Home / Cisco / 300-430

Cisco 300-430 Practice Test - Questions Answers, Page 12

Question list

List of questions

Question 111

(0)

Which two events are outcomes of a successful RF jamming attack? (Choose two.)

Question 112

(0)

An engineer must create an account to log in to the CLI of an access point for troubleshooting. Which configuration on the WLC will accomplish this?

Question 113

(0)

A multitenant building contains known wireless networks in most of the suites. Rogues must be classified in the WLC. How are the competing wireless APs classified?

Question 114

(0)

An enterprise has recently deployed a voice and video solution available to all employees using AireOS controllers. The employees must use this service over their laptops, but users report poor serv

Question 115

(0)

Which customizable security report on Cisco Prime Infrastructure will show rogue APs detected since a point in time?

Question 116

(0)

After receiving an alert about a rogue AP, a network engineer logs into Cisco Prime Infrastructure and looks at the floor map where the AP that detected the rogue is located. The map is synchronized

Question 117

(0)

Refer to the exhibit. Which area indicates the greatest impact on the wireless network when viewing the Cisco CleanAir Zone of Impact map of interferers?

Question 118

(0)

A wireless network engineer must present a list of all rogue APs with a high severity score to senior management. Which report must be created in Cisco Prime Infrastructure to provide this informati

Question 119

(0)

An engineer must run a Client Traffic Stream Metrics report in Cisco Prime Infrastructure. Which task must be run before the report?

Question 120

(0)

What is the maximum time range that can be viewed on the Cisco DNA Center issues and alarms page?

Related questions

A network engineer needs to configure multicast in the network. The implementation will use multiple multicast groups and PIM routers. Which address provides automatic discovery of the best RP for each multicast group?

Refer to the exhibit. A network architect configured the Cisco Catalyst 9800 Series Controller to find out information on client types in the wireless network. RADIUS profiling is enabled so that the controller forwards the information about clients to a Cisco ISE server through vendor-specific RADIUS attributes. The ISE server is not profiling any data from the controller. Which configuration must be added in the blank in the code to accomplish the profiling on the Cisco 9800 Series controller?

DRAG DROP A wireless engineer wants to schedule monthly security reports in Cisco Prime infrastructure. Drag and drop the report the from the left onto the expected results when the report is generated on the right.

A wireless engineer must implement a corporate wireless network for a large company in the most efficient way possible. The wireless network must support 32 VLANs for 300 employees in different departments. Which solution must the engineer choose?

Refer to the exhibit. An engineer needs to configure location services in an office. The requirement is to use FastLocate and achieve higher locations refresh rates. Which location-based technique should be implemented?

Which two restrictions are in place with regards to configuring mDNS? (Choose two.)

A customer is deploying local web authentication. Which software application must be implemented on Cisco ISE to utilize as a directory service?

An IT administrator deployed an OEAP to the home of a remote user, but the OEAP cannot reach the WLC. Which two configuration settings must be completed before an OEAP is deployed successfully? (Choose two.)

A wireless network has been implemented to enable multicast video to be streamed reliably over the wireless link to the wireless users. After a client reports that the video is unable to stream, the administrator determines that the client is connecting at a data rate of 12 Mbps and is trying to stream to a valid multicast address on the network. Which two actions must be applied? (Choose two.)

What two actions must be taken by an engineer configuring wireless Identity-Based Networking for a WLAN to enable VLAN tagging? (Choose two.)

Question 111

Which two events are outcomes of a successful RF jamming attack? (Choose two.)

disruption of WLAN services

unauthentication association

deauthentication broadcast

deauthentication multicast

physical damage to AP hardware

Show Answer Comment (0)

Question 112

An engineer must create an account to log in to the CLI of an access point for troubleshooting. Which configuration on the WLC will accomplish this?

Allow New Telnet Sessions

ReadWrite User Access Mode

SNMP V3 User

Global Configuration Enable Password

Show Answer Comment (0)

Question 113

A multitenant building contains known wireless networks in most of the suites. Rogues must be classified in the WLC. How are the competing wireless APs classified?

adhoc

friendly

malicious

unclassified

Show Answer Comment (0)

An enterprise has recently deployed a voice and video solution available to all employees using AireOS controllers. The employees must use this service over their laptops, but users report poor service when connected to the wireless network. The programs that consume bandwidth must be identified and restricted. Which configuration on the WLAN aids in recognizing the traffic?

NetFlow Monitor

AVC Profile

QoS Profile

Application Visibility

Show Answer Comment (0)

Question 115

Which customizable security report on Cisco Prime Infrastructure will show rogue APs detected since a point in time?

Network Summary

Rogue APs Events

New Rogue APs

Rogue APs Count Summary

Show Answer Comment (0)

Question 116

After receiving an alert about a rogue AP, a network engineer logs into Cisco Prime Infrastructure and looks at the floor map where the AP that detected the rogue is located. The map is synchronized with a mobility services engine that determines that the rogue device is actually inside the campus.

The engineer determines that the rogue is a security threat and decides to stop if from broadcasting inside the enterprise wireless network. What is the fastest way to disable the rogue?

Go to the location where the rogue device is indicated to be and disable the power.

Create an SSID similar to the rogue to disable clients from connecting to it.

Update the status of the rogue in Cisco Prime Infrastructure to contained.

Classify the rogue as malicious in Cisco Prime Infrastructure.

Show Answer Comment (0)

Question 117

Refer to the exhibit.

Which area indicates the greatest impact on the wireless network when viewing the Cisco CleanAir Zone of Impact map of interferers?

Show Answer Comment (0)

Question 118

A wireless network engineer must present a list of all rogue APs with a high severity score to senior management. Which report must be created in Cisco Prime Infrastructure to provide this information?

Rogue AP Count Summary

New Rogue APs

Rogue AP Events

Rogue APs

Show Answer Comment (0)