A company is deploying an Avaya Session Border Controller for Enterprise (SBCE) for their Remote Workers only. The Remote Workers use 9640 hard phones which need to have 46xxsettings.txt downloaded to them.What is the minimum number of IP-addresses they need to assign to their private and public Network Interface Cards (NICs)?

1 IP-address to their private NIC, and 1 IP-address to their public NIC.

2 IP-addresses to their private NIC, and 1 IP-address to their public NIC.

1 IP-address to their private NIC, and 2 IP-addresses to their public NIC.

2 IP-addresses to their private NIC, and 2 IP-addresses to their public NIC.

After a new implementation the customer began to experience dropped calls and an ‘all lines busy’ error condition. The carrier confirmed their service was operational and all lines tested came back good. After contacting Avaya, support confirmed there were more calls being presented than the telephone switch could handle.Which pre-implementation step was omitted?

correct licensing specifications

Which three standards does the Avaya Aura® Application Enablement Services (AES) support? (Choose three.)

Computer Supported Telecommunications Applications (CSTA)

Media Stream Reservation Protocol (MSRP)

A customer calls Avaya support because their 3rd party SIP telephones are not working. Support is able to confirm that the telephones are not supported and do not integrate with Communication Manager or Session Manager. Which two pre-implementation steps were omitted? (Choose two.)

Provide accurate licensing specification.

Upgrade Communication and Session Manager.

Test all third-party equipment and software.

Provide accurate licensing specification.

Access support.avaya.com to verify customer systems compatibility.

Upgrade Communication and Session Manager.

Which three statements are true about Avaya Aura® Messaging (AAM)?(Choose three.)

AAM can run on Avaya-provided hardware that runs Linux® and Avaya Aura® System Platform, or VMware in a virtualized environment.

You can choose to use the Avaya Message Store or Microsoft Exchange Store.

AAM Multi-Server configuration separates Application Servers from Avaya Message Store.

20 Voice Ports are always reserved for retrieving messages.

AAM can run on Avaya-provided hardware that runs Linux® and Avaya Aura® System Platform, or VMware in a virtualized environment.

You can choose to use the Avaya Message Store or Microsoft Exchange Store.

AAM Multi-Server configuration separates Application Servers from Avaya Message Store.

Each message application server allows for up to 100 simultaneous SIP or H323 sessions, with 300 active ports permitted per Voice Mail Domain (VMD).

The WebRTC snap-in is showing a yellow caution icon underLicense Mode.What does this error mode indicate?

There is a license error but the snap-in continues to function.

The license was installed incorrectly.

The license 30 day grace period has expired.

There is a license error but the snap-in continues to function.

The snap-in license has expired and is out of service.

The Entity Monitoring column on the Session Manager Dashboard shows two figures per line.How should these two figures be interpreted?

the first number indicates the total number of links monitored, the second number indicates the number of links down

the first number indicates the number of retries, the second number indicates the total number of links monitored

the first number indicates the number of unmonitored links, the second number indicates the total number of monitored links

the first number indicates the total number of links monitored, the second number indicates the number of links down

the first number indicates the number of links down, the second number indicates the total number of links monitored

Which two methods can be used to determine the status of the Switch/CTI Link between Avaya Aura® Communication Manager (CM) and Avaya Aura® Application Enablement Services (AES)? (Choose two.)

Run the status aesvcs cti-link command on CM.

In Avaya Aura® 7 the Avaya Session Border Controller for Enterprise (SBCE) license is installed on an external WebLM server and the EMS points to the WebLM server using a URL.What is the correct syntax of that URL where 135.60.232.41 is the IP address of the WebLM server?

https://135.60.232.41:8443/WebLM/LicenseServer

https://135.60.232.41:8080/LicenseServer

https://135.60.232.41:52233/WebLM/LicenseServer

A Maintenance Engineer logs onto the Command Line Interface (CLI) of Avaya Aura® Messaging (AAM) and issues the vmstat command.What information will the display present?

information about the volatile memory

statistical information about voicemail boxes

information about the volatile memory

status information about the virtual machine

count of mailbox password violation attempts

What are the steps necessary to trace SIP messages going through the Avaya Session Border Controller for Enterprise (SBCE)?

