ExamGecko
Search Search Login
Home Home / Fortinet / NSE7_EFW-7.2
Question list
Search
Search

List of questions

Search
Open VPLUS File
Convert VPLUS to PDF

Related questions

Refer to the exhibit, which shows two configured FortiGate devices and peering over FGSP. The main link directly connects the two FortiGate devices and is configured using the set session-syn-dev <interface> command. What is the primary reason to configure the main link?
Which, three conditions are required for two FortiGate devices to form an OSPF adjacency? (Choose three.)
Exhibit. Refer to the exhibit, which contains a partial policy configuration. Which setting must you configure to allow SSH?
Which FortiGate in a Security I auric sends togs to FortiAnalyzer?
Exhibit. Refer to the exhibit, which shows information about an OSPF interlace What two conclusions can you draw from this command output? (Choose two.)
Refer to the exhibits, which contain the network topology and BGP configuration for a hub. Exhibit A. Exhibit B. An administrator is trying to configure ADVPN with a hub and spoke VPN setup using iBGP. All the VPNs are up and connected to the hub. The hub is receiving route information from both spokes over iBGP; however the spokes are not receiving route information from each other. What change must the administrator make to the hub BGP configuration so that the routes learned from one spoke are forwarded to the other spoke?
Refer to the exhibit. which contains a partial configuration of the global system. What can you conclude from this output?
Which two statements about metadata variables are true? (Choose two.)
Refer to the exhibit, which shows a network diagram. Which IPsec phase 2 configuration should you impalement so that only one remote site is connected at any time?
Refer to the exhibit, which contains a partial OSPF configuration. What can you conclude from this output?

Question 46 - NSE7_EFW-7.2 discussion

Report
Export

Refer to the exhibit, which shows two configured FortiGate devices and peering over FGSP.

The main link directly connects the two FortiGate devices and is configured using the set session-syn-dev <interface> command.

What is the primary reason to configure the main link?

A.
To have both sessions and configuration synchronization in layer 2
Answers
A.
To have both sessions and configuration synchronization in layer 2
B.
To load balance both sessions and configuration synchronization between layer 2 and 3
Answers
B.
To load balance both sessions and configuration synchronization between layer 2 and 3
C.
To have only configuration synchronization in layer 3
Answers
C.
To have only configuration synchronization in layer 3
D.
To have both sessions and configuration synchronization in layer 3
Answers
D.
To have both sessions and configuration synchronization in layer 3
Suggested answer: D

Explanation:

The primary purpose of configuring a main link between the devices is to synchronize session information so that if one unit fails, the other can continue processing traffic without dropping active sessions.

A. To have both sessions and configuration synchronization in layer 2. This is incorrect because FGSP is used for session synchronization, not configuration synchronization.

B. To load balance both sessions and configuration synchronization between layer 2 and 3. FGSP does not perform load balancing and is not used for configuration synchronization.

C. To have only configuration synchronization in layer 3. The main link is not used solely for configuration synchronization.

D. To have both sessions and configuration synchronization in layer 3. The main link in an FGSP setup is indeed used to synchronize session information across the devices, and it operates at layer 3 since it uses IP addresses to establish the peering.


Show Answer
asked 18/09/2024
Eduardo Bravo
38 questions
PreviousPreviousNextNext
User
Your answer:
0 comments
Sorted by

Leave a comment first

ExamGecko

Copyright @2023 ExamGecko | All right reserved

Mail us: [email protected]
About us
Contact us
Twitter X
Facebook
Medium
Convert VPLUS to PDF
Open VPLUS files Easily and Quickly
Privacy Policy
Disclaimer
Terms