You have created an OSPF neighbor configuration with ArubaOS-CX 8320 VSX and a third-party switch The OSPF peering falls. In the event togs you see the following entries.2020-10-28:03:14 20.371489|hpe-routlng|LOG_WARN|AMM|1/5jOSPFV2|OSPFV2iOSPF 268698624 Packet received with unexpected authentication type 2020-10-28:03:14.20.371503|hperouting| LOG_WARN|AMM|1/5|OSPFV2|OSPFV2|Expected authentication type = 0 Which statement is true about the above events?

The third-party switch should be configured with key chain authentication

The ArubaOS-CX switch requires plain-text authentication with OSPF.

The third-party switch should be configured with MD5 authentication

The ArubaOS-CX switch does not expect authentication with OSPF.

The third-party switch should be configured with key chain authentication

When applying me following access-Iist to an ArubaOS-CX 6300 switch: How does this ACL behave on the selected switch? (Select two.)

The tftp traffic to MANAGEMENT-SERVERS group is not logged to the event logs.

The denied tcp traffic to the MANAGEMENT-SERVERS group is not logged to event logs

The mp traffic to MANAGEMENT-SERVERS group is logged to me event logs

The tftp traffic to MANAGEMENT-SERVERS group is not logged to the event logs.

The snmp-trap traffic to MANAGEMENT-SERVERS is logged to the event togs.

The denied tcp traffic to the MANAGEMENT-SERVERS group is logged to event logs.

The denied tcp traffic to the MANAGEMENT-SERVERS group is not logged to event logs

The customer is considering Implemented the following VSX configuration that will host an Aruba mobility cluster servicing 9000 dual stack employee devices.The client's default gateways will be hosted on the VSX stack. The customer is seeking advice about how to ensure ArubaOS-CX VSX best practices have been applied. What advice can you offer the customer? (Select two)

Agg-1 and Agg-2's hardware forwarding table profile should be changed to "L3-agg''.

The keepalive subnet is misconfigured, it has an inappropriate address on Agg-1.

The ISL Bandwidth should be upgraded

Agg-1 and Agg-2's hardware forwarding table profile should be changed to "L3-agg''.

The -system-mac' of Agg-1 should be changed to an unused address from the unicast private address range

The vsx linkup-delay timer is unnecessarily high; it should be reduced to prevent excessive delay of packet forwarding when a VSX peer joins an existing master.

The Keepalive interface should be changed to interface LAG2 so there is redundancy through the mobility cluster.

The keepalive subnet is misconfigured, it has an inappropriate address on Agg-1.

(Scenarios may contain multiple errors which may or may not Impact the solution > Refer to the exhibit. An engineer has attempted to configure two pairs of switches in the referenced configuration it is required to implement VSX keep-alive at the aggregation layer.The ports of the ArubaOS-CS 8325 switches used for Agg01 and Agg02 are populated as follows: The configuration of switch AGG01 includes: VSX keep-alive is not working. Which modification should you make lo resolve the error condition?

Modify the Interface lag 2 command, removing "multi-chassis"

Edit interface 1/1/48, adding the command "vpn-instance KA"

Modify the Interface lag 2 command, removing "multi-chassis"

Modify the Keepalive peer 192.168.20.2 source 192 168.20.1 command, adding "vrf KA"

Edit the vsx-sync command, adding "keep-alive"

(Scenarios may contain multiple errors which may or may not impact the solution ) Refer to the exhibit. An engineer has attempted to configure two pairs of switches in the referenced configuration It is required to implement VSX at the aggregation layer The pons of the ArubaOS-CX 8325 switches used for Agg01 and Agg02 are populated as follows: The configuration of switch AGG01 includes The VSX cluster is not forming. Which modification should you make to resolve the error condition?

