What is an important consideration when connecting Dell PowerScale Gen6 nodes to external power?

Connect both cables of each node to different external power feeds.

Cable each node in a node pair to a different PDU.

Cable all nodes to the external power feeds before connecting switch power cables.

The total power load for all nodes in the rack should not exceed 100% of the branch circuit rating.

Connect both cables of each node to different external power feeds.

A customer is planning to expand a Dell PowerScale Gen5 cluster with H500 nodes What is a consideration?

A minimum of one H500 chassis is needed.

A minimum of three H500 chassis are needed.

All new nodes must be on the network.

A minimum of four H500 nodes are needed.

A minimum of one H500 chassis is needed.

Which are configured during the Configuration Wizard process?

Date and time Secure Remote Services

Contact information Secure Remote Services

Date and time Secure Remote Services

A company must ensure their PowerScale cluster can handle many active client connections. What must they do when designing their system?

Include a Leaf-Spine backend network

Which items are FRUs on a Dell EMC PowerScale Gen 6.5 node?

SSD, power supply, and front-end NIC

DIMM, system battery, and front-end NIC

DIMM, back-end NIC, and power supply

Which document was replaced by the PEQ?

Site Preparation and Planning Guide

Supportability and Compatibility Guide

Which Dell EMC PowerScale Gen 6 components are considered CRUs?

SSD, power supply, disk drive, and bezel

SSD, power supply, fan, and bezel

Back-end switch, power supply, disk drive, and bezel

SSD, power supply, disk drive, and bezel

SSD, memory card, disk drive, and bezel

A cluster consists of H400 nodes. A200 nodes, and tour Gen6 bays available tor expansion. An engineer plans to open bays.What is the result?

A300 nodes can be added and become members of the A200 node pool through the compatibility mode.

A300 nodes cannot be installed in this cluster.

A300 nodes can be added, and a new A300 node pool is created.

A300 nodes can be added and become members of the H400 node pool through the compatibility mode.

A platform engineer cables, powers up, and creates a new cluster of F600 nodes. While performing verification checks, no clients can access the cluster and the engineer cannot ping the nodes.What is the probable issue?

Nodes were connected to the management ports.

Manual reboot was not done following the cluster join.

Network was connected to the F600 rNDC ports.

Nodes were connected to the management ports.

Internal network was cabled improperly.

A platform engineer is building a new Dell EMC PowerScale cluster. The configuration wizard prompts to configure int-a.What is a consideration when configuring int-a?

Must be on a separate subnet from int-b.

Must be on the same subnet as int-b.

Must use the same subnet as groupnet0, subnet0.

Must be on a separate subnet from int-b.

Must use the same subnet as node 1, ext-1.

A platform engineer is connecting a new Dell EMC PowerScale F600 node to the back-end switch.How should the back-end cable be connected?

From PCIe slot 1 to the back-end Ethernet switch.

From PCIe slot 3 to the back-end InfiniBand switch.

From PCIe slot 1 to the back-end Ethernet switch.

From PCIe slot 1 to the back-end InfiniBand switch.

From PCIe slot 3 to the back-end Ethernet switch.

A Dell EMC PowerScale platform engineer is asked to reimage a node.What should they check before they start the reimage process?

Node has been SmartFailed and removed from the cluster.

The treedelete job has been run against the node.

Customer has redundant paths to their data.

Node has been SmartFailed and removed from the cluster.

SyncIQ job has been run to copy the node data.

What is a precaution when working with Dell EMC PowerScale equipment?

Use side stabilizers if the rack is not securely bolted to the floor.

Nodes can operate above 40 degrees C, but only for limited periods of time.

Connections to the branch circuit need not be properly grounded.

Use side stabilizers if the rack is not securely bolted to the floor.

The total rack load should not exceed 70% of the branch circuit rating.

A PowerScale customer is planning to expand a Dell EMC PowerScale Gen 5 cluster with H500 nodes.What is a consideration?

Minimum of three Gen 6 nodes are needed.

Only Gen 5 nodes can be added to the cluster.

Minimum of four H500 nodes are needed.

When a platform engineer disconnects and removes the power supply from a Dell EMC PowerScale Gen 6 node, they see an LED on the inside of the compute module.What does the LED indicate?

Pair node is supplying redundant power.

Power supply was not removed correctly and the node is shutting down.

Platform engineer has exactly two minutes to swap the power supply.

Visible LED is from the front panel of the node.

Pair node is supplying redundant power.

What should the platform engineer do to retain critical information when replacing a system board on a Dell EMC PowerScale F200 node?

Reinstall the PowerScale license

What is the purpose of SolVe Desktop?

Provide centralized access to step-by-step procedures

Gather logs from the cluster for analysis

Perform pre-upgrade checks on the cluster

Provide centralized access to step-by-step procedures

Provide access to the latest OneFS codes and firmware upgrades

Which resource provides up-to-date instructions to service a Dell EMC PowerScale system?

Dell Enterprise Configuration Services

A platform engineer has connected to a Dell EMC PowerScale F600 node using a serial connection. The session is unresponsive.What action should the engineer take?

Check the settings of the serial connection

Enable the serial port from the front panel menu

Connect to the primary node of the pair

Configure the cluster before connecting to the node

Check the settings of the serial connection

The SSD has failed in a Dell EMC PowerScale H400 node that has one SSD installed. A technician is asked to replace it.Where should the new drive be installed?

Left slot at the back of the node

Right slot at the back of the node

A platform engineer has just replaced a 3.5'' hard drive in a Dell EMC PowerScale Gen 6 drive sled.What should be the position of the drive sled handle before pushing the drive sled forward into the node chassis?

The drive sled does not have a handle

A platform engineer is at a customer site to replace a failed Dell EMC PowerScale Gen 6 node. After removing the compute module, they observe lit LEDs inside the removed node.What is the recommended response?

This is normal; they should continue with the procedure.

This is not normal; they need to shut down the partner node.

There is an internal electrical fault; they should call support.

The node is not yet completely shut down; they should wait.

This is normal; they should continue with the procedure.

A platform engineer needs to swap an NVDIMM battery. What prerequisite conditions are required to prevent data loss when removing the NVDIMM battery?

Node, LEDs on the node, LEDs on the NVDIMM, and LEDs on the NVDIMM battery must be off

None -- the NVDIMM battery is hot-swappable

The node is switched off and must be removed from the power feed

LEDs on the NVDIMM battery must be off

Node, LEDs on the node, LEDs on the NVDIMM, and LEDs on the NVDIMM battery must be off

What are the three phases of Dell EMC PowerScale implementation?

Planning, Implementation, Handover

Implementation, Functional review, Handover

Implementation, Documentation, Handover

Planning, Implementation, Handover

Planning, Implementation, Acceptance

Refer to the exhibit, which shows the rear of the Dell EMC PowerScale Gen 6 node. What is the function of the item associated with Callout 4?

Front-end Ethernet connectivity

Back-end and front-end Ethernet connectivity

Back-end InfiniBand and Ethernet connectivity

Front-end Ethernet connectivity

Back-end InfiniBand or Ethernet connectivity

DELL D-PSC-MN-01 Practice Test 2 - Free Online Exam Questions 41-80

A platform engineer does not have a Flash drive available.

How can they reimage a Dell PowerScale node?

Become a Premium Member for full access

Unlock Premium Member

DELL D-PSC-MN-01 Practice Test 2

Question

DELL D-PSC-MN-01 Practice Tests

Practice Tests