Which statement is correct about the IS-IS ISO NET address?

An ISO NET address must be unique for each device in the network.

An ISO NET address defined with a system ID of 0000.0000.0000 must be selected as the DIS.

An ISO NET address must be unique for each device in the network.

You can only define a single ISO NET address per device.

The Area ID must match on all devices within a L2 area.

Which two statements are correct about generated routes? (Choose two.)

Generated routes require a contributing route.

Generated routes show a next hop in the routing table.

Generated routes require a contributing route.

Generated routes show a next hop in the routing table.

Generated routes appear in the routing table as static routes

Generated routes cannot be redistributed into dynamic routing protocols.

Exhibit. You want to enable redundancy for the EBGP peering between the two routers shown in the exhibit. Which three actions will you perform in this scenario? (Choose three.)

Configure loopback interface peering.

Configure routes for the peer loopback interface IP addresses.

Configure loopback interface peering.

Configure routes for the peer loopback interface IP addresses.

Configure an MD5 peer authentication.

Which two statements about redundant trunk groups on EX Series switches are correct? (Choose two.)

Layer 2 control traffic is permitted on the secondary link.

If the active link fails, then the secondary link automatically takes over.

Redundant trunk groups use spanning tree to provide loop-free redundant uplinks.

Redundant trunk groups load balance traffic across two designated uplink interfaces.

Layer 2 control traffic is permitted on the secondary link.

If the active link fails, then the secondary link automatically takes over.

Which two statements are correct about using firewall filters on EX Series switches? (Choose two.)

You can deploy only stateless firewall filters on an EX Series switch.

You can apply firewall filters to both Layer 2 and Layer 3 traffic on an EX Series switch.

You can deploy only stateless firewall filters on an EX Series switch.

You can only apply firewall filters to Layer 2 traffic on an EX Series switch.

You can apply firewall filters to both Layer 2 and Layer 3 traffic on an EX Series switch.

You can deploy both stateless and stateful firewall filters on an EX Series switch.

You want to use filter-based forwarding (FBF) on your Internet peering router to load-balance traffic to two directly connected ISPs based on the source address.Which two statements are correct in this scenario? (Choose two.)

FBF uses the forwarding routing instance type.

RIB groups are used to copy routes from the inet. o routing table.

FBF uses the no-forwarding routing instance type.

FBF uses the forwarding routing instance type.

RIB groups are used to copy routes from the inet. o routing table.

RIB groups are used to hide routes in the inet. 0 routing table.

You want to ensure traffic is routed through a GRE tunnel.In this scenario, which two statements will satisfy this requirement? (Choose two.)

Tunnel endpoints must have a route that directs traffic into the tunnel.

All intermediary devices must have a route to the tunnel endpoints.

Tunnel endpoints must have a route that directs traffic into the tunnel.

All intermediary devices must have a route to the tunnel endpoints.

Keepalives must be used on stateless tunneling protocols.

BFD must be used on the stateless tunneling protocols.

Exhibit You are troubleshooting an issue where traffic to 192.168.10.0/24 is being sent to R1 instead of your desired path through R2.Referring to the exhibit, what is the reason for the problem?

R1's route is the best path due to a higher local preference

R2's route is not the best path due to loop prevention.

R2's route is not the best path due to a lower origin code.

R1's route is the best path due to a higher local preference

R1's route is the best path due to the shorter AS path.

Which statement is correct about the storm control feature?

The storm control feature is enabled in the factory-default configuration on EX Series switches.

The storm control feature requires a special license on EX Series switches.

The storm control feature is not supported on aggregate Ethernet interfaces.

The storm control configuration only applies to traffic being sent between the forwarding and control plane.

After receiving a BGP route, which two conditions are verified by the receiving router to ensure that the received route is valid? (Choose two)

The AS-path length is greater than 0.

The local preference is greater than 0.

What are two reasons for creating multiple areas in OSPF? (Choose two.)

to reduce LSA flooding across the network

to increase the number of adjacencies in the backbone

to increase the size of the LSDB

to reduce LSA flooding across the network

Which two events cause a router to advertise a connected network to OSPF neighbors? (Choose two.)

