded its campus switching infrastructure with Aruba 6300 CX switches. They have implemented 802.1X authentication on edge ports where laptop and loT devices typically connect An administrator has noticed that for PoE devices the pons are delivering the maximum wattage instead of what the device actually needs Upon connecting the loT devices, the devices request their specific required wattage through information exchange

Create device profiles with the correct power definitions.

Concerned about this waste of electricity, what should the administrator implement to solve this problem?

Enable AAA authentication to exempt LLDP and/or CDP information

Globally enable the QoS trust setting for LLDP and/or CDP

Create device profiles with the correct power definitions.

implement a classifier policy with the correct power definitions.

Your manufacturing client is deploying two hundred wireless IP cameras and fifty headless scanners in their warehouse. These new devices do not support 802.1X authentication.How can HPE Aruba enhance security for these new IP cameras in this environment?

MPSK provides for each device in the WLAN to have its own unique pre-shared Key.

Use MPSK Local to automatically provide unique pre-shared Keys for devices.

Aruba ClearPass performs the 802.1X authentication and installs a certificate.

MPSK provides for each device in the WLAN to have its own unique pre-shared Key.

MPSK Local will allow the cameras to share a rey and the scanners to share a different

You are working on a network where the customer has a dedicated router with redundant Internet connections Tor outbound high-importance real-time audio streams from their datacenter All of this traffic.* originates from a single subnet* uses a unique range of UDP ports* is required to be routed to the dedicated routerAll other traffic should route normally The SVI for the subnet containing the servers originating the traffic is located on the core routing switch in the datacenter What should be configured?

Configure Policy Based Routing (PBR) on the core routing switch for the VRF with the servers' SVI

Configure a new OSPF area including both the core routing switch and the dedicated router

Configure a BGP link between the core routing switch and the dedicated router and route filtering.

Configure Policy Based Routing (PBR) on the core routing switch for the VRF with the servers' SVI

Configure a dedicated VRF on the core routing switch and make the dedicated router the default route.

A customer just upgraded aggregation layer switches and noticed traffic dropping for 120 seconds after the aggregation layer came online again. What is the best way to avoid having this traffic dropped given the topology below?

Configure the linkup delay timer to include LAGs 101 and 102, which will allow time for routing adjacencies lo form and to learn upstream routes

Configure the linkup delay timer to 240 seconds to double the amount of lime for the initial phase to sync

Configure the linkup delay timer to exclude LAGS 101 and 102, which will allow time for routing adjacencies to form and to learn upstream routes

Configure the linkup delay timer to include LAGs 101 and 102, which will allow time for routing adjacencies lo form and to learn upstream routes

Configure the linkup delay timer to 120 seconds, which will allow the right amount of time for the initial phase to sync

HP HPE7-A01 Practice Test 3 - Free Online Exam Prep & Questions

With the Aruba CX switch configuration, what is the Active Gateway feature that is used for and is unique to VSX configuration?

Become a Premium Member for full access

Unlock Premium Member

HP HPE7-A01 Practice Test 3

Question

HP HPE7-A01 Practice Tests

Practice Tests