Which option is used to change a RecoverPoint with VNX(SE) to a RecoverPoint/EX configuration in the Deployment Manager Convert wizard?

Conversion to RecoverPoint with VNX(SE)

Which type of RecoverPoint Consistency Group contains both active and standby production copies?

Any group with multiple remote copies

A VPLEX distributed device has been configured as a production copy in a MetroPoint Consistency Group. However, a fracture has occurred between the two VPLEXclusters.What is the expected behavior of the RecoverPoint replication?

Replication will continue through the VPLEX winner site

Replication to the losing site will mark all writes and distribute them when the distributed device fracture is restored

Replication will continue through the VPLEX winner site

Replication will pause until the distributed device fracture is resolved

Replication continues to both clusters as the distributed device fracture does not impact replication

You are deploying a new RecoverPoint cluster using a VPLEX array; however, you need to determine where to locate the Repository volume. What is the recommended location for the Repository volume?

On the VPLEX as a virtual volume

On the VPLEX as a metadata volume

On the VPLEX as a distributed volume

On the VPLEX as a virtual volume

An organization is hosting storage protection solutions for multiple companies. Their solutions are based on a single VNX array. What is the maximum number ofRecoverPoint clusters that can be deployed by the organization?

Eight clusters, assuming each LUN is attached to only one cluster at a time

Five clusters, assuming only vRPAs are used

Eight clusters, assuming each LUN is replicated across the clusters

Eight clusters, assuming each LUN is attached to only one cluster at a time

Six clusters, assuming each LUN is attached to only one cluster at a time

Which environment settings can be changed in the System Modification wizard for an RPA connected to a VNX, VMAX, or a VPLEX?

RecoverPoint cluster name, Time zone, and DNS server

VMAX credentials, Time zone, and DNS server

RecoverPoint cluster name, Time zone, and DNS server

VPLEX cluster name, Time zone, and DNS server

VNX cluster name, Time zone, and DNS server

An organization plans to connect three different sites over IP using a RecoverPoint cluster at each site. However, the cluster fails to connect. The network team has determined that the required IP routing and WAN connectivity is in place. The desired routing information is added while running the Deployment Manager wizard.What is a possible cause for the failure?

Jumbo frames are not enabled on the IP network

Secondary sites are on different network subnets

Jumbo frames are not enabled on the IP network

boxmgmt password is different at the secondary sites

Which factors should be considered when using Deployment Manager to connect a RecoverPoint cluster to an existing cluster?

License Type and Connectivity Protocol

Connectivity Protocol and RPA Type

License Type and Connectivity Protocol

Connectivity Protocol and Number of RPAs

During the write phase of RecoverPoint replication, when does the RPA send an acknowledgement back to the write splitter?

As soon as the RPA receives the write

After the distribution phase has completed

After the RPA has received an acknowledgement from all copies involved with replication

After the local RPA has received an acknowledgement from the remote RPA

The production and remote copies of a Consistency Group are hosted on XtremlO arrays. During application testing of the remote copy, the Image Access log capacity does not advance.Why is the Image Access log capacity static?

Application writes are to an XtremlO snapshot and are not stored in the Journal

Failover has not completed so the writes have not been distributed to the Journal

Application writes are to an XtremlO snapshot and are not stored in the Journal

Journals on XtremlO arrays are virtual and do not track the writes

Application writes are stored in RPA memory when using the XtremlO array

You are performing a RecoverPoint cluster installation using Deployment Manager. The new cluster is using physical RPAs. During the 'Connectivity Settings' step ofDeployment Manager, which interface(s) can be configured to use DHCP?

Cluster management Explanation: In the RecoverPoint Deployment Manager, the Cluster management interface can be configured to use DHCP. This setting allows the cluster management interface to automatically obtain an IP address from a DHCP server, simplifying network configuration.Reference: Dell RecoverPoint for Virtual Machines 6.0.1 vSphere HTML5 Plugin Administrator's Guide, Chapter on Deployment and Initial Configuration.

A RecoverPoint administrator performs a Consistency Group failover to a remote copy. What happens to the point-in-time images stored in the copy Journal after the copy becomes production?

Images are replicated to the new copy Journal

Images are replicated to the new production Journal

DELL D-RP-DY-A-24 Practice Test 2 - Free Online Exam Prep & Questions

DRAG DROP

What is the correct sequence of steps to implement RecoverPoint with XtremIO?

Become a Premium Member for full access

Unlock Premium Member

DELL D-RP-DY-A-24 Practice Test 2

Question

DELL D-RP-DY-A-24 Practice Tests

Practice Tests