A customer is looking for a network design with Cisco Hyperloctation using AP4800 for location tracking via a custom mobile app Issues appeared in the past with refresh rates for location updates. What needs to be implemented to meet these requirements?

Cisco CMX SDK in the location app

redundant CMX and fetch location in round-robin fashion.

How does AP failover priority for access points function when configured with priority 1 or 4?

When configured with priority 4, the access point is assigned with the highest priority level and it is marked as critical. This access point fails over before other access points with the lower priority when there is primary controller failure.

When configured with priority 1, the access point is assigned with the highest priority level and it is marked as critical. This access point fails over before other access points with the lower priority when there is primary controller failure.

When configured with priority 4, the access point is assigned with the highest priority level and it is marked as critical. This access point fails over before other access points with the lower priority when there is primary controller failure.

When configured with priority 4, the access point is assigned with the lowest priority level and it is marked as low. This access point fails over after other access points with the higher priority when there is primary controller failure.

When configured with priority 1, the access point is assigned with the medium priority level and it is marked as medium. This access point fails over after other access points with the higher priority when there is primary controller failure.

Refer to the exhibit. An enterprise is using wireless as the main network connectivity for clients. To ensure service continuity. a pair of controllers will be installed in a datacentre. An engineer is designing SSO on the pair of controllers. What needs to be included in the design to avoid having the secondary controller go into maintenance mode?

The connection between the redundancy ports is missing.

The Keep alive timer is too low. which causes synchronization problems.

The connection between the redundancy ports is missing.

The redundancy port must be the same subnet as the redundancy mgmt.

The Global Configuration of SSO is set to Disabled on the controller.

An enterprise is using two wireless controllers to support the wireless network. The data centre is located in the head office Each controller has a corporate WLAN configured with the nameCopr-NET390595865WLC-1 and Copr-NET6837l638WLC-2. The APs are installed using a round-robin approach to load balance the traffic. What should be changed on the configuration to optimize roaming?

Use the same WLAN name for the corporate network on both controllers.

Move all access points to one controller and use the other as N+1 HA.

Use the same WLAN name for the corporate network on both controllers.

Place the access points per floor on the same controller.

The wireless team must configure a new voice SSID for optimized roaming across multiple WLCs with Cisco 8821 phones. Which two settings accomplish this goal? (Choose two.)

Configure mobility groups between WLCs.

Use Cisco Centralized Key Management for authentication.

Configure mobility groups between WLCs.

Use Cisco Centralized Key Management for authentication.

Configure AP groups between WLCs.

Configure AVC profile on new SSID.

Use AVC to tag traffic voice traffic as best effort.

An engineer is designing an outdoor mesh network to cover several sports fields. The core of the network is located in a building at the entrance of a sports complex. Which type of antenna should be used with the RAP for backhaul connectivity?

2.4 GHz. 14-dBi omnidirectional antenna

5 GHz. 8-dBi omnidirectional antenna

2.4 GHz. 14-dBi omnidirectional antenna

A customer has restricted the AP and antenna combinations for a design to be limited to one model integrated antenna AP for carpeted spaces and one model external antenna AP with high gain antennas for industrial, maintenance, or storage areas. When moving between a carpeted area to an industrial area, the engineer forgets to change survey devices and surveys several APs. Which strategy will reduce the negative impact of the design?

Resurvey and adjust the design.

Deploy unsurveyed access points to the design.

Deploy the specified access points per area type.

Increase the Tx power on incorrectly surveyed access points.

An engineer is designing a wireless network to support high availability. The network will need to support the total number of APs and client SSO. Live services should continue to work without interruption during the failover Which two requirements need to be incorporated into the design to meet these needs? (Choose two.)

controller high availability pair with one of the WLCs having a valid AP count license

back-to-back direct connection between WLCs

controller high availability pair with one of the WLCs having a valid AP count license

back-to-back direct connection between WLCs

An engineer is designing a new wireless network. The network needs to meet these requirements: Which design approach should be taken?