Login to the EMS using a web browser, then access Device specific settings > Troubleshooting > Tracing, and click on Start traceSBC.

Login to the active Avaya Session Border Controller for Enterprise (SBCE) using SSH port 22, issue the su – root command, and then execute the traceSBC command.

Login to the EMS using port SSH 222, issue the sudo su command, and then execute the traceSBC command.

Login to the active Avaya Session Border Controller for Enterprise (SBCE) using SSH port 222, issue the sudo su command, and then execute the traceSBC command.

Which two trace tools are available for Session Manager?(Choose two.)

the traceSM command on the Session Manager Command Line Interface

the CallTrace command on the Session Manager Command Line Interface

the traceSM command on the Session Manager Command Line Interface

Trace Viewer in the System Manager GUI

the List trace command on the Session Manager Command Line Interface

Which types of certificates can be verified from the Avaya Aura® Application Enablement Services (AES) web console?

default certificates and Avaya server certificates

common a default Avaya SIP certificates

common and default Avaya server certificates

default certificates and Avaya server certificates

Avaya Aura® Messaging (AAM) needs to communicate with Avaya Aura® Session Manager (SM) whose identity certificates have been signed by Avaya Aura® System Manager (SMGR) Certificate Authority (CA).How does AAM get a copy of the Trusted SMGR CA Certificate?

The certificate installs as a result of running ‘initTM –f’.

The certificate is retrieved from SMGR automatically when AAM services are started.

The certificate needs to be manually installed.

The certificate installs as a result of running ‘initTM –f’.

The certificate installs as a result of the enrollment process.

What is the way to check the version of Presence Services snap-in installed on the AvayaBreeze™ platform?

Using Avaya Aura® System Manager (SMGR) Navigate to Elements > Engagement Development Platform > Server Administration, and read the Version displayed.

Using Avaya Aura® System Manager (SMGR) Navigate to Elements > Engagement Development Platform > Server Management, and read the Version displayed.

Using PuTTY SSH to the Avaya Breeze™ platform, login as cust, then execute the swversion command.

Using PuTTY SSH to the Avaya Breeze™ platform, login as cust, then execute the swversion– PresenceServices command.

Which method can be used to verify the Client and TSAPI services have been administered correctly?

The TSAPI test is call initiated within the TSAPI web interface > TSAPI Monitoring Tool menu.

The TSAPI test is call initiated from CTI endpoints using SIP telephones.

The TSAPI test is call initialed from within Avaya Aura® Communication Manager (CM) command line using the test TSAPI interface command.

The TSAPI test is call initiated within the TSAPI web interface > TSAPI Monitoring Tool menu.

The TSAPI test is call initiated within the Utilities > Diagnostics > AE ServiceTSAPI Test menu.

After upgrading Avaya Aura® Application Enablement Services (AES), the customer’s CTI application does not seem to be working. Which two methods can be used to verify AES system status? (Choose two.)

Access the AES command line, and run the status aesvcs cti-link command.

Access the AES web console, and view the services status in the AES menu.

Access the TSAPI web interface to monitor AES.

Access the AES command line, and run the status aesvcs cti-link command.

Access the AES web console, and view the services status in the AES menu.

Access Communication Manager (SAT), and run the statapp command to view AES services status.

Using Communication Manager’s System Administration Terminal (SAT), run the status aesvcs cti-link command to see the service state.

Refer to the exhibit.In the Cluster Administration screen of a PresenceServices cluster, when you try to change the cluster state to Accept New Service, you receive the error:Servers that are not in License Restricted mode assigned to the cluster are below the Minimum number of required servers.You check that a server has been administered under Engagement Development Platform > Server Administration which shows green check under License Mode, and a System State of Denying.Which action needs to be taken to solve this problem?

