Home / ISTQB / CTFL4

Question list

List of questions

Question 1

(0)

Which of the following statements about re-testing and regression testing are TRUE? I Re-testing should be performed after a defect is fixed. II Regression testing should always be performed after

Question 2

(0)

Which of the following can be considered a VALID exit criterion? I Estimates of defect density or reliability measures. II . The completion and publication of an exhaustive Test Report. III . Acc

Question 3

(0)

Which of the following s the most correct statement about state testing techniques?

Question 4

(0)

A test manager decided to skip static testing since he believes bugs can be found easily by doing dynamic testing. Was this decision right or wrong?

Question 5

(0)

In which of the following test documents would you expect to find test exit criteria described9

Question 6

(0)

The following 4 equivalence classes are given: Which of the following alternatives includes correct test values for x. based on equivalence partitioning?

Question 7

(0)

Which of the following coverage criteria results in the highest coverage for state transition based test cases?

Question 8

(0)

Which of the following statements about testware are correct? I When closing the test activities, all the testware resources can be uninstalled and released II All the testware should be subject t

Question 9

(0)

A QA manager of a start-up company needs to implement within a week a low cost incident management tool. Which of the following is the best option?

Question 10

(0)

Which of the following statements regarding inspection is NOT true?

Related questions

Which of the following can be considered a VALID exit criterion? I Estimates of defect density or reliability measures. II . The completion and publication of an exhaustive Test Report. III . Accuracy measures, such as code, functionality or risk coverage. IV Residual risks such as lack of code coverage in certain areas.

The following diagram displays the logical dependencies between requirements and the individual requirement priorities. For example, 'R2->R3' means that R3 is dependent on R2. Priority is indicated by the number next to the letter ''P' i.e. P1 has a higher priority than P2. Which one of the following options best describes the test execution sequence using both requirement dependency and priority

Which of the following BEST matches the descriptions with the different categories of test techniques? 1. Test cases are based on the test basis which may include the requirements, use cases and user stories 2. Test cases are based on the test basis which may include the software architecture or code 3. Test cases can show deviations from the requirements 4. These test techniques are applicable to both functional and non-functional testing 5. Tests are based on knowledge of developers, users and other stakeholders Black - Black-box test techniques White * White-box test techniques Experience - Experience-based test techniques

A financial institution is to implement a system that calculates the interest rates paid on investment accounts based on the sum invested. You are responsible for testing the system and decide to use equivalence partitioning and boundary value analysis to design test cases. The requirements describe the following expectations: Investment range | Interest rate R500 to RIO 000 10% RIO 001 to R50 000 11% R50 001 to RlOOOOO 12% RIOOOOl to R500 000 | 13% What is the minimum number of test cases required to cover all valid equivalence partitions for calculating the interest?

Which of the following about typical information found within a test plan is FALSE?

Consider the following simplified version of a state transition diagram that specifies the behavior of a video poker game: What Is the minimum number of test cases needed to cover every unique sequence of up to 3 states/2 transitions starting In the 'Start' state and ending In the 'End' state?

For the same financial institution in Question 12, with the same requirements and expectations, what would be the most likely investment values used in testing if two-point boundary value analysis is used to design test cases specific to the 13% interest rate equivalence partition?

The following decision table is used to assist a doctor in determining the drug therapy to prescribe for a patient (aged 6 to 65 years) diagnosed with acute sinusitis. The table consists of three Boolean conditions and six actions Based only on the given information, which of the following statements is TRUE?

Which of the following is a factor that contributes to a successful review?

Consider a review for a high-level architectural document written by a software architect. The architect does most of the review preparation work, including distributing the document to reviewers before the review meeting. However, reviewers are not required to analyze the document in advance, and during the review meeting the software architect explains the document step by step. The only goal of this review is to establish a common understanding of the software architecture that will be used in a software development project. Which of the following review types does this review refer to?

Question 8 - CTFL4 discussion

Which of the following statements about testware are correct?

I When closing the test activities, all the testware resources can be uninstalled and released

II All the testware should be subject to Configuration Management

III . The testware. at the end of the project, should be transferred to the organization responsible for maintenance

IV The developers are responsible for the correct installation of the testware

II, Ill

I, Ill

I, IV

II, IV

Suggested answer: A

Explanation:

Testware is a term that refers to all artifacts produced during the testing process, such as test plans, test cases, test scripts, test data, test results, defect reports, etc. The following statements about testware are correct:

II) All the testware should be subject to Configuration Management. Configuration management is a process that establishes and maintains consistency among work products throughout their life cycle. Configuration management applies to all testware, as it helps ensure their quality and consistency, track their changes and defects, control their versions and access rights, and link them to other artifacts.

III) The testware at the end of the project should be transferred to the organization responsible for maintenance. Maintenance testing is testing performed on a software product after delivery to correct defects or improve performance or other attributes. Maintenance testing requires testware from previous testing activities or phases, such as test cases, test data, test results, etc. Therefore, the testware at the end of the project should be transferred to the organization responsible for maintenance testing, such as support team or maintenance team. The following statements about testware are incorrect:

I) When closing the test activities, all the testware resources can be uninstalled and released. This statement is incorrect, as some testware resources may still be needed for future testing activities or phases, such as maintenance testing or regression testing. Therefore, when closing the test activities, some testware resources should be archived and stored for future use, while others can be uninstalled and released.

IV) The developers are responsible for the correct installation of the testware. This statement is incorrect, as the testers are responsible for the correct installation of the testware. The testers should ensure that they have access to all necessary testware resources and that they are installed and configured properly before starting the test execution. Verified

Reference:A Study Guide to the ISTQB Foundation Level 2018 Syllabus - Springer, Chapter 6, page 58-61.

Show Answer

asked 18/09/2024

Mario Peralta

36 questions

Your answer: A B C D

0 comments

Sorted by