Huawei H12-831_V1.0 Practice Test - Questions Answers, Page 3

List of questions
Question 21

An engineer uses two routers to test IPv6 services, and runs 0SPFv3 to implement IPv6 network interconnection. R1 is required to be able to access the loopback interface address of R2. The engineer checked the OSPFv3 routing table entry of R1, as shown in the figure, and found that there was no route to the loopback interface address of R2. Which of the following reasons could not be the cause?
R2 advertises the loopback interface into different OSPFv3 processes
R2 does not have 0SPFv3 enabled on the loopback interface
R2 does not use network to advertise loopback address in area 0
R2 is not configured with the Router ID used in the OSPFv3 process
Question 22

aboutOSPFWhich of the following statements is false?
For a pair of additional 0hers on an Ethernet link, it is normal to stop clearing in the 2-72 state
Stalling in ExStart state may be a bad match between neighbor routers
stagnantINThe it state indicates that the router has received the neighbor'sHello message. butHell messagedoes not include this routerOSPF Router ID
The two router databases are synchronized, SPFAn error occurred in the calculation, it must be because of the RouterID repeated
Question 23

In the same environment, engineers A and B execute the tracert command. The destination addresses are the same, but the paths are different. What are the possible reasons?
The phenomenon is abnormal, the device has an operating system failure
Engineer A's operation error
Engineer B's operation error
The destination port numbers of the UDR packets serving tracert are different, and the hashes reach different equivalent next hops.
Question 24

Which of the following is included in the routine collection of basic equipment information?
License information
Patch information
The software version the device is running
Whether the configuration is saved
Question 25

According to this picture, we can judge that R4 is on?
1 default route
2 equal-cost default routes
2 default routes with different costs
4 equivalent default routes
Question 26

Fill in Blanks
IGP converges faster than BGP, which may cause network traffic loss. By enabling the OSPF and BGP linkage feature of the device, the device can keep the OSPF and BGP linkage during the set linkage time.____The router makes the link metric value in the LSA advertised to be the maximum value, so as to inform other OSPF devices not to use this router to forward data, so as to avoid traffic loss. (Note: If English letters are involved, all uppercase)
STUBROUTER
Question 27

OSPF is deployed in a campus to achieve network interworking, and OSPF is also enabled on the GEO/0/2 interface of R3. Area1 is deployed as an NSSA area, and the device addresses are shown in the figure. An engineer configures a static route on R3 to access the loopback interface address of R4, and imports the static route in the 0SPF process. At this point, in the Type5 LSA received by R1, the forwarding address (FA) is____. (Note: Please fill in the IP address without mask)
(10.1.23.2)
Question 28

As shown in the figure, in a medium-sized network, BGP generally deploys dual RRs to improve R reliability. When deploying dual RRs, the Cluster IDs of the two RRs are generally set to be the same. The reason for this is
Prevent RR from receiving too many routes and causing insufficient memory
prevent suboptimal
prevent loops
Prevent the client from receiving too many routes and causing it to run out of memory
Question 29

According to this picture, you can judge
The optimal outgoing interface for R1 to access room 3000: FDEA::3 is GigabitEtherneto/0/1
R1 with 3000:FDEA::3 is IB6P neighbor
R1 has a TCP connection with 3000:FDEA::3
R1 learned route 3002 through IBGP::3/128
Question 30

Link LSAs of OSPFv3 are propagated throughout the area.
right
wrong
Question