Under Engagement Development Platform > Server Administration, select the server and change the System State to Accept New Service, then return to the Cluster Administration screen and set the cluster to Accept New Service.

Edit the Cluster, access the Servers tab, and assign the server to the cluster; then set the cluster to Accept New Service.

Under Engagement Development Platform > Server Administration, select the server and change the System State to Accept New Service, then return to the Cluster Administration screen and set the cluster to Accept New Service.

Obtain and install an Avaya Breeze™ license on webLM with more instances of Avaya Breeze™ nodes.

Edit the cluster to change the cluster profile from Core Platform to General Purpose.

How can you enable all levels of the log, including debug, to be dumped into the ps.log file?

Web browse to Avaya Aura® System Manager (SMGR), navigate to Services > Events > Logs > Log Settings, then enter PresenceServices into the Logger filed, and enter ALL into Log Level.

Use SSH to the PresenceServices Avaya Breeze™ node and execute the ce dlogon PresenceServices command.

Use SSH to the PresenceServices Avaya Breeze™ node and execute the edp dlogon all command.

Use SSH to Avaya Aura® System Manager (SMGR) and execute the edp dlogon all command.

Where can an administrator go to validate the Breeze/WebRTC cluster is synchronized to Avaya Aura® System Manager (SMGR)?

the Replication menu in SMGR web interface

the Duplication menu in SMGR web interface

the Replication menu in WebRTC web interface

the Synchronization menu in Breeze web interface

the Replication menu in SMGR web interface

Which statement about Instant Message and Presence delivery to a SIP Remote Worker is true?

Presence notifications are sent to a Remote Worker via Session Manager and SBCE; IM is relayed from Breeze to Remote Worker via SBCE but without passing through Session Manager.

IM is sent/from to a Remote Worker via Session Manager and SBCE; Presence notifications are relayed from Breeze to Remote Worker via SBCE but without passing through Session Manager.

Presence and IM is delivered to SIP Remote Workers without passing through Session Manager.

Presence notifications and IM are sent to a Remote Worker via Session Manager and Avaya SBCE.

Presence notifications are sent to a Remote Worker via Session Manager and SBCE; IM is relayed from Breeze to Remote Worker via SBCE but without passing through Session Manager.

In Avaya Aura® 7, how are calls typically routed from Avaya Aura® Communication Manager (CM) to Avaya Aura® Messaging (AAM)?

Using SIP via Avaya Aura® Session Manager (SM), a dial pattern or regular expression forwards the call to AAM.

Using an in-directly routed H.323 trunk group between CM and AAM via Session Manager

Using a direct H323 trunk group between CM and AAM.

Using SIP via Avaya Aura® Session Manager (SM), AAM is built as a user with a Communication Profile and registry routing forwards the calls to AAM.

Using SIP via Avaya Aura® Session Manager (SM), a dial pattern or regular expression forwards the call to AAM.

In which way can you verify that STUN/TURN messages are being received from web browser at the Avaya Session Border Controller for Enterprise (SBCE)?

Enable traceSBC with the STUN/TURN option enabled.

Enable traceFM with the STUN/TURN option enabled.

Enable traceSBC with the STUN/TURN option enabled.

Enable traceHTTP with the STUN/TURN option enabled.

Enable debug logging on SBCE and look in ipcs.log.

Which three statements about Avaya Breeze ™ with WebRTC Snap-in are true?(Choose three.)

WebRTC uses a STUN/TURN server to relay WebRTC media from the public network through to the Avaya Aura® Media Server (AAMS).

WebRTC and Presence Services Snap-ins can co-reside on a General Purpose Cluster.

The WebRTC Snap-in will validate the authorization token created and encrypted by the web server.

WebRTC uses a STUN/TURN server to relay WebRTC media from the public network through to the Avaya Aura® Media Server (AAMS).

WebRTC and Presence Services Snap-ins can co-reside on a General Purpose Cluster.