2.4 GHz frequency band without channel bonding, to support 20 MHz channels

5 GHz frequency band with channel bonding, to support 40 MHz channels

5 GHz frequency band without channel bonding, to support 20 MHz channels

5 GHz frequency band with channel bonding, to support 80 MHz channels.

2.4 GHz frequency band without channel bonding, to support 20 MHz channels

A network engineer is designing a new wireless network. The network needs to have these characteristics: Which approach should be taken?

Deploy APs near each other for 5 GHz coverage, and enable the 2.4 GHz radios for all Aps.

Deploy APs near each other for 5 GHz coverage, and disable the 2A GHz radios for some Aps.

Deploy APs near each other for 2.4 GHz coverage, and disable the 5 GHz radios for all APs.

Deploy APs near each other for 5 GHz coverage, and enable the 2.4 GHz radios for all Aps.

Deploy APs near each other for 2.4 GHz coverage, and disable the 5 GHz radios for some APs.

A customer called with a requirement that internal clients must be on different subnets depending on the building they are in. All access points are operating in local mode and will not be modified, and this is a single controller solution. Which design approach creates the desired result?

Create AP groups for each desired location, map the correct VLANs to the internal SSID, and add the access points for that location.

Create an SSID place it to the desired VLAN under WLANs and configure 802.1x in ISE to assign the correct VLAN based on the SSID from which the client is authenticating

Create FlexConnect groups, place the access points in, and set the correct VLAN to SSID mapping based on location.

Create mobility anchors for the SSID and on the controller under the internal SSID create a foreign map to the desired VLAN based on location.

Two cisco 5520 wireless LAN controllers are managing all access points throughout the network. The WLCs are in different locations to provide geographical redundancy a mobility group has been configured on both WLCs and has a UP status on both controllers. The Aps in location A are statically configured to use controller A as the primary and controller B as the secondary. If the WLC in location A goes offline. The Aps successfully join the WLC in location, but they do not fail over to their primary configured controller. Which configuration task fixes the issue?

Enable AP fallback globally on the WLC

Configure the WLC in location A as primary using the CAPWAP AP Controller IP Address command on all the location A Access points.

Use DHCP Option 43 and specify WLC in location A as primary.

Enable AP fallback globally on the WLC

Change the AP Failover Priority to critical.

An AP is receiving 802.11 packets on its 802.11a radio with an RSSI value of -77 dBm. The current AP is part of an AP group that has been assigned an RF profile with RX-SOP set to Medium for 802.11a. Which action does the AP take with the packets?

Frames are decoded by the 5 GHz radio.

All frames are classified as non-Wi-Fi frames and are not decoded by the 5 GHz radio.

Frames are decoded by the 2.4 GHz radio.

All frames are classified as non-Wi-Fi frames and are not decoded by the 2.4 GHz radio.

Frames are decoded by the 5 GHz radio.

An engineer must repurpose a lab WLC appliance for use in the production environment of the enterprise. After the new WLC is configured with the information of the other WLC, the mobility tunnels are still not coming up. What is the reason?

The hardware platform is incompatible.

A firewall is blocking UDP port 16667 between the WLCs.

The WLC management interfaces are in the same VLAN.

The hardware platform is incompatible.

The mobility groups are different.

A wireless network consists of:* two IOS XE controllers installed in a data center* 9100 series APs* corporate and a guest WLANThe customer must high availability pair two Cisco WLCs for the client SSO. Which two design approaches must the engineer take to meet the requirement? (Choose two.)

Each WLC must have a unique redundancy management IP address.

The controllers must run the same operating system version.

The controllers must have the same number of licenses.

Both WLCs must have the same redundancy management IP address.

Both WLCs must have the same service port IP address.

Each WLC must have a unique redundancy management IP address.

The controllers must run the same operating system version.

