You have identified a blade that has faulty hardware and must be replaced. You have an unused blade that is not associated with any service profile.What are two ways to provision the unused blade with the same policies? (Choose two.)

Clone the service profile and apply it to the unused blade.

Change the service profile association.

Clone the service profile and apply it to the unused blade.

Create a new service profile template from the faulty blade.

Change the service profile association.

Change the UUID of faulty blade to that of the unused blade.

Click the Exhibit button. Referring to the exhibit, what should you select to remove a service profile?

Change Service Profile Association

You are performing the logical build on a Vblock System 340 with 32 blades and UIM/P is not going to be used. You need to deploy multiple service profiles at one time.In the UCSM GUI, what would you select?

Create Service Profiles from Template

Create Service Profile (expert)

Create Service Profiles from Template

Create Service Profile from Template

You must create several service profiles that will all have the same policies and will also be updated in the future.Which action would allow you to update multiple service profiles after they have been associated?

Create a service profile template with type set to updating template.

Create a service profile clone of each service profile.

Create a service profile template with type set to initial template.

Create a service profile template with type set to updating template.

Create an update policy for each service profile.

You are adding a new blade to a UCS chassis. You want the new blade to obtain all of your policies that are currently applied to another service profile.Which three actions will accomplish this task? (Choose three.)

Clone the service profile from an existing service profile.

Create the service profile from a template.

Create a new service profile using the same policies.

Clone the service profile from an existing service profile.

Create the service profile from a template.

Reassign the service profile to a new server.

Copy the service profile between blades.

Create a new service profile using the same policies.

To associate a blade with a service profile, what information is required? (Choose two.)

a management IP address for the ESXi host

You want to associate a service profile in UCS.Which action would you perform?

Select Change Service Profile Association on the service profile.

Select the ESXi server that you want to associate.

Select the service offering that you want to associate.

Select the chassis that you want to associate.

Select Change Service Profile Association on the service profile.

In the UCS system, what is the purpose of the Chassis Discovery Policy?

It defines the minimum number of links necessary before a chassis can be discovered.

It defines the minimum number of links to be used in the data plane.

It defines the maximum number of links to be used in the data plane.

It defines the minimum number of links necessary before a chassis can be discovered.

It defines the maximum number of links necessary before a chassis can be discovered.

After activating the host firmware package during a UCS code upgrade, all of the blades in the Vblock System 340 begin a reboot process.Which policy is required to prevent this from occurring?

maintenance policy set to "user acknowledge"

power control policy set to "cap"

maintenance policy set to "user acknowledge"

boot policy set to "Boot Mode=UEFI"

BIOS policy set to "Quiet Boot=enabled"

You want to create a BIOS policy in accordance with VCE best practices.What would you do to accomplish this task?

You create a BIOS policy when using UIM/P or UCSM.

You create a BIOS policy only when using UIM/P.

You create a BIOS policy only when using UCSM.

You create a BIOS policy when using UIM/P or UCSM.

You do not create a BIOS policy when using UIM/P or UCSM.

Which three settings does a boot policy determine? (Choose three.)

the configuration of the boot device

the location from which the server boots

the order in which boot devices are invoked

the configuration of the boot device

the operating system to be installed

the location from which the server boots

the order in which boot devices are invoked

the service profile to be associated

Click the Exhibit button. Referring to the exhibit, what are two results of the cluster lead b command? (Choose two.)

The UCS will assign a cluster IP address to FI-B.

The UCS FI-B will become the cluster leader.

The UCS FI-A will reboot and FI-B will become the cluster leader.

The UCS will assign a cluster IP address to FI-B.

The UCS FI-B will become the cluster leader.

The UCS will swap assigned IP addresses between FI-A and FI-B.

Click the Exhibit button. The startup version has been updated to version 2.13.c.What is the result of activating the I/O modules shown in the exhibit?

The UCS will apply staged code on both I/O modules, the modules will reboot.

The UCS will stage the new code to one I/O module, the module will not reboot.

The UCS will stage the new code to both I/O modules, the modules will not reboot.

The UCS will apply staged code on one I/O module, the module will reboot.

The UCS will apply staged code on both I/O modules, the modules will reboot.

