You want to use vMotion to move the entire state of a running virtual machine between hosts over a dedicated vMotion network without service interruption.What are two vMotion prerequisites before performing this task? (Choose two.)

Verify that you have at least two ESXi hosts that are licensed for vMotion or are in evaluation mode

Verify that hosts have access to shared storage of a supported type, such as Fibre Channel, iSCSI, or NAS

Verify that you have at least two ESXi hosts that are licensed for vMotion or are in evaluation mode

Verify that you have running instances of vCenter Server and the ESXi hosts are in maintenance mode.

Verify that hosts have access to shared storage of a supported type, such as Fibre Channel, iSCSI, or NAS

Verify that the source and destination hosts have specific Intel x86 CPUs.

What are two expected results of the VMware vMotion test plan conducted by VCE at the completion of a Vblock System build? (Choose two.)

No unexpected errors or faults occur.

There will be minimal packet loss during vMotion.

No unexpected errors or faults occur.

The secondary VSM takes over from the primary VSM.

There will be minimal packet loss during vMotion.

Traffic fails over to the redundant port channel each time a port-channel is disabled.

What is a valid method to install EMC PowerPath/VE onto a VMware ESXi host?

Install using vCenter Update Manager (VUM).

Install from the PowerPath/VE vCenter plug-in.

Install remotely from the array management server.

Install using the rpowermt command.

What is a reason to use EMC Powerpath/VE on a Vblock System 720?

to optimize load balancing on the storage fabric

to provision storage from the vCenter client

to optimize load balancing on the storage fabric

to add additional vStorage APIs for Array Integration (VAAI) features

to optimize storage caching features on the ESXi host

What are three possible results when enabling vSphere High Availability (HA)? (Choose three.)

An ESXi host fails and some of the virtual machines restart on other hosts in the cluster.

A virtual machine fails and automatically restarts on another host in the cluster.

A virtual machine is unable to boot due to limited cluster resources.

Virtual machines will migrate from one host to another as resource availability changes.

An ESXi host fails and some of the virtual machines restart on other hosts in the cluster.

A virtual machine fails and automatically restarts on another host in the cluster.

VMware vSphere Fault Tolerance will be enabled.

A virtual machine is unable to boot due to limited cluster resources.

Using PowerPath/VE, which two details are expected outputs from the rpowermt display dev=all command? (Choose two.)

serial number for the connected storage array

A host is a member of a high availability (HA) cluster in vCenter. There is a failure of a B-series blade in a Vblock System 720.What are three ways that vCenter is impacted? (Choose three.)

vCenter will recognize the host's absence and high availability will restart the virtual machines on the remaining hosts depending on resource constraints.

vCenter will use Distributed Resource Scheduling (DRS) to vMotion virtual machines based on the reduced resources available.

The amount of resources available to the cluster will be reduced until the outage is restored.

vCenter will recognize the host's absence and high availability will restart the virtual machines on the remaining hosts depending on resource constraints.

The vCenter virtual machine will restart on another available host, there will be no impact to production data on the Vblock.

vCenter will use Distributed Resource Scheduling (DRS) to vMotion virtual machines based on the reduced resources available.

The outage will require remediation to restore vCenter functionality.

The amount of resources available to the cluster will be reduced until the outage is restored.

What are three purposes of the master host in a vSphere high availability (HA) cluster? (Choose three.)

to monitor the state of slave hosts

to monitor the power state of all protected virtual machines

to manage the lists of cluster hosts

to monitor the state of slave hosts

to monitor the power state of all protected virtual machines

to manage the lists of cluster hosts

to migrate virtual machines when a vMotion is requested

to install the HA agent on newly added hosts

You observe that a host in a high availability (HA) cluster shows as disconnected within vCenter. The virtual machines running on the disconnected host have not automatically restarted as expected.What is the cause of this problem?

The host is still exchanging a data store heartbeat.

NTP was not configured on the HA cluster.

vMotion is not enabled on the cluster hosts.

The disconnected host was the master host.

The host is still exchanging a data store heartbeat.

A host has been placed into maintenance mode in a Distributed Resource Scheduler (DRS) enabled cluster for patching. The virtual machines have not migrated as expected. DRS settings have been verified as fully automated at the cluster level.What would cause this condition?

vMotion is not enabled on the vMotion vmkernel interface for the selected host.

The selected host is using a different ESXi version than the rest of the cluster.

vMotion is not enabled on the vMotion vmkernel interface for the selected host.

The high availability agent has not been properly installed on the selected host.

DNS is not enabled at the host level for the selected host.

Which two statements are correct regarding VCE implementation of a persistent scratch partition? (Choose two.)

You must configure a persistent scratch partition on the boot-from-SAN VMFS data store.

VCE uses the persistent scratch partition to ensure that critical log files are available.

You must configure a persistent scratch partition on the boot-from-SAN VMFS data store.

You must configure a persistent scratch partition on the boot-from-SAN NFS data store.

Vblock Systems use centralized monitoring with syslog and SNMP in place of a persistent scratch location.

VCE uses the persistent scratch partition to ensure that critical log files are available.

In the Vblock System 720, what describes the VCE standard method of zoning?

single initiator to single target

multi initiator to single target

single initiator to multi target

single initiator to single target

multi initiator to multi target

a collection of Fibre Channel addresses in a zone

What information is displayed when an administrator uses the show vsan membership command on a Cisco MDS switch?

membership information for all VSANs

information for a specific VSAN

membership information for all VSANs

membership information for a specified VSAN

zone database information for a specific VSAN

On a Vblock System 320, each VMware ESXi host will boot from a SAN-attached boot drive presented from the EMC VNX array.Which statement is true according to VCE standards for boot LUNs?

Use SAS drives to create a RAID group, use RAID-5 4+1 RAID group, then create a 20 GB LUN.

Use Fibre Channel drives to create a RAID group, use RAID-5 4+1 RAID group, then create a 20 GB LUN.

Use Fibre Channel drives to create a RAID group, use RAID-5 7+1 RAID group, then create a 20 GB LUN.

Use SAS drives to create a RAID group, use RAID-5 4+1 RAID group, then create a 20 MB LUN.

Use SAS drives to create a RAID group, use RAID-5 4+1 RAID group, then create a 20 GB LUN.

What is the hot spare drive requirement for a Vblock System 320 storage array?

Hot spare drives must exist for every 30 drives of the same type drive in the array.

Hot spare drives must exist for every 100 drives of any type drive in the array.

Hot spare drives must exist for every 100 drives of the same type drive in the array.

Hot spare drives must exist for every 30 drives of the same type drive in the array.

Hot spare drives must exist for every 30 drives of any type drive in the array.

A SAN administrator must use the zone commit command to activate a zone set on a Cisco MDS 9148.Which feature is enabled on the switch?

hardware zoning by access control lists

During a Vblock System 320 deployment, the implementation engineer needs to access UCS Manager to verify the compute configuration.Which two IP addresses are used to open the GUI? (Choose two.)

the secondary switch IP address

VCE 210-010 Practice Test 2 - Free Online Exam Prep & Questions

Which three configuration parameters are available to create a virtual machine when performing a typical installation? (Choose three.)

Become a Premium Member for full access

Unlock Premium Member

VCE 210-010 Practice Test 2

Question

VCE 210-010 Practice Tests

Practice Tests