ExamGecko
Home / Cisco / 300-420 / List of questions
Ask Question

Cisco 300-420 Practice Test - Questions Answers, Page 4

List of questions

Question 31

Report Export Collapse

When vEdge router redundancy is designed, which FHRP is supported?

HSRP

HSRP

OMP

OMP

GLBP

GLBP

VRRP

VRRP

Suggested answer: D
asked 07/10/2024
Daniel Calleja
38 questions

Question 32

Report Export Collapse

Which feature is required for graceful restart to recover from a processor failure?

Cisco Express Forwarding

Cisco Express Forwarding

Virtual Switch System

Virtual Switch System

Stateful Switchover

Stateful Switchover

Bidirectional Forwarding Detection

Bidirectional Forwarding Detection

Suggested answer: C
Explanation:

https://archive.nanog.org/meetings/nanog42/presentations/Weissner_SSO.pdf

The Stateful Switchover (SSO) feature works with Nonstop Forwarding (NSF) in Cisco software to minimize the amount of time a network is unavailable to its users following a switchover. The primary objective of SSO is to improve the availability of networks constructed with Cisco routers.

asked 07/10/2024
Cheah Eng Soon
38 questions

Question 33

Report Export Collapse

Which method will filter routes between EIGRP neighbors within the same autonomous system?

distribute-list

distribute-list

policy-based routing

policy-based routing

leak-map

leak-map

route tagging

route tagging

Suggested answer: A
asked 07/10/2024
vladimir tolkunov
36 questions

Question 34

Report Export Collapse

An infrastructure team is concerned about the shared memory utilization of a device, and for this reason, they need to monitor the device state. Which solution limits impact on the device and provides the required data?

IPFIX

IPFIX

static telemetry

static telemetry

on-change subscription

on-change subscription

periodic subscription

periodic subscription

Suggested answer: C
Explanation:

There are two types of subscriptions: periodic and on-change. With periodic subscription, data is streamed out to the destination at the configured interval. It continuously sends data for the lifetime of that subscription. With on-change, data is published only when a change in the data occurs such as when an interface or OSPF neighbor goes down. https://developer.cisco.com/docs/iosxe/#! streaming-telemetry-quick-start-guide/streaming-telemetry

asked 07/10/2024
Shan Panikker
34 questions

Question 35

Report Export Collapse

What are two valid scaling techniques when an EIGRP network is designed that consists of more than 1000 routers? (Choose two.)

Use structured hierarchical topology with route summarization

Use structured hierarchical topology with route summarization

Used sub-second timers

Used sub-second timers

Use the distribute-list command to filter routes

Use the distribute-list command to filter routes

Modify delay parameters on the links

Modify delay parameters on the links

Implement multiple EIGRP autonomous systems

Implement multiple EIGRP autonomous systems

Suggested answer: A, E
asked 07/10/2024
Quratulain Damani
43 questions

Question 36

Report Export Collapse

Refer to the exhibit.

Cisco 300-420 image Question 36 111934 10072024005836000000

Which solution decreases the EIGRP convergence time?

Enable subsecond timers

Enable subsecond timers

Increase the hold time value

Increase the hold time value

Increase the dead timer value

Increase the dead timer value

Enable stub routing on the spokes

Enable stub routing on the spokes

Suggested answer: D
asked 07/10/2024
Patrick Thiel
40 questions

Question 37

Report Export Collapse

A router running ISIS is showing high CPU and bandwidth utilization. An engineer discovers that the router is configured as L1/L2 and has L1 and L2 neighbors. Which step optimizes the design to address the issue?

Make this router a DIS for each of the interfaces

Make this router a DIS for each of the interfaces

Disable the default behavior of advertising the default route on the L1/L2 router

Disable the default behavior of advertising the default route on the L1/L2 router

Configure the router to be either L1 or L2

Configure the router to be either L1 or L2

Configure each interface as either L1 or L2 circuit type

Configure each interface as either L1 or L2 circuit type

Suggested answer: D
asked 07/10/2024
Karen Charllotte Aglipay
34 questions

Question 38

Report Export Collapse

A network engineer must connect two sites across a public network using a secure tunneling technology that supports multicast traffic. Which technology must be chosen?

IPsec

IPsec

GRE

GRE

PPTP

PPTP

GRE over IPsec

GRE over IPsec

Suggested answer: D
asked 07/10/2024
Olugbenga Fagbohun
44 questions

Question 39

Report Export Collapse

Refer to the exhibit.

Cisco 300-420 image Question 39 111937 10072024005836000000

An engineer must optimize the traffic flow of the network. Which change provides a more efficient design between the access and the distribution layer?

Add a link between access switch A and access switch B

Add a link between access switch A and access switch B

Reconfigure the distribution switch A to become the HSRP Active

Reconfigure the distribution switch A to become the HSRP Active

Change the link between distribution switch A and distribution switch B to be a routed link

Change the link between distribution switch A and distribution switch B to be a routed link

Create an EtherChannel link between distribution switch A and distribution switch B

Create an EtherChannel link between distribution switch A and distribution switch B

Suggested answer: B
asked 07/10/2024
rami Awad
39 questions

Question 40

Report Export Collapse

When a first hop redundancy solution is designed, which protocol ensures that load balancing occurs over multiple routers using a single virtual IP address and multiple virtual MAC addresses?

GLBP

GLBP

IRDP

IRDP

VRRP

VRRP

HSRP

HSRP

Suggested answer: A
asked 07/10/2024
Ken Mak
47 questions
Total 240 questions
Go to page: of 24
Search

Related questions