Home / HP / HPE7-A04

HP HPE7-A04 Practice Test - Questions Answers, Page 10

Question list

List of questions

Question 91

(0)

Two VMs on the same ESXi host are assigned to an isolated VLAN 2001 (primary VLAN 1001). The host connects to an HPE Aruba CX 10000 switch on an access port. The switch supports the same PVLAN setti

Question 92

(0)

What is true about the assumption documents?

Question 93

(0)

You are adding EVPN VXLAN to an L3 spine and leaf topology that uses OSPF for the underlay. You plan to use a single BGP AS. Which design for EVPN neighbors is correct?

Question 94

(0)

In Routing design for a two-tier topology between the data center and other parts of the network, select the best option from below:

Question 95

(0)

You want to implement distributed firewall policies that micro-segment VM-to-VM traffic, including within the VLAN and same host. The VMs should be able to send traffic on permitted TCP ports, but o

Question 96

(0)

Which of the following are deemed as Post-installation handover tasks?

Question 97

(0)

You are setting up a single EVPN VXLAN fabric for a data center. A customer has one ESXi cluster in racks 1-3 that uses VLAN 10 for VMs in subnet 10.1.10.0/24. The customer has another ESXi cluster

Question 98

(0)

2-Tier L2 Design * 6400 100G Core Switches * 8320 48-P 10G RJ45 Access Switches * 40G DAC connections between Core and Access Core Switches = VSX Pairs of 6400 switches (each with 2 x 12-port QS

Related questions

What resiliency technologies relate to Default Gateway redundancy requirement on CX switches?

What is true about rollback plan for migration phases? (Select two)

Which of these protocols carries commands for reading from/writing to storage over a TCP/IP session?

In a multi-AS underlay design:

What materials do you need to include for the solution proposal? (Choose all that apply)

You are involved in a 2-Tier L2 Data Center Design with the following details: * CX 8325 100G Core Switches * CX 10000 48-P 25G Access Switches * 100G SR4 Optical connections between Core and Access In this design, both the Core Layer and Access Layer consist of pairs of switches configured in VSX for HA. Core Switches = VSX Pairs of