What is correct regarding the configuration of ACLs on AOS-CX switches?

Wildcard masks are used to match on a range of IP addresses.

Statements with the log keyword are always processed by the switch CPU.

Standard ACLs are used to match on routes when performing route distribution.

Wildcard masks are used to match on a range of IP addresses.

Numbers 100 through 199 and 2000 through 2999 are used when creating extended ACLs.

Examine the network exhibit. A network administrator is implementing OSPF on a VSX pair of aggregation switches: Agg1 and Agg2. VLANs 10 and 20 are connected to layer-2 access switches. Agg-1 and Agg-2 are configured as the default gateway for VLANs 10 and 20, with active gateway enabled.What is the best practice for configuring OSPF on the aggregation switches and their connection to the Core switch?

Define a layer-2 VSX LAG associated with a layer-3 VLAN interface. Enable active gateway for the Layer-3 VLAN.

Define separate layer-3 VLAN interfaces between the aggregation and core switches. Enable active forwarding for the Layer-3 VLAN.

Define separate layer-3 VLAN interfaces between the aggregation and core switches. Enable active gateway for the Layer-3 VLAN.

Define a layer-2 VSX LAG associated with a layer-3 VLAN interface. Enable active forwarding for the Layer-3 VLAN.

When implementing deficit weighted round robin queuing, what importance does the weight value have?

Queue priority in processing traffic

Prioritizing latency-sensitive traffic

Queue priority in processing traffic

Percentage of interface bandwidth

A network administrator is implementing OSPF, where there are two exit points. Each exit point has a stateful, application inspection firewall to implement company policies.What would the best practice be to ensure that one firewall will see both directions of the traffic, preventing asynchronous connections in the network?

Both ASBRs should define External Type 1 routes for the

Both ASBRs should define External Type 2 routes for the

What is a concept associated with PIM sparse mode (SM)?

Requires periodic joins to maintain the shortest path tree (SPT).

Reverts to forwarding when the pruning state times out.

Requires periodic joins to maintain the shortest path tree (SPT).

Recommended for use when high bandwidth connections exist.

Implements a push content to forward traffic from the multicast source.

Examine the following AOS-CX switch configuration: Which access control entries would allow web traffic to the web servers 10.1.0.100 and 10.1.1.100?

permit tcp any 10.1.0.100 0.0.1.0 eq 80

permit tcp any 10.1.0.100/10.1.1.100 eq 80

permit tcp any 10.1.0.100/255.255.254.255 eq 80

What is a best practice concerning voice traffic and dynamic segmentation on AOS-CX switches?

Controller authentication and port-based tunneling of the voice traffic

Controller authentication and user-based tunneling of the voice traffic

Switch authentication and user-based tunneling of the voice traffic

Controller authentication and port-based tunneling of the voice traffic

Switch authentication and local forwarding of the voice traffic

What is required when implementing captive portal an AOS-CX switches?

Certificate installed on the switch

Web server running on the switch

The AOS-CX mobile app allows a network engineer or technician to perform which tasks? (Choose two.)

Create a stack of AOS-CX switches.

Transfer files between the switch and your mobile device.

Use NetEdit to manage switch configuration.

Create a stack of AOS-CX switches.

Transfer files between the switch and your mobile device.

Securely access the switch using SSH.

Schedule an operating system upgrade.

An administrator implements interim accounting for guest users so that ClearPass can track the amount of bandwidth that guests upload and download. Guests that abuse bandwidth consumption should be disconnected from the network.The administrator configures the following on the AOS-CX access switches: After performing this configuration, the administrator notices that guest users that have exceeded the guest bandwidth limit are not being disconnected. Upon further investigation, Access Tracker in ClearPass indicates a disconnect CoA message is being sent to the AOS-CX switch.What is causing this issue?

RADIUS change of authorization is not enabled on the AOS-CX switch.

Bandwidth consumption of the guests is not being reported by the AOS-CX switch.

NTP is not configured on the AOS-CX switch.

There is a time discrepancy between the AOS-CX switch and ClearPass.

A company has a few servers in a secure, remote location storing highly-confidential documents connected to two AOS-CX 6400 switches configured in a VSX pair The AOS-CX switches perform access control with 802 1X and will be implementing user-based tunneling (UBT) so that Aruba gateway application inspection and stateful firewall policies can be applied to the traffic. The gateways are running version 84 and implement the AP, PEF, and RFP licenses Which licensing is needed for the two AOS-CX switches?

1 AP, 1 PEF, and 1 RFP licenses only

2 AP, 2 PEF, and 2 RFP licenses only

1 AP, 1 PEF, and 1 RFP licenses only

A customer has twenty AOS-CX switches that will be managed by NetEdit and would like support for NetEdit these switches will exist in the network for at least five years.Which type of licensing should be used by this customer?