A production UCS environment is receiving hardware upgrades. You perform a software upgrade from version 2.0 to version 2.1.1e. After completing the upgrade tasks successfully, the systems starts reporting several alerts shown below:Fault Code:F0502 Message DIMM invalid FRU DIMMFault Code:F0801 Message Processor invalid FRU Processor Fault Code:F0200 Message Adapter unidentified FRU AdapterWhich action will resolve the alerts?

Reinstall the Infrastructure Software Bundle package.

Reboot both fabric interconnects, one at a time.

Change the log settings level to report errors only.

Click the Exhibit button. You are connected to a Cisco fabric interconnect and have been asked to verify the high availability status.Referring to the exhibit, what will the cluster lead a command do?

It sets the subordinate fabric interconnect to be the primary.

It changes the fabric interconnect to operate in standalone mode.

It sets the Cisco Stackwise Cluster lead to the A switch.

It sets the subordinate fabric interconnect to be the primary.

It will fail, since the switch is already the primary.

Click the Exhibit button. Referring to the exhibit, according to the VCE Logical Build Guide, in which location do you create customer VLANs to support data traffic?

LAN > LAN Cloud > Fabric A > VLANs

Click the Exhibit button. Your client explains that they are not able to communicate with virtual machines in the UCS using a packet size of 9000.Referring to the exhibit, what needs to be corrected to resolve the network problem?

QoS system Class > priority Best Effort > MTU > 9216

QoS system Class > priority Platinum > MTU > 9216

QoS system Class > priority Gold > MTU > 9216

QoS system Class > priority Silver > MTU > 9216

QoS system Class > priority Best Effort > MTU > 9216

Which L1/L2 connectivity condition must be met for UCS fabric interconnects to work in a cluster?

The L1 and L2 ports are direct connected between fabric interconnects.

The L1 and L2 ports on both fabric interconnects are locally switched.

The L1 and L2 ports on both fabric interconnects are routed.

The L1 and L2 ports are direct connected between fabric interconnects.

The L1 and L2 ports are cross connected between fabric interconnects.

What are two purposes of the L1/L2 ports on a fabric interconnect? (Choose two.)

They carry cluster heartbeat messages between two fabric interconnects.

They carry high-level management messages between the two devices.

They carry the Fibre Channel traffic for SAN only.

They carry cluster heartbeat messages between two fabric interconnects.

They carry high-level management messages between the two devices.

They carry data plane traffic in the event of a fabric interconnect failure.

During a Vblock System 340 deployment, you are asked to configure an ESXi server for testing. You install the server OS and setup the network configuration. You then create separate VLANs and port channels to the core switches. You are unable to ping the ESXi host on the blade. The network adapter shows a status of connected from the ESXi host on the correct vNIC.Which two statements describe the reason for the problem? (Choose two.)

The UCS vNIC is not configured with the corresponding VLAN.

The ESXi host has a specified VLAN ID and VLAN tagging is not in use.

The UCS vNIC is not configured with the corresponding VLAN.

The disjointed Layer 2 network topology is not properly configured.

The ESXi host has a specified VLAN ID and VLAN tagging is not in use.

The ESXi host has no VLAN ID and VLAN tagging is not in use.

You are asked to create additional VLANs in the UCS Manager.According to VCE, which setting would be chosen to complete this task?

Both Fabrics Configured Differently

Which two port types would be configured in the UCS fabric interconnect? (Choose two.)

Fibre Channel uplink ports between the fabric interconnect and the uplink Fibre Channel switch

Ethernet uplink ports between the fabric interconnect and the up-link Ethernet switch

Fibre Channel uplink ports between the fabric interconnect and the uplink Fibre Channel switch

Fibre Channel server ports between the I/OM and the back-end server ports

Ethernet uplink ports between the fabric interconnect and the up-link Ethernet switch

server ports between the fabric interconnect and the storage

VCE 210-020 Practice Test 1 - Free Online Exam Questions 1-40

Which UCS feature allows you to quickly create several service profiles with the same basic parameters?

Pools

Policies

Initial profile

Templates

Comment (0)

VCE 210-020 Practice Test 1

Question

Drag and Drop

Hot Area

VCE 210-020 Practice Tests

Practice Tests