Home / Cisco / 300-420

Cisco 300-420 Practice Test - Questions Answers, Page 17

Question list

List of questions

Question 161

(0)

DRAG DROP Drag and drop the components in a Cisco SD-Access architecture from the left onto their descriptions on the right.

Question 162

(0)

DRAG DROP Drag and drop the elements from the left onto the functions they perform in the Cisco SD-WAN architecture on the right.

Question 163

(0)

DRAG DROP Drag and drop the descriptions from the left onto the corresponding WAN connectivity types and categories on the right.

Question 164

(0)

DRAG DROP Drag and drop the descriptions from the left onto the corresponding VPN types on the right.

Question 165

(0)

DRAG DROP Drag and drop the characteristics from the left onto the configuration protocols they describe on the right.

Question 166

(0)

DRAG DROP Drag and drop the elements from the left onto the YANG models where they and used on the right.

Question 167

(0)

Refer to the exhibit. A network engineer is designing an OSPF solution to connect a company's remote to a newly provisioned MPLS VPN backbone. Some of the branches have a direct dark fiber co

Question 168

(0)

An engineer uses Postman and YANG to configure a router with: OSPF process ID 200 network 172.16.10.128/26 enabled for Area 0 Which get-config reply verifies that the model set was designed correct

Question 169

(0)

An engineer must use YANG with an XML representation to configure a Cisco IOS XE switch with these specifications: IP address 10.10.10.10/27 configured on the interface GigabitEthernet2/1/0 connect

Question 170

(0)

An engineer uses Postman and YANG to configure a router with: OSPF process ID 400 network 192.168.128.128/25 enabled for Area 0 Which get-config reply verifies that the model set was designed

Related questions

Which queuing structure is used on SD-WAN Edge routers?

DRAG DROP Drag and drop the characteristics from the left onto the correct telemetry mode on the right.

Which consideration must be taken into account when using the DHCP relay feature in a Cisco SDAccess Architecture?

Which WAN connectivity technology is optimal for edge computing compared to others and why?

Which feature is used to optimize WAN bandwidth of IGMP network traffic among WAN Edge routers in the same VPN?

Refer to the exhibit. An engineer must design a WAN solution so that ISP-1 is always preferred over ISP-2. The path via ISP-2 is considered as a backup and must be used only when the path to ISP-1 is down. Which solution must the engineer choose? A. R1: - Routes advertised to ISP-1: 0x AS-path prepend - Routes received from ISP-1: HIGH local-preference - Routes advertised to R2: no action - Routes received from R2: community NO-EXPORT R2: - Routes advertised to ISP-2:5x AS-path prepend - Routes received from ISP-2: LOW local-preference - Routes advertised to R1: community NO-ADVERTISE - Routes received from R1: no action

An engineer must design an in-band management solution for a customer with branch sites. The solution must allow remote management of the branch sites using management protocols over an MPLS WAN. Queueing is implemented at the remote sites using these classes: How must the solution prioritize the management traffic over the WAN?

An architect must create a QoS solution for a customer to ensure that a 40 Mbps Internet connection is shared between four subnets based on these requirements: * Each subnet must receive no less than 10 Mbps of download bandwidth during peak traffic times. * A subnet can use up to 40 Mbps during nonpeak traffic times if the other subnets are idle. * Download traffic must never experience a delay. Which solution must the architect choose?

An engineer must design a QoS solution for a customer. The network currently supports data only, but the customer will roll out VoIP and IP video in conjunction with the new QoS solution. The engineer plans to use DiffServ. To ensure priority for voice services, which model must the design include?

Which two functions does the control plane node provide in a Cisco SD-Access architecture? (Choose two.)

Question 161

DRAG DROP

Drag and drop the components in a Cisco SD-Access architecture from the left onto their descriptions on the right.

Show Answer Comment (0)

Question 162

DRAG DROP

Drag and drop the elements from the left onto the functions they perform in the Cisco SD-WAN architecture on the right.

Show Answer Comment (0)

Question 163

DRAG DROP

Drag and drop the descriptions from the left onto the corresponding WAN connectivity types and categories on the right.

Show Answer Comment (0)

Question 164

DRAG DROP

Drag and drop the descriptions from the left onto the corresponding VPN types on the right.

Show Answer Comment (0)

Question 165

DRAG DROP

Drag and drop the characteristics from the left onto the configuration protocols they describe on the right.

Show Answer Comment (0)

Question 166

DRAG DROP

Drag and drop the elements from the left onto the YANG models where they and used on the right.

Show Answer Comment (0)

A network engineer is designing an OSPF solution to connect a company's remote to a newly provisioned MPLS VPN backbone. Some of the branches have a direct dark fiber connection between each other. The engineer wants to ensure that the dark fibers are used only when the MPLS core is unavailable. Which solution must the engineer choose?

Stub area

Sham link

Virtual link

NSSA

Show Answer Comment (0)

Question 168

An engineer uses Postman and YANG to configure a router with:

OSPF process ID 200 network 172.16.10.128/26 enabled for Area 0 Which get-config reply verifies that the model set was designed correctly?

Show Answer Comment (0)

Question 169

An engineer must use YANG with an XML representation to configure a Cisco IOS XE switch with these specifications:

IP address 10.10.10.10/27 configured on the interface GigabitEthernet2/1/0 connectivity from a directly connected host 10.10.10.1/27 Which YANG data model set must the engineer choose?