A customer has this wireless design:* two Cisco Catalyst 9800 Series wireless controllers that are configured in a high-availability SSO cluster to manage the APs in a local office network* 100 APs in local mode that are registered to the high-availability cluster* one Catalyst 9800 Series wireless controller that is deployed as an anchor in a DMZ* a CAPWAP tunnel in UP state between the high-availability cluster and the anchor WLCThe customer wants the anchored traffic to remain up if a single WLC in the high-availability cluster fails. How must this requirement be incorporated into the design?

Configure the mobility MAC address for the high-availability cluster.

Configure the APs with the high-availability cluster as the primary base.

Deploy EMC APs as anchors and configure a high-availability cluster.

Create a separate EoIP tunnel for each WLC in the high-availability cluster.

Configure the mobility MAC address for the high-availability cluster.

Refer to the exhibit. A network engineer has identified that during a recent controller failure, several APs failed over to the tertiary controller instead of the secondary controller. The configuration from one of the APs is provided. Which design consideration led to the issue?

The secondary controller was at capacity.

The secondary controller is an SSO configuration.

The tertiary controller is an HA-SKU controller, so it took priority.

The tertiary controller is in the same subnet as the primary controller.

A customer has a single anchor WLC named Anchor A. Anchor A is in a DMZ and provides guest access. The customer wants to deploy an additional anchor controller named Anchor B to provide redundancy if Anchor A fails. Which design approach should be taken for the guest WLAN priority on the foreign WLC for each anchor WLC?

Set Anchor A to priority 1 and Anchor B to priority 1.

Set Anchor A to priority 3 and Anchor B to priority 3.

Set Anchor A to priority 3 and Anchor B to priority 1.

Set Anchor A to priority 1 and Anchor B to priority 1.

Set Anchor A to priority 1 and Anchor B to priority 3.

Refer to the exhibit. An engineer determined that during a recent controller failure, some APs did not failover to their secondary controller based on the network design, which has sufficient licenses for all APs. The controllers are not in a mobility group but have A records for their hostnames in DNS. Which setting needs to be addressed?

The secondary controller IP address is incorrect.

The controllers must be in the same mobility group.

The secondary controller IP address is incorrect.

DNS hostnames are required to be FQDN.

The AP failover priority was not set high enough.

APs in a remote office recently have been converted from local mode to FlexConnect to take advantage of the local switching. After the change, remote wireless users report voice quality issues and bad quality on wireless IP phones while roaming. A debug is performed, and it is noticed that the 802.11r Fast Transition is not working as expected, like on local mode AP, though the same WLAN configuration is in place. What is the cause of the issue regarding the FlexConnect APs?

They must be in a FlexConnect group to support 802.11r FT.

They do not support 802.11r FT.

They must be added into AP groups along with a common RF profile.

They must be in a FlexConnect group to support 802.11r FT.

They must be added to AP groups to support fast roaming methods.

An enterprise is using a Cisco AireOS controller and Wi-Fi 6 APs. The controller is installed in the head office, and the employees primarily use Apple OS devices. The APs broadcast WLAN ENT-WLAN406558520-1 for the employees and a guest WLAN with similar naming. What needs to be enabled on the controller to optimize roaming?

Aggregated Probe Response Optimization

During a wireless design all APs are mapped to designated controllers in case of a failure. The controllers are located in the same data center but in different racks. An AP failed over to a controller that was not defined on its High Availability tab. The customer does not want the AP to move back to its defined Cisco WLCs until they manually intervene. What needs to be addressed in the design?

Change the HA SKU secondary unit option.

Change the default mobility domain.

Cisco 300-425 Practice Test 3 - Free Online Exam Questions 81-120

During a post-deployment site Survey, issues are found with non wi-Fi interference. What should the engineer use to identify the source of the Interference?

Become a Premium Member for full access

Unlock Premium Member

Cisco 300-425 Practice Test 3

Question

Cisco 300-425 Practice Tests

Practice Tests