20 Aruba NetEdit single node subscription licenses

20 Aruba NetEdit permanent licenses

20 Aruba NetEdit single node subscription licenses

25 Aruba NetEdit permanent licenses

An administrator is implementing a multi-area OSPF network. The network contains a backbone (area 0) and two other areas (1 and 2) connected to ABRs in the backbone The network has one routing switch connected to a service provider located in area 2 Which network design would minimize the number of routes in the routing switches' link state databases (LSDBs) while still allowing full connectivity?

Area 0: Not-so-stubbyArea 1: Totally not-so-stubby Area 2: Totally not-so-stubby

Area 0: NormalArea 1: Totally stubby Area 2: Totally stubby

Area 0: NormalArea 1: Totally not-so-stubby Area 2: Totally stubby

Area 0: NormalArea 1: Totally stubbyArea 2: Totally not-so-stubby

Area 0: Not-so-stubbyArea 1: Totally not-so-stubby Area 2: Totally not-so-stubby

An administrator will be deploying NetEdit to manage an Aruba solution. What does NetEdit support?

Manages AOS-CX switches and Aruba gateways

Support for Aruba-supplied security updates

Tracks configuration and hardware information

Can be purchased as a VM and/or hardware appliance

Examine the AOS-CX configuration: The switches have a default factory password setting NetEdit fails to access the configuration of the AOS-CX switches. What should the administrator do to solve this problem?

Set a password for the default admin user account.

Use the default VRF instead of the mgmt VRF

A network engineer is setting up BGP on AOS-CX switches. The engineer is establishing two different eBGP peering's to two different service providers. The engineer has dozens of contiguous C-class public networks that need to be advertised to the two service providers. The engineer manually defines the networks to be advertised individually with the "network" command.How can an administrator advertise only a summarized route to the two service providers?

Summarize the networks with the "aggregate-address" BGP command

Create a summarized static route and redistribute this into OSPR

Summarize the networks with the "aggregate-address" BGP command

Enable auto-summarization in the IPv4 address family of the BGP configuration

Create a summarized route in OSPF

What is the purpose of the transit VLAN when implementing dynamic segmentation policies involving AOS-CX switches and an Aruba gateway solution?

It identifies the VLAN that the switch will use when tunneling the traffic to the gateway

It identifies the VLAN that the user traffic will be assigned to when it comes out of the tunnel and is forwarded by the gateway.

It identifies the VLAN that the user traffic will be assigned to, whether the traffic is tunneled or locally switched

It defines the VXLAN identifier to identified UBT traffic between the AOS-CX switches and the gateway solution

It identifies the VLAN that the switch will use when tunneling the traffic to the gateway

An administrator is managing a VSX pair of AOS-CX switches An administrator configures the following on the primary AOS-CX switch:

The VLAN is created on both the primary and secondary switches

The primary switch will erase VLAN 200 from the VSX pair

The VLAN is only created on the secondary switch.

The operation is not allowed by the switch and a CLI error is displayed

The VLAN is created on both the primary and secondary switches

What is true regarding VSX and keepalives on AOS-CX switches?

A separate VLAN on the ISL link is used.

A VSX LAG for the keepalives is a best practice.

MAC authentication is enabled on port 1/1/27 of an AOS-CX switch. The following MAC addresses are defined on the AAA server:* 88:3a:30:97:b6:00* 00:50:56:b1:fc:9bExamine the AOS-CX switch output: Based on this information, what is true concerning port 1/1/27?

Client-mode is enabled with a client limit of 1.

Device-mode is enabled with a client limit of 1.

Device-mode is enabled with a client limit of 2.

Client-mode is enabled with a client limit of 1.

Client-mode is enabled with a client limit of 2.

A network administrator is tasked to set up BGP in the company's network. The administrator is defining an eBGP peering between an AOS-CX switch and a directly-connected service provider. The administrator has configured the following on the AOS-CX switch: However, when using the "show bgp all summary" command, the state does not display "Established" for the eBGP peer. What must the administrator configure to fix this issue?

router bgp 64500 address-family ipv4 unicast neighbor 192.168.1.1 activate

router bgp 64500 neighbor 192.168.1.1 ebgp-multihop

router bgp 64500 address-family ipv4 unicast neighbor 192.168.1.1 activate

router bgp 64500 neighbor 192.168.1.1 update-source loopback0

HP HPE6-A73 Practice Test 3 - Free Online Exam Prep & Questions

Question 1 / 40

Examine the network topology.

HP HPE6-A73 image Question 81 14650 09162024180712000000

The network is configured for OSPF with the following attributes:

Core1 and Core2 and ABRs

Area 1 has 20 networks in the 10.1.0.0/16 range

Area 0 has 10 networks in the 10.0.0.0/16 range

Area 2 has 50 networks in the 10.2.0.0/16 range

The ASBR is importing a static route into Area 1

Core2 has a summary for Area 2: area 0.0.0.2 range 10.2.0.0/16 type inter-area

Here is the OSPF configuration performed on Core1:

HP HPE6-A73 image Question 81 14650 09162024180712000000

Based on the above information, what is correct?

Become a Premium Member for full access

Unlock Premium Member

HP HPE6-A73 Practice Test 3

Question

HP HPE6-A73 Practice Tests

Practice Tests