Refer to the exhibit.The profile shown in the exhibit is assigned to a group of managed FortiSwitch ports. and these ports are connected to endpoints which are powered by PoE. Which configuration action can you perform on the LLDP profile to cause these endpoints to exchange PoE information and negotiate power with the managed FortiSwitch?

Add power management as part of LLDP-MED TLVs to advertise.

Assign a new LL0P profile to handle different LLDP-ME0 TLVs

Add power management as part of LLDP-MED TLVs to advertise.

Define an LLDP-ME0 location 10 to use standard protocols for power.

Create new a LLOP-MEO application type to define the PoE parameters.

What can an administrator do to maintain the existing standalone FortlSwltch configuration while changing the management mode to FortLink?

Enable the Forti-link setting on FortiSwitch before the authorization process

Use a migration tool based on python script to convert the configuration

Enable the Forti-link setting on FortiSwitch before the authorization process

FortiGate will automatically save the existing FortiSwitch configuration during the Forti-link management process.

Register FortiSwitch to For1ISwitch Cloud to save a copy before managing by Forti-Gate.

Exhibit. Two routes are not installed in the forwarding information base (FIB) as shown in the exnibit. Which two statements about these two route entries are true? (Choose two.)

These two routes have a higher administrative distance value available to the destina-tion networks.

These two routes will become primary, if the best routes are removed.

These two routes have a higher administrative distance value available to the destina-tion networks.

These two routes will become primary, if the best routes are removed.

These two routes will be used as load-balancing routes.

These two routes are available in the hardware routing table.

Exhibit. Which configuration change will allow the managed FortiSwitch to accept SNMP requests from any source?

Configure an SNMP host to send SNMP traps.

Create a new local access profile for SNMP only.

Enable SNMP on the internal interface of the switch.

Configure an SNMP host to send SNMP traps.

Add SNMP service on the management interface of the switch.

In which two ways can you assign a FortiSwitch port to a VDOM using multi-tenancy setup? (Choose two.)

Create a virtual port pool on the FortiGate CLI.

Assign a port to a VDOM directly on the managed FortiSwitch.

Switch the FortiLink interface to the target VDOM.

Remove the managed FortiSwitch and allocate ports directly on FortiSwitch.

Create a virtual port pool on the FortiGate CLI.

Assign a port to a VDOM directly on the managed FortiSwitch.

Which statement about the use of the switch port analyzer (SPAN) packet capture method is true?

Traffic on the management interface can be mirrored and captured by the monitoring device.

Mirrored traffic can be sent across multiple switches.

SPAN can be configured only on a standalone FortiSwitch.

Traffic on the management interface can be mirrored and captured by the monitoring device.

The monitoring device must be connected to the same switch where the traffic is being mirrored

What is the role of a device that is simultaneously functioning as both the distribution and core in the hierarchy network model?

POE with high density FortiSwitch

FortiSwitch functioning as standalone

HA backup FortiGate managing FortiSwitch

Which statement about the IGMP snooping querier when enabled on a VLAN is true?

All other indirectly connected switches will be unable to get IGMP multicast traffic.

Active multicast receiver entries are aging on each IGMP query sent on the VLAN

IGMP reports on the VLAN are forwarded to all switch ports.

The setting can only be enabled using the FortiSwitch CLI.

All other indirectly connected switches will be unable to get IGMP multicast traffic.

Exhibit. You need to manage three FortiSwitch devices using a FortiGate device. Two of the FortiSwitch devices initiated a reboot after the authorization process. However, the FortiSwitch device with the configuration shown in the exhibit. did not reboot All three devices completed FortiLink manage-ment authorization successfully.Why did the FortiSwitch device shown in the exhibit not reboot to complete the authorization pro-cess?The management mode was set to use FortiLink mode.

The management mode was set to use FortiLink mode.

Switch auto-discovery is enabled.

The management mode was set to use FortiLink mode.

The FortiSwitch device is scheduled to reboot as part the authorization process

The system time is not in-sync and is using a non-default value

Exhibit. The exhibit shows the current status of the ports on the managed FortiSwitch.Access-1.Why would FortiGate display a serial number in the Native VLAN column associated with the port23 entry?

Ports connect to adjacent FortiSwitch devices will show their.serial number as the na-tive VLAN

Port23 is a member of a trunk that uses the Access-1 FortiSwitch senal number as the name of the trunk.

Port23 is configured as the dedicated management interface.

A standalone switch with the showm serial number is connected on por123.

Ports connect to adjacent FortiSwitch devices will show their.serial number as the na-tive VLAN

Exhibit. port1 and port2 are the only ports configured with the same native VLAN 10.What are two reasons that can trigger port1 to shut down? (Choose two.)

Loop guard frame sourced from port 1 was received VLAN 10 ports.

Oport1 was shut down by loop guard protection.

Loop guard frame sourced from port 1 was received VLAN 10 ports.

STP triggered a loop and applied loop guard protection on port1.

Oport1 was shut down by loop guard protection.

An endpoint sent BPDU on port1 it received from another interface.

Exhibit. What conditions does a FortiSwitch need to have to successfully configure the options shown in the exhibit above? (Choose two.)

The FortiSwitch model is equipped with a maximum of 54 interfaces.

The CLI commands are enabling a splitpo rt into four 10Gbps interfaces.

The FortiSwitch model is equipped with a maximum of 54 interfaces.

The CLI commands are enabling a splitpo rt into four 10Gbps interfaces.

The port full speed prior the split was 100G SFP+

The split port can be assigned to native VLAN

Which two statements about DHCP snooping enabled on a FortiSwitch VLAN are true? (Choose two.)

By default, all FortiSwitch ports are set to forward client DHCP requests to untrusted ports.

Settings related to DHCP option 82 are only configurable through the CLI

Enabling DHCP snooping on a FortiSwitch VLAN ensures requests and replies are seen by all DHCP servers.

switch-controller-dhcp-snooping-verify-mac verifies the destination MAC address to protect against DHCP exhaustion attacks.

By default, all FortiSwitch ports are set to forward client DHCP requests to untrusted ports.

Settings related to DHCP option 82 are only configurable through the CLI

Which statement about using MAC, IP, and protocol-based VLANs on FortiSwitch is true?

It provides benefits that can be obtained when using 802.1X authentication.

lt is a scalable and secure solution in comparison to other Layer 2 security measures.

FortiSwitch uses only the Ethernet type to assign traffic to VLANs.

It provides benefits that can be obtained when using 802.1X authentication.

Endpoints are required to use the same FortiSwitch port to remain members of the VLAN.

Fortinet NSE6_FSW-7.2 Practice Test 2 - Free Online Exam Prep & Questions

FortiGate is unable to establish a tunnel with the FortiSwitch device it is supposed to manage Based on the debug output shown in the exhibit, what is the reason for the failure?

Become a Premium Member for full access

Unlock Premium Member

Fortinet NSE6_FSW-7.2 Practice Test 2

Question

Fortinet NSE6_FSW-7.2 Practice Tests

Practice Tests