Home

Home / ISTQB / CTFL4

Question list

List of questions

Question 1

(0)

Which of the following statements about re-testing and regression testing are TRUE? I Re-testing should be performed after a defect is fixed. II Regression testing should always be performed after

Question 2

(0)

Which of the following can be considered a VALID exit criterion? I Estimates of defect density or reliability measures. II . The completion and publication of an exhaustive Test Report. III . Acc

Question 3

(0)

Which of the following s the most correct statement about state testing techniques?

Question 4

(0)

A test manager decided to skip static testing since he believes bugs can be found easily by doing dynamic testing. Was this decision right or wrong?

Question 5

(0)

In which of the following test documents would you expect to find test exit criteria described9

Question 6

(0)

The following 4 equivalence classes are given: Which of the following alternatives includes correct test values for x. based on equivalence partitioning?

Question 7

(0)

Which of the following coverage criteria results in the highest coverage for state transition based test cases?

Question 8

(0)

Which of the following statements about testware are correct? I When closing the test activities, all the testware resources can be uninstalled and released II All the testware should be subject t

Question 9

(0)

A QA manager of a start-up company needs to implement within a week a low cost incident management tool. Which of the following is the best option?

Question 10

(0)

Which of the following statements regarding inspection is NOT true?

Open VPLUS File

Convert VPLUS to PDF

Related questions

Which of the following can be considered a VALID exit criterion? I Estimates of defect density or reliability measures. II . The completion and publication of an exhaustive Test Report. III . Accuracy measures, such as code, functionality or risk coverage. IV Residual risks such as lack of code coverage in certain areas.

The following diagram displays the logical dependencies between requirements and the individual requirement priorities. For example, 'R2->R3' means that R3 is dependent on R2. Priority is indicated by the number next to the letter ''P' i.e. P1 has a higher priority than P2. Which one of the following options best describes the test execution sequence using both requirement dependency and priority

Which of the following BEST matches the descriptions with the different categories of test techniques? 1. Test cases are based on the test basis which may include the requirements, use cases and user stories 2. Test cases are based on the test basis which may include the software architecture or code 3. Test cases can show deviations from the requirements 4. These test techniques are applicable to both functional and non-functional testing 5. Tests are based on knowledge of developers, users and other stakeholders Black - Black-box test techniques White * White-box test techniques Experience - Experience-based test techniques

A financial institution is to implement a system that calculates the interest rates paid on investment accounts based on the sum invested. You are responsible for testing the system and decide to use equivalence partitioning and boundary value analysis to design test cases. The requirements describe the following expectations: Investment range | Interest rate R500 to RIO 000 10% RIO 001 to R50 000 11% R50 001 to RlOOOOO 12% RIOOOOl to R500 000 | 13% What is the minimum number of test cases required to cover all valid equivalence partitions for calculating the interest?

Which of the following about typical information found within a test plan is FALSE?

Consider the following simplified version of a state transition diagram that specifies the behavior of a video poker game: What Is the minimum number of test cases needed to cover every unique sequence of up to 3 states/2 transitions starting In the 'Start' state and ending In the 'End' state?

For the same financial institution in Question 12, with the same requirements and expectations, what would be the most likely investment values used in testing if two-point boundary value analysis is used to design test cases specific to the 13% interest rate equivalence partition?

The following decision table is used to assist a doctor in determining the drug therapy to prescribe for a patient (aged 6 to 65 years) diagnosed with acute sinusitis. The table consists of three Boolean conditions and six actions Based only on the given information, which of the following statements is TRUE?

Which of the following is a factor that contributes to a successful review?

Consider a review for a high-level architectural document written by a software architect. The architect does most of the review preparation work, including distributing the document to reviewers before the review meeting. However, reviewers are not required to analyze the document in advance, and during the review meeting the software architect explains the document step by step. The only goal of this review is to establish a common understanding of the software architecture that will be used in a software development project. Which of the following review types does this review refer to?

Question 10 - CTFL4 discussion

Report

Which of the following statements regarding inspection is NOT true?

A.

An inspection may be led by a trained moderator who shall not be the author.

B.

The main purpose of an inspection is to find solutions to the problems.

C.

An inspection can be performed by peers.

D.

An inspection shall follow a formal process based on rules and checklists with entry and exit criteria

Suggested answer: B

Explanation:

An inspection is a type of review that follows a defined process with formal entry and exit criteria and roles and responsibilities for participants. An inspection can be performed by peers with different roles, such as moderator, author, reviewer and scribe. The following statement about inspection is not true:

B) The main purpose of an inspection is to find solutions to the problems. This statement is not true, as the main purpose of an inspection is to find defects or issues in a work product, not to find solutions to the problems. Finding solutions to the problems is a debugging or problem-solving activity that is usually performed by the author or developer after receiving the inspection report. The following statements about inspection are true:

A) An inspection may be led by a trained moderator who shall not be the author. This statement is true, as an inspection requires a moderator role who leads the inspection process and ensures that it follows the rules and standards. The moderator should be trained in inspection techniques and should not be the author of the work product under inspection, in order to avoid bias or conflict of interest.

C) An inspection can be performed by peers. This statement is true, as an inspection involves peer review, which means that the work product under inspection is evaluated by people who have similar roles or expertise as the author, but who are not directly involved in creating or modifying the work product.

D) An inspection shall follow a formal process based on rules and checklists with entry and exit criteria. This statement is true, as an inspection follows a formal process that consists of six main steps: planning, kick-off meeting, individual preparation, review meeting, rework and follow-up. Each step has defined rules and checklists to guide the participants and ensure consistency and quality. Each step also has entry and exit criteria to ensure that the prerequisites and objectives are met before moving to the next step. Verified

Reference:A Study Guide to the ISTQB Foundation Level 2018 Syllabus - Springer, Chapter 3, page 28-29.

Show Answer

asked 18/09/2024

Srinivasan Krishnamoorthy

39 questions

User

Your answer: A B C D

0 comments

Sorted by

Leave a comment first