During a Vblock System logical build, which three configuration changes require Unified Computing System Manager (UCSM) access? (Choose three.)

ESXi host Network Time Protocol

A Vblock System 720 has been configured in the factory according to the VCE Logical Build Guide.Which statement is correct?

Each service-profile should have at least one vNIC pinned to fabric interconnect A; one vNIC pinned to fabric interconnect B, and failover disabled.

Each service-profile should have at least one vNIC pinned to fabric interconnect A; one vNIC pinned to fabric interconnect B, and failover enabled.

Each service-profile should have at least one vNIC pinned to fabric interconnect A; one vNIC pinned to fabric interconnect B, and failover disabled.

Each service-profile should have at least one vHBA pinned to fabric interconnect A; one vHBA pinned to fabric interconnect B, and failover enabled.

Each service-profile should have at least one vHBA pinned to fabric interconnect A; one vHBA pinned to fabric interconnect B, and failover disabled.

An engineer is deploying a Vblock System without using EMC's Unified Infrastructure Manager (UIM).Which three pools are required to be configured in Unified Computing System Manager (UCSM)? (Choose three.)

Media Access Control (MAC) address

Cisco Integrated Management Controlled (CIMC)

A customer uses EMC's Unified Infrastructure Manager (UIM) to deploy a Vblock System.Which two post-deployment steps must the engineer take within Unified Computing System Manager (UCSM) to provide a VCE best-practice configuration? (Choose two.)

Set the Fibre Channel QoS policy in service profiles.

Set the host firmware package in service profiles.

Set the Fibre Channel QoS policy in service profiles.

Set the host firmware package in service profiles.

Associate the service profiles to blades

Set enable failover for vNICs in service profiles.

A Cisco Unified Computing System (UCS) blade encounters a hardware failure that requires the service profile to be associated to another blade.Once the service profile is associated to another blade, how does the host boot the existing operating system?

The service profile maintains the boot-policy to ensure the replacement blade boots to the existing LUN on the storage array.

The service profile maintains pointers to the local hard drives on the failed blade allowing true stateless migration.

The service profile maintains the boot-policy to ensure the replacement blade boots to the existing LUN on the storage array.

The service profile migrates the hard drive content from the failed blade to the new blade during service profile re-assignment.

The service profile migration requires that the drives from the failed blade are physically migrated to the replacement blade to boot the existing operating system.

Which component connects a Vblock System 720 to a customer's network aggregation layer?

Cisco UCS Fabric Interconnect 6296UP

What is the requirement for adding VLANs to port channels for disjointed Layer 2 networks in a Cisco UCS?

VLANs must be explicitly assigned to an uplink.

VLANs should not be explicitly assigned to an uplink.

VLAN traffic must be allowed to travel over all uplinks.

VLANs must be assigned in the 301-400 range.

Which Cisco Nexus 5000 Series switch feature provides traffic prioritization and egress bandwidth allocation for a Vblock System 320 deployment?

jumbo maximum transmission units (MTU)

In a Vblock System 320, which type of port channel is configured from the Cisco Nexus 5548 switch to the fabric interconnects?

virtual port channel plus (vPC+)

An administrator is unable to connect the Cisco Nexus 1000V to the vCenter server. The following error is displayed:{ERROR: [VMWARE-VIM] Extension key was not registered before its use.}Which action would resolve this error?

From VMware vCenter, register the Cisco Nexus 1000V xml plug-in.

From the Cisco Nexus 1000V, use the connect command.

From the Cisco Nexus 1000V, use the vmware vc extension-key command.

From VMware vCenter, create a new vSphere Distributed Switch.

From VMware vCenter, register the Cisco Nexus 1000V xml plug-in.

You are adding a new VLAN from the Cisco Nexus 1000V. You use the state enabled command.What is the result of this command?

It creates a port group in the vCenter server.

It creates a new VLAN in the Cisco Nexus 1000V.

It creates a new VMkernel port in the ESXi host.

It creates a new VLAN in the Cisco fabric interconnects.

It creates a port group in the vCenter server.

-- Exhibit -- -- Exhibit --Click the Exhibit button.Vblock Systems have multiple power connector capabilities.Which power receptacle is shown in the exhibit?

30A 250V, 3 phase (NEMA L15-30P)

30A 120V, 3 phase (C8303 L6-30P)

-- Exhibit -- -- Exhibit --Click the Exhibit button.Vblock Systems have multiple power connector capabilities.Which power receptacle is shown in the exhibit?

60A 250V, single phase (IEC 60309)

30A 120V, 3 phase (C8303 L6-30P)

When powering on a Vblock System what is the correct power up sequence?

Switches, AMP, SAN, UCS chassis, and UCS blades

Switches, SAN, UCS chassis, UCS blades, and AMP

Switches, AMP, UCS chassis, UCS blades, and SAN

Switches, SAN, AMP, UCS chassis, and UCS blades

After the installing the Cisco Nexus 1000V, the administrator uses the command show svs connections.This command shows the connection status of which component?

Secondary Virtual Supervisor Module

A customer would like to add a new production VLAN to their Vblock System with UIM/P. The VLAN was added to the UIM/P service profile, and the connected Cisco Nexus 5000. The customer is still not able to use the new VLAN with a virtual machine.Which step must the customer complete?

Add the VLAN to Cisco Nexus 1000V.

Add the VLAN to Cisco Catalyst 3560.

Which tool in the Advanced Management Pod (AMP) would a customer use to determine if their Vblock System is compliant with a specific Release Certification Matrix (RCM)?

VCE Vision Intelligent Operations

VMware vCenter Server Inventory Service

A customer wants to ensure that the new installed Vblock System 320 storage array is being monitored by EMC.Which EMC monitoring tool must be installed to accomplish this?

EMC Secure Remote Support (ESRS)

Data Center Network Manager (DCNM)

EMC Secure Remote Support (ESRS)

Which two steps are required to complete a Cisco UCS Smart Call Home registration on a Vblock System? (Choose two.)

After receiving the e-mail response from Cisco, click the link in the e-mail to complete registration for Smart Call Home.

Select "Send System Inventory Now" in UCSM.

After receiving the e-mail response from Cisco, click the link in the e-mail to complete registration for Smart Call Home.

Select "Send System Inventory Now" in UCSM.

Configure UCSM to send periodic system inventory messages.

Configure the SNMP trap destination.

-- Exhibit -- -- Exhibit --Click the Exhibit button.Referring to the exhibit, which Vblock System 320 component is "A"?

Cisco Chassis containing blade servers

VCE 210-010 Practice Test 3 - Free Online Exam Questions 81-120

During a Vblock System 320 deployment, the customer wants to disassociate four half-width blades in a single chassis for a future project.

Which tool is used to perform this compute reconfiguration?

Become a Premium Member for full access

Unlock Premium Member

VCE 210-010 Practice Test 3

Question

Drag and Drop

Hot Area

VCE 210-010 Practice Tests

Practice Tests