Modify the system interface-group 4 speed tOg command change "25g" to "10g"

Modify the keepalive peer 192.168 20.2 source 192 168.20 1 command, changing "vrf KA" to "vrf mgmt"

Edit the vsx-sync command, adding "keep-alive"

Modify the vsx definition, changing "inter-switch-link lag 2" to" inter-switch-link lag 256"

(Scenarios may contain multiple errors which may or may not impact the solution) Refer to the Exhibit. An engineer has attempted to configure two pairs of switches m the referenced configuration it Is required to implement Multi-Chassis Link Aggregation for each pair of switches The ports of the Aruba 8325 switches used for Agg01 and Agg02 are populated as follows The configuration includes: There is an error message stating "mismatched group speed" What should you add to the configuration to correct the error?

"speed 10-full" under interfaces 1/1/12 and 1/1/13

"system Interface-group 1 speed I0g"

"speed 10-full" under interfaces 1/1/12 and 1/1/13

"speed 40-full" under interfaces 1/1/49 and 1/1/50

An administrator has identified a denial of service attack that is stressing the management processor on the switch. Which actions can be applied to CoPP to mitigate the issue? (Select two.)

Regulate traffic from the OOBM Ethernet port

Apply multiple active polices for the classes of traffic

Create a policy that matches the payload of GRE traffic.

Regulate traffic from the OOBM Ethernet port

Apply multiple active polices for the classes of traffic

A customer would like to utilize some ArubaOS-CX 6300M switches to perform OSPF routing. All ports are routed, and ECMP is enabled, with other default parameters for OSPF. What will be the result of traffic sent from CLIENT-A to CUENT-B?

Traffic will be SW3 -> SW-1 -> sw-4 -> SW-2

Traffic will be SW3 -> SW-4 -> SW-2.

Traffic win be SW3 -> SW-1 -> sw-2.

Traffic will be SW3 -> SW-1 -> sw-4 -> SW-2

Traffic will be SW3 -> SW-1 -> Sw-2 & SW3 -> SW-4 -> SW-2

Which statement is true regarding IP-SLA?

ArubaOS-CX supports forever tests

ArubaOS-CX supports Doth SLA configuration through CU and by agents through the NAE.

ArubaOS-CX supports forever tests

ArubaOS-CX supports on-demand as well as forever tests.

The default and minimum probe interval for voip SLA is 180 seconds

Refer to the exhibit. Which statement is true?

Q1 and S1 are applied to all interfaces mat do not have a QoS override applied

To be effective, both Q1 and S1 still need to be applied to Interfaces

Q1 and S1 are applied to all interfaces.

Which statement is true regarding remote mirroring?

Per session multiple destination addresses can be configured

The same source/destination address can be used in multiple sessions.

Per session multiple destination addresses can be configured

The ArubaOS-CX switch supports a maximum of two mirroring sessions

When mirroring destination is tunnel, a DSCP value can be set on the tunnel

Which statement is true about NAE scripts'?

The System Resource Monitor is the only script Installed on the system by default.

The System Resource Monitor and Health Monitor a/e the only scripts installed on the system by default

No script is installed on the system by default.

The Health Monitor is the only script installed on the system by default.

Refer to the exhibit. Criteria

Configure Edge-2 with a route-map to 'set as-path prepend"' to apply 64516 two times to the neighbor for AS 64516.

All outbound traffic to AS 64516 prefers Edge-2 to AS 64516

All other outbound traffic prefers Edge-1 to AS 64513Given the customer connectivity depicted in the diagram which single change can be performed on Edge-2 to ensure the criteria are met?

Configure Edge-2 to set ebgp-multihop 3 for the neighbor for AS 64516.

Configure Edge-2 with a route-map to 'set as-path prepend"' to apply 64516 two times to the neighbor for AS 64516.

Configure Edge-2 to set the local preference for specific routes originating from AS 64516 to 200 and all other routes from AS 64516 to 50

Configure Edge-2 to set the weight on specific routes specific to AS 64516 to 1.

A client connected to Aruba CX 6300 on Port vt/2 Is having issues connecting to a remote destination 10 100 10 62 port 443. How should you get session-specific diagnostic information about this connection?