The WebRTC Snap-in will validate the authorization token created and encrypted by the web server.

The web browser uses the “Cluster IP Address” to reach an Avaya Breeze ™ node when making a WebRTC call.

A customer reports that they cannot place WebRTC calls. You discover there is a problem with communication between Avaya Breeze ™ and the Avaya Aura® Media Server (AAMS).Where in Avaya Breeze ™ do you set/check the User ID for Restful TLS authentication?

Use the System Manager (SMGR) web GUI to access Breeze > Cluster Administration > General > Cluster Attributes

Use the System Manager (SMGR) web GUI to access Breeze > Configuration > Avaya Aura Media Server

Use the System Manager (SMGR) web GUI to access Breeze > Cluster Administration > General > Cluster Attributes

Use the System Manager (SMGR) web GUI to access Breeze > Configuration > Attributes

Use the System Manager (SMGR) web GUI to access Breeze > Server Administration > Dashboard

Which statement about Avaya Session Border Controller (SBC) is true?

The Avaya SBC is the enabling and secure pivot point for SIP Communications in and out of the Enterprise.

The Avaya SBC secures and authenticates Integrated Services Digital network (ISDN) calls placed to/from the Public Switched Telephone Network (PSTN).

The Avaya SBC is the enabling and secure pivot point for SIP Communications in and out of the Enterprise.

The Avaya SBC is a service within System Manager (SMGR) to support deployments.

The Avaya SBC is the enabling and secure pivot point for H.323 Communications in and out of the Enterprise.

A technician is trying to access the Avaya Aura ® Media Server (AAMS) after receiving a troubleshooting ticket. After failing to enter the system using different web browsers, the technician realizes the incorrect URL was being used.Which URL must be used to access the AAMS web page?

https: AAMS FQDN or IP address:8443/emlogin

http: AAMS FQDN or IP address:8443/emlogin

https: AAMS FQDN or IP address:443/emlogin

https: SMGR FQDN or IP address:8443/emlogin

Refer to the exhibit.In the Cluster Administration screen of a PresenceServices cluster, when you try to change the cluster state to Accept New Service, you receive the error:Servers that are not in License Restricted mode assigned to the cluster are below the Minimum number of required servers.You check that a server has been administered under Breeze > Server Administration which shows green check under License Mode, and a System State of Denying.Which action needs to be taken to solve this problem?

Under Avaya Breeze > Server Administration, select the server and change the System State to Accept New Service, then return to the Cluster Administration screen and set the cluster to Accept New Service.

Edit the Cluster, access the Servers tab, and assign the server to the cluster; then set the cluster to Accept New Service.

Under Avaya Breeze > Server Administration, select the server and change the System State to Accept New Service, then return to the Cluster Administration screen and set the cluster to Accept New Service.

Obtain and install an Avaya Breeze™ license on webLM with more instances of Avaya Breeze™ nodes.

Edit the cluster to change the cluster profile from Core Platform to General Purpose.

In which way can you check the version of Presence Services snap-in installed on the Avaya Breeze ™ platform?

Use Avaya Aura ® System Manager and navigate to Elements > Breeze > Service Management > Services, and read the version displayed.

Use puTTY SSH to the Avaya Breeze ™ platform, login as cust, then execute the swversion command.

Use Avaya Aura ® System Manager and navigate to Elements > Breeze > Server Administration, and read the version displayed.

Use Avaya Aura ® System Manager and navigate to Elements > Breeze > Service Management > Services, and read the version displayed.

Use puTTY SSH to the Avaya Breeze™ platform, login as cust, then execute the swversion – PresenceServices command.

Avaya 7230X Practice Test 2 - Free Online Exam Prep & Questions

On the Avaya Session Border Controller for Enterprise (SBCE), which tool would you use to view WebRTC messages coming through SBCE?

Become a Premium Member for full access

Unlock Premium Member

Avaya 7230X Practice Test 2

Question

Avaya 7230X Practice Tests

Practice Tests