HP HPE2-W09 Practice Test - Questions Answers, Page 8

NetEdit is a network management tool that allows you to configure, monitor, and troubleshoot ArubaOS-CX switches. NetEdit can send notifications of changes in network conditions to other services, such as email, using methods that define the service type and credentials. However, NetEdit does not use its internal email server to send notifications. NetEdit requires an external SMTP server to send email notifications, and the SMTP server address, port, username, and password must be configured in the email method1. Therefore, this does not correctly describe NetEdit's notification capabilities.

The status is Pending, which means that the ring is configured but not operational. The ring instance may be in one of the following states: Idle, Initializing, Pending, or Failed1. The Pending state indicates that the ring instance is waiting for a trigger event to become operational, such as a link failure or a manual command1. The status does not depend on whether the ring is enabled administratively or not. https://www.arubanetworks.com/techdocs/AOSCX/ 10.08/HTML/high_availability/Content/Chp_ERPS/ERPS_cmds/sho-erp-sta4.htm

Asymmetric IRB routes packets in the ingress VTEP and then bridges packets in the egress

VTEP1. This means that the ingress VTEP performs both Layer 2 and Layer 3 lookups, while the egress

VTEP performs only Layer 2 lookup1. The statement is false because it confuses routing with bridging in the egress VTEP.

A layer 2 VLAN is a single broadcast domain that works on the data link layer1. It cannot be assigned an IP address or attached to a VRF. A VRF requires a layer 3 interface that works on the network layer and can perform routing between different VLANs2. A layer 2 VLAN can only communicate within itself, not with other VLANs or routing domains1.

A GRE tunnel interface is a virtual interface that can encapsulate different network layer protocols inside point-to-point or point-to-multipoint links over an IP network1. It can be assigned an IP address and attached to a VRF. A VRF allows multiple instances of a routing table to co-exist within the same router2. By attaching a GRE tunnel interface to a VRF, you can isolate the traffic of that tunnel from other tunnels and routing domains2.

Switch-1 does not download its MAC forwarding table from Switch-2 when Switch-2 finishes booting. Switch-1 and Switch-2 are part of a VSX fabric, which is a high availability solution that provides redundancy and load balancing across a pair of switches1. When Switch-2 experiences a power failure, Switch-1 takes over the role of the primary member and continues to forward traffic1. When Switch-2 recovers, it synchronizes its configuration and state information from Switch-1, not the other way around1. The MAC forwarding table is part of the state information that is synchronized from the primary to the secondary member1.

Creating two ERPS instances for the ring and assigning different VLANs and different RPLs to each instance is part of a valid strategy for load sharing traffic across the links in an ERPS solution1. ERPS is a protocol that provides protection and recovery for Ethernet traffic in a ring topology1. It uses a RPL to block one of the links in the ring and prevent loops1. By creating two ERPS instances with different RPLs, you can use both links in the ring for different VLANs and achieve load sharing1.

Uploading firmware images to the NetEdit firmware repository is part of the process for using

NetEdit to update firmware on ArubaOS-CX switches1. NetEdit is a tool that allows you to manage and monitor multiple switches from a single interface1. It also provides a firmware repository where you can store firmware images for different switch models and versions1. You can use NetEdit to upload firmware images to the repository and then deploy them to the switches1.

Creating a conformance test to check that the firmware matches the desired version is part of the process for using NetEdit to update firmware on ArubaOS-CX switches1. NetEdit is a tool that allows you to manage and monitor multiple switches from a single interface1. It also provides a conformance feature that lets you create tests to verify that the switches comply with your desired configuration and firmware settings1. You can use NetEdit to create a conformance test to check that the firmware matches the desired version and then run it on the switches1.

https://asp.arubanetworks.com/downloads;products=Aruba%20Switches