Use diag utilities tcpdump destination-prefix 10 100 10.62/32 to capture the session

Use diag utilities tcpdump desttnation-ip 10 10010.62 to capture the session

Use diag utilities tcpdump destination-prefix 10 100 10.62/32 to capture the session

Run tcpdump -interface "1/1/2" host 10.100 10.62 to capture the session

Enter diag-mode and execute tcpdump ip.addr==10.100.10.62.

Refer to the following configuration: How do you configure QoS policies for user traffic in conjunction with user roles in all wired access switches? (Select two)

in a RADIUS server with Aruba Vendor Specific Attribute (VSA) dictionary, you can add QoS policies for user roles.

Use NetEdit to replicate the configuration of QoS policies to all wired switches

in a RADIUS server with Aruba Vendor Specific Attribute (VSA) dictionary, you can add QoS policies for user roles.

With ClearPass and downloadable user roles, you can add QoS policies for user roles

QoS policies should be configured by the Mobility Controller when you need to set to all wired access switches

The customer has a requirement for creating security filtering for IPv4 and IPv6 traffic passing through an ArubaOS-CX 6400 switch. Which statement Is true about access-list on the selected switch model?

Routed interfaces can have only inbound ACLs

IPv4 and IPv6 entries can be used in one ACL with separate rules

Separate IPv4 and IPv6 ACLs need to be created for inbound and outbound traffic

Only one inbound or outbound ACL can be bound to an interface.

Routed interfaces can have only inbound ACLs

A customer would like to utilize some ArubaOS-CX 8325 switches to discard unwanted traffic to the IP address 10 20.30 40.You enter the following command on the switch:Ip route 10.20.30.40/32 blacWhat will be the result?

The switch will discard packets to the destined host silently

The switch will not discard packets to the destined host

The switch will discard packets to the destined host and create a tog message

The switch will discard packets to the destined host silently

The switch will discard packets to the destined host and return ICMP error to the sender.

After a Proof of Concept where NetEdit was used to troubleshoot the network, the customer agrees that NetEdit meets some of its technical goals.Which technical goals does NetEdit meet? (Select two.)

improve reliability of mission-critical applications

improve the network's scalability

When planning a new wired network solution for an organization, mere are technical goals that must be achieved to support the organization objectives and their applications and services.Which options are valid technical goals? (Select two.)

Transform the process of acquisition of a new network solution from a CAPEX to an OPEX model

Accelerate the ordering process of new network hardware.

Transform the process of acquisition of a new network solution from a CAPEX to an OPEX model

Replace hardware that is reaching end of support with a technology refresh.

Accelerate the ordering process of new network hardware.

A customer would like to utilize some ArubaOS-CX 6300F switches to perform OSPF routing. With the ports set up as routed ports, and default parameters for OSPF, which action is the simplest way to allow the fastest communication…

Utilize Equal-cost multi-path routing to aggregate more bandwidth on the WAN.

Set the OSPF cost parameters on every interface on every switch according to the Bandwidth or each link

Set the OSPF reference bandwidth to 10 or higher

Before designing a new network solution for a customer with between 2398 and 5264 employees, you should gamer Information from the customer about their wired network needs.What are valid questions to determine their wired network needs? (Select two.)

What is the current cabling deployed in the location?

How much do you plan to spend in the new wired network?

How experienced is your networking team?

What is the current cabling deployed in the location?

What are the current device capabilities and topology?

Do you plan to add new customer services?

How much do you plan to spend in the new wired network?

A customer with an ArubaOS-CX 6300M switch is having a performance issue on the network and has received complaints about users experiencing intermittent connectivity. After performing troubleshooting it is determined that many of the local websites on the LAN that users are unable to reach are resolved to an invalid MAC address.What are the minimum steps that should be performed to mitigate this condition? (Select two)

Implement arp ACLs to define trusted MAC address to IP bindings

Enable 'arp inspections on the end-user VLAN.

Implement arp ACLs to define trusted MAC address to IP bindings

Enable 'arp inspection' on the end-user physical ports

Enable 'arp inspections on the end-user VLAN.

