Which two statements about firewall filters are correct? (Choose two.)

Firewall filters are stateless.

Firewall filters can match Layer 4 parameters.

Firewall filters are stateless.

Firewall filters can match Layer 7 parameters.

Firewall filters can match Layer 4 parameters.

You have configured some interfaces on a Junos device; however, you have not yet committed the configuration.What happens if you issue the rollback 0 command in this scenario?

The interface changes you made are discarded.

The messages.log file is deleted.

The factory default configuration is loaded.

The interface changes you made are discarded.

You want to redeploy a Junos device by clearing the existing configuration and resetting it to factory defaults.In this scenario, which command would help to accomplish this task?

request system storage cleanup dry-run

By default, how does the PFE manage unicast traffic destined for an existing forwarding table entry?

It sends the traffic through one port toward its destination.

It sends the traffic through multiple ports toward its destination.

It sends the traffic through one port toward its destination.

It sends the traffic through the f xpl interface to the RE.

It sends all traffic to the control plane for further processing.

Which protocol is responsible for learning an IPv4 neighbor's MAC address?

Address Resolution Protocol (ARP)

Network Address Translation (NAT)

Media Access Control Security (MACsec)

Neighbor Discovery Protocol (NDP)

Exhibitpolicy-options { policy-statement Load-Balance-Policy { term Load-Balance { then { load-balance per-flow; accept;}}}}routing-options {router-id 192.168.100.11; autonomous-system 65201; forwarding-table {export Load-Balance-Policy;Referring to the exhibit, which two statements are correct? (Choose two.)

The policy enables equal cost load balancing in the forwarding table.

The policy must be applied under the protocols hierarchy.

The policy enables per-packet load balancing.

The policy enables flow-based load balancing.

Exhibit. Referring to the exhibit, which routing configuration is required for these two users to access the remote server?

Users and the server require a default gateway.

Users must connect directly to the router.

Users and the server require a default gateway.

Trunk ports must be enabled on the switch.

A routing protocol must be enabled on the router.

Which criteria does the Junos OS use to select an active route when two entries exist in the routing table?

the route with the lowest preference number

the most recently learned dynamic route

the route with the highest preference number

the route with the highest metric

Which two functions are performed by the PFE? (Choose two.)

It implements firewall filters.

It maintains the routing table.

Exhibituser@router> show route 192.168.36.1inet.O: 5 destinations, 6 routes (5 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both192.168.36.1/32 *[Static/5] 00:00:31> to 10.1.1.2 via ge-0/0/10.0 [OSPF/IO] 00:02:21, metric 1 > to 10.1.1.2 via ge-0/0/10.0Referring to the exhibit, which route(s) will be selected by Junos for packet forwarding?

The static route will be selected.

The OSPF route will be selected.

The static route will be selected.

The Junos OS randomly selects one route.

The Junos OS selects both routes.

What are two functions of the Routing Engine? (Choose two.)

It processes all management traffic.

It runs the Junos operating system.

It processes all management traffic.

It runs the Junos operating system.

It evaluates firewall filters for transit traffic.

Which statement is correct when multiple users are configuring a Junos device using the configure private command?

Each user gets their own candidate configuration.

A commit by any user will commit changes made by all active users.

A commit will not succeed until there is only a single user in configuration mode.

Each user gets their own candidate configuration.

Each user shares the same candidate configuration.

You are logged in to a Junos OS device with SSH and issued the show protocols | compare command in the configuration, but no output is shown.Which statement is correct in this scenario?

There are no changes to the candidate configuration.

The command only works for interface configuration differences.

There are no changes to the candidate configuration.

Someone accidentally deleted the active configuration.

You must commit the configuration before any output will be shown.

Which two statements apply to the Routing Engine functions? (Choose two.)

It responds to ping and traceroute commands.

It maintains the routing tables.

It responds to ping and traceroute commands.

It maintains the routing tables.

It does not process routing updates.

It processes the transit traffic.

Which two actions happen when multiple users issue the configure exclusive command to enter configuration mode on a Junos device? (Choose two.)

The candidate configuration is locked.

Other users cannot enter configuration mode.

Other users can enter configuration mode.

The candidate configuration is unlocked.

The candidate configuration is locked.

Other users cannot enter configuration mode.

Which statement is correct concerning exception traffic processing?

Exception traffic is rate-limited to protect the RE.

Exception traffic is always dropped during congestion.

Exception traffic is rate-limited to protect the RE.

Exception traffic is discarded by the PFE.

Exception traffic is never forwarded.

Which two statements are correct about a Routing Engine? (Choose two.)

It processes management traffic.

It processes CoS marked traffic.

It processes management traffic.

Which two statements are correct regarding Layer 2 network switches? (Choose two.)

Switches are susceptible to traffic loops.

Switches flood broadcast traffic.

Switches create a single collision domain.

Switches are susceptible to traffic loops.

Switches flood broadcast traffic.

Switches do not learn MAC addresses.

What does the user@router> clear log ospf-trace command accomplish?

Data in the ospf-trace file is removed and logging continues.

Logging data into ospf-trace is stopped.

Trace parameters are removed from the OSPF protocol configuration.

Data in the ospf-trace file is removed and logging continues.

The ospf-trace file is deleted.

Your router has a route to the 10.1.1.0/24 network with a next hop of r jet.In this scenario, which action will your router perform when traffic destined to the 10.1.1.0/24 network is received?

The traffic will be silently discarded.

The traffic will be discarded and an ICMP unreachable message will be sent to the destination of the traffic.

The traffic will be discarded and an ICMP unreachable message will be sent to the source of the traffic.

The traffic will be redirected using a default route.

The traffic will be silently discarded.

Juniper JN0-105 Practice Test 2 - Free Online Exam Prep & Questions

What is the protocol data unit (PDU) of the Data Link Layer?

segment

byte

frame

bit

Comment (0)

Juniper JN0-105 Practice Test 2

Question

Juniper JN0-105 Practice Tests

Practice Tests