Ask Question
Fortinet FCP_FAZ_AD-7.4 Practice Test - Questions Answers, Page 4
Add to Whishlist
List of questions
Question 31
Which process is responsible for enforcing the log file size?
oftpd
miglogd
sqlplugind
logfiled
The logfiled process is responsible for enforcing log file size and managing log rotation on FortiAnalyzer. It ensures that log files do not exceed the configured size limits and handles the creation and rotation of new log files when necessary.
Question 32
Refer to the exhibit, which shows the HA configuration settings of a FortiAnalyzer device.
The administrator wants to join this FortiAnalyzer to an existing HA cluster. What can you conclude from the configuration displayed?
After joining the cluster, this FortiAnalyzer will forward received logs to its peers.
This FortiAnalyzer will trigger a failover after losing communication with its peers for 10 seconds.
This FortiAnalyzer is configured to route HA traffic through a gateway.
This FortiAnalyzer will join the existing HA cluster as the secondary.
The 'Preferred Role' is set to Secondary, which means this FortiAnalyzer is configured to join the cluster as the secondary unit in an Active-Passive HA configuration. Other settings, such as the peer IP and serial number, confirm its setup to communicate with the primary unit.
Question 33
What does the disk status Degraded mean for RAID management?
The hard drive is no longer being used by the RAID controller.
One or more drives are missing from the FortiAnalyzer unit.
The device is writing data to the disk to restore the volume to an optimal state.
FortiAnalyzer determined that the parity data in the disk is not valid.
When the RAID status is Degraded, it typically indicates that one or more drives in the RAID array have failed or are missing, causing the RAID array to operate with reduced redundancy. In this state, the array is still functioning, but it's at risk because the fault tolerance provided by RAID is compromised.
Question 34
The connection status of a new device on FortiAnalyzer is listed as Unauthorized.
What does that status mean?
It is a device whose registration has not yet been accepted in FortiAnalvzer.
It is a device that has not yet been assigned an ADOM.
It is a device that is waiting for you to configure a pre-shared key.
It is a device that FortiAnalvzer does not support.
The 'Unauthorized' status indicates that the device has been discovered or attempted to connect but has not yet been authorized for management by FortiAnalyzer. It requires an administrator to approve or authorize the device before it can be fully managed.
Question 35
Which two statements regarding ADOM modes are true? (Choose two.)
In normal mode, the disk quota of the ADOM is fixed and cannot be modified, but in advanced mode, the disk quota of the ADOM is flexible.
You can change ADOM modes only through the CLI.
In an advanced mode ADOM, you can assign FortiGate VDOMs from a single FortiGate device to multiple FortiAnalyzer ADOMs.
Normal mode is the default ADOM mode.
Question 36
What are the operating modes of FortiAnalyzer? (Choose two)
Standalone
Manager
Analyzer
Collector
Question 37
Which statements are correct regarding FortiAnalyzer reports? (Choose two)
FortiAnalyzer provides the ability to create custom reports.
FortiAnalyzer glows you to schedule reports to run.
FortiAnalyzer includes pre-defined reports only.
FortiAnalyzer allows reporting for FortiGate devices only.
Question 38
Which tabs do not appear when FortiAnalyzer is operating in Collector mode?
FortiView
Event Management
Device Manger
Reporting
Question 39
In Log View, you can use the Chart Builder feature to build a dataset and chart based on the filtered search results.
Similarly, which feature you can use for FortiView?
Export to Report Chart
Export to PDF
Export to Chart Builder
Export to Custom Chart
Similar to the Chart Builder feature in Log View, you can export a chart from a FortiView. The chart export includes any filters you set on the FortiView. FortiAnalyzer_7.0_Study_Guide-Online pag. 292.
Question 40
What can you do on FortiAnalyzer to restrict administrative access from specific locations?
Configure trusted hosts for that administrator.
Enable geo-location services on accessible interface.
Configure two-factor authentication with a remote RADIUS server.
Configure an ADOM for respective location.
Related questions
Export
If you didn't receive an email within 5 minutes, you should submit a support request to [email protected].
|
BASIC - 1 Month
$
10
Full latest questions
No CAPTCHA
New Updates
Export to VPLUS
Export to PDF - All questions
Team support
|
PLUS - 2 Months
$
15
Full latest questions
No CAPTCHA
New Updates
Export to VPLUS
Export to PDF - All questions
Team support
|
PRO - 6 Months
$
40
Full latest questions
No CAPTCHA
New Updates
Export to VPLUS
Export to PDF - All questions
Team support
|
Full latest questions
No CAPTCHA
New Updates
Export to VPLUS
Export to PDF - All questions
Team support
Full latest questions
No CAPTCHA
New Updates
Export to VPLUS
Export to PDF - All questions
Team support
Full latest questions
No CAPTCHA
New Updates
Export to VPLUS
Export to PDF - All questions
Team support
Selling illegal goods, money scams etc.
Serious attack on a group.
Harassing an individual (including doxing)
Threatening or glorifying violence or serious harm, including self-harm
Nudity/Sexual content
Sexually explicit or suggestive imagery or writing involving minors
Sexually explicit or suggestive imagery or writing involving non-consenting adults or non-humans
Reusing content without attribution (link and blockquotes)
Not in English or has very bad formatting, grammar, and spelling
Author's credential is offensive, spam, or impersonation
Ex. Illegal content, incomplete question...
Question