Enable 'arp inspection untrusted on the end-user physical pons

The customer is implementing new ArubaOS-CX 6300 switches into an environment that has thirdparty switches and uses centralized authentication from Microsoft Active Directory and TACACS* servers What would be a valid configuration requirement for ArubaOS-CX switches for centralized user authentication?

Enabling the active directory VSA in the switch for radius authentication

Importing a TACACS server certificate for TLS authentication into the switch

Defining a TACACS server group for authentication in the switch configuration

Enabling the active directory VSA in the switch for radius authentication

Using a PAM extension for LDAP authentication with Active Directory Server.

A network administrator has deployed the following (partial) configuration: What is the effect of this policy?

Only ssh traffic to ip-address in VRF mgmt is restricted to 10 254 254 0/24 network

Only subnet 10.254.254.0/24 is allowed to communicate with ip-addresses configured on VRF mgmt

COPP traffic is restricted to subnet 10.254.254 0/24

Only ssh traffic to ip-address in VRF mgmt is restricted to 10 254 254 0/24 network

Only subnet 10.254 2540/24 is allowed to communicate with CoPP-addresses configured on VRF mgmt

A customer is installing a new ArubaOS-CX switch The customer does not change the factory default QoS configuration The switch receives an 802.1Q tagged VOIP frame on a port The header contains a DSCP value of EF(46) and the frame has an 802 ip value of 5 How will the switch forward the frame?

Forwards it based on the DSCP value in the frame

The switch trusts the settings and It forwards the frame with the current settings

Forwards it based on the 802 ip value in the frame

Forwards the frame with best effort forwarding

Company A and Company B are merging their BGP routed networks The companies have overlapping IP ranges and security concerns during the migration phase. Which Aruba CX 8325 functionality would help the merging of networks in a secure way?

Use of Aruba Gateway appliance to control the routes between merged networks

Use of ACL's to separate the company networks at the VLAN level

Use of Aruba Gateway appliance to control the routes between merged networks

Use of vsf capable switch to integrate the routing

Use of virtual route forwarding and BGP route leaking

A customer with an ArubaOS-CX 6300M switch is having a performance issue on the network and has received complaints about users experiencing intermittent connectivity. After performing troubleshooting it is determined that many of the local websites on the LAN that users are unable to reach are resolved to an invalid MAC address What are the minimum steps that should be performed to mitigate this condition? (Select two.)

Implement ARP ACLs to define trusted MAC address to IP bindings

Enable 'arp inspection' on the end-user VLAN

Implement ARP ACLs to define trusted MAC address to IP bindings

Enable 'arp inspection' on the end-user physical ports

Enable 'arp inspection untrusted' on the end-user physical ports

Enable 'arp inspection' on the end-user VLAN

You have removed a member out of the ArubaOS-CX 6300 VSF configuration. The login to the removed member falls. What is true about switch login recovery?

The task requires physical access to the switch

The zeroize task executes the zeroize.txt from the root of the CF card on the switch

The zeroize task will remove all user passwords: the configuration remains on the switch

The task can be executed remotely

HP HPE6-A69 Practice Test 1 - Free Online Exam Prep & Questions

Question 1 / 40

Refer to the exhibit.

HP HPE6-A69 image Question 1 14251 09162024180637000000

Aruba CX 6300 switch has routes in three different VRFs as per the example above. The user needs to leak routes between VRF Secure and VRF Dev. and also between VRF default and VRF Dev The customer Is not able to establish routing between directly connected networks 10.100.50.0/24 and 10.102.26.0/24 Which statement is true regarding the routing troubleshooting?

Multi-protocol BGP routing needs to be defined for route leaking

Route Distinguisher needs to be set to 1 for default VRF.

Route leaking is supported between non-default VRFs only

Route leaking between default and non-default VRFs is supported with Aruba CX 8400.

Comment (0)

HP HPE6-A69 Practice Test 1

Question

HP HPE6-A69 Practice Tests

Practice Tests