When an OSPF adjacency is established.

When a static route to the 224.0.0.5 address is created.

When an OSPF adjacency is established.

When an interface has the OSPF passive option enabled.

When a static route to the 224.0.0.6 address is created.

When a static route to the 224.0.0.5 address is created.

You are an operator for a network running 1S-IS. Two routers are failing to form an adjacency. What are two reasons for this problem? (Choose two.)

There is no configured ISO address on any IS-IS interface.

The family iso configuration is missing from the adjacency interface.

There are mismatched router IDs on the L2 routers.

There is no configured ISO address on any IS-IS interface.

There is a mismatched area ID between the L2 routers.

The family iso configuration is missing from the adjacency interface.

You have DHCP snooping enabled but no entries are automatically created in the snooping database for an interface on your EX Series switch. What are two reasons for the problem? (Choose two.)

MAC limiting is enabled on the interface.

The device that is connected to the interface has a static IP address.

The device that is connected to the interface has performed a DHCPRELEASE.

MAC limiting is enabled on the interface.

The device that is connected to the interface has a static IP address.

Dynamic ARP inspection is enabled on the interface.

You implemented the MAC address limit feature with the shutdown action on all interfaces on your switch.In this scenario, which statement is correct when a violation occurs?

By default, you must manually clear the violation for the interface to send and receive traffic again.

By default, the violation will automatically be cleared after 300 seconds and the interface will resume sending and receiving traffic for all learned devices.

By default, devices that are learned before the violation occurs are still allowed to send and receive traffic through the specific interface.

By default, the interface will continue to send and receive traffic for all connected devices after a violation has occurred.

An update to your organization's network security requirements document requires management traffic to be isolated in a non-default routing-instance. You want to implement this requirement on your Junos-based devices.Which two commands enable this behavior? (Choose two.)

set system management---instance

set routing---instances mgmt_junos

set routing---instances mgmtjunoa interface ge-0/0/0.0

set routing---instances mgmt_junos interface em1

set system management---instance

set routing---instances mgmt_junos

Exhibit Referring to the exhibit, which statement is correct?

The local device is the root bridge for this RSTP topology.

The local device is using a bridge priority of 4k.

The root bridge is using a bridge priority of 4k.

The root bridge has not been elected for this RSTP topology.

The local device is the root bridge for this RSTP topology.

Which statement about aggregate routes is correct?

Aggregate routes are used for advertising summarized network prefixes.

Aggregate routes can only be used for static routing but not for dynamic routing protocols.

Aggregate routes are automatically generated for all of the subnets in a routing table.

Aggregate routes are always preferred over more specific routes, even when the specific routes have a better path.

Aggregate routes are used for advertising summarized network prefixes.

Exhibit Referring to the exhibit, which two configuration changes must you apply for packets to reach from R1 to R3 using IS-IS? (Choose two.)

On R1, enable Level 1 on the ge-0/0/1 interface.

On R3 enable Level 1 on the ge-0/0/4 interface

On R1, enable Level 1 on the ge-0/0/1 interface.

On R3 disable Level 2 on the ge-0/0/4 interface.

On R1, disable Level 2 on the ge-0/0/1 interface.

On R3 enable Level 1 on the ge-0/0/4 interface

You are receiving multiple BGP routes from an upstream neighbor and only want to advertise a single summarized prefix to your internal OSPF neighbors. This route should only be advertised when you are receiving these BGP routes from this neighbor.In this scenario, which type of route should you create?

static route using the resolve feature

static route using qualified next hops

Juniper JN0-351 Practice Test 2 - Free Online Exam Questions 41-65

Which two statements about BGP facilitate the prevention of routing loops between two autonomous systems? (Choose two.)

Become a Premium Member for full access

Unlock Premium Member

Juniper JN0-351 Practice Test 2

Question

Drag and Drop

Hot Area

Juniper JN0-351 Practice Tests

Practice Tests