Home

Home / DELL / D-PSC-MN-01

Question list

List of questions

Question 1

(0)

What are the required settings when using terminal emulation software to connect to a Dell EMC PowerScale Gen 5 node?

Question 2

(0)

A platform engineer is creating a Dell PowerScale cluster that must meet SEC 17a-4f rules. Node 1 is powered on and cabled. What action must be taken to meet the requirement?

Question 3

(0)

A customer wants to add SSDs to the drive sleds in a Dell PowerScale H600 node for higher storage performance. What should the platform engineer tell the customer?

Question 4

(0)

A customer received replacement parts from Dell without prior communication. Why did they receive the replacement parts?

Question 5

(0)

What is a consideration when reimaging a Dell PowerScale node?

Question 6

(0)

Which cable is required to connect to the A300 console?

Question 7

(0)

A customer has a Dell EMC PowerScale cluster. The IT manager asks a platform engineer if WORM directories can be overwritten.

Question 8

(0)

A platform engineer has created a cluster of 8 F200 nodes. A requirement is for each power supply on each node to supply power to the respective node equally. What must the platform engineer do to

Question 9

(0)

A platform engineer has added an F200 node to a Dell EMC PowerScale cluster. The cluster now has five F200 nodes. Before leaving the site, what action must the engineer perform?

Question 10

(0)

What should the platform engineer pre-check when installing Dell EMC PowerScale Gen 6 nodes in a customer-provided rack?

Open VPLUS File

Convert VPLUS to PDF

Related questions

A platform engineer needs to swap an NVDIMM battery. What prerequisite conditions are required to prevent data loss when removing the NVDIMM battery?

Exhibit. A platform engineer has connected power cables to a Dell PowerScale Gen6 node. What does the status indicator indicate?

Which cable is required to connect to the A300 console?

A customer received replacement parts from Dell without prior communication. Why did they receive the replacement parts?

A customer wants to add SSDs to the drive sleds in a Dell PowerScale H600 node for higher storage performance. What should the platform engineer tell the customer?

What is a consideration when reimaging a Dell PowerScale node?

Refer to the exhibit. An engineer replaced the drive in C1. They run the isi devices drive list command and obtain the output that is shown. What action must the engineer take?

An existing PowerScale cluster consists of four A300 and three F600 nodes. What is the minimum number of nodes an engineer can add to expand both node pools?

What are the required settings when using terminal emulation software to connect to a Dell EMC PowerScale Gen 5 node?

A platform engineer is tasked with adding F600 nodes to an existing Dell EMC PowerScale cluster. After racking and stacking the F600 nodes, they determine that the cluster contains X210 and H400 nodes. What should the platform engineer consider?

Question 99 - D-PSC-MN-01 discussion

Report

What accurately describes the InfiniBand cable support?

A.

Supports QSFP to QSFP cabling only

B.

Supports QSFP to QSFP cabling or QSFP to CX4 cabling

C.

Supports QSFP to CX4 cabling only

D.

Supports front-end customer external traffic

Suggested answer: A

Explanation:

In Dell EMC PowerScale systems that use InfiniBand for back-end networking, the cabling standards are specific to ensure optimal performance and compatibility.

InfiniBand Cable Support:

QSFP to QSFP Cabling Only:

QSFP (Quad Small Form-factor Pluggable):

A compact, hot-pluggable transceiver used for high-speed InfiniBand networking.

Standard for PowerScale:

PowerScale systems utilizing InfiniBand support QSFP to QSFP cables exclusively.

Ensures high-bandwidth, low-latency communication between nodes.

Why Option A is Correct:

Exclusive Support:

QSFP to QSFP is the only supported cabling method for InfiniBand in these systems.

Compatibility and Performance:

Using QSFP to QSFP cables guarantees compatibility with node interfaces and optimal network performance.

Why Other Options Are Incorrect:

Option B (QSFP to QSFP or QSFP to CX4):

QSFP to CX4 is not supported; CX4 is an older connector type not compatible with current PowerScale InfiniBand configurations.

Option C (QSFP to CX4 only):

Incorrect, as QSFP to CX4 cabling is not used in PowerScale systems for InfiniBand.

Option D (Supports front-end customer external traffic):

InfiniBand is used for internal back-end networking, not for front-end external customer traffic, which uses Ethernet connections.

Dell PowerScale

Reference:

Dell EMC PowerScale Networking Guide:

Back-End Network Cabling Section:

Specifies the use of QSFP to QSFP cables for InfiniBand connectivity.

Supported Cable Types:

Lists the approved cables and transceivers for InfiniBand networks.

Hardware Installation Guides:

Provide detailed instructions and diagrams for cabling using QSFP to QSFP connections.

Best Practices:

Use Certified Cables:

Always use Dell EMC-approved QSFP to QSFP cables to ensure reliability.

Proper Installation:

Follow the recommended procedures for connecting and securing InfiniBand cables.

Cable Management:

Organize cables to prevent strain and maintain proper airflow.

Additional Notes:

InfiniBand Usage:

Provides high-speed communication between nodes for data replication and cluster operations.

Transition to Ethernet:

Newer PowerScale models may use Ethernet back-end networking instead of InfiniBand.

Show Answer

asked 29/10/2024

Jeffrey Holt Jr

26 questions

User

Your answer: A B C D

0 comments

Sorted by

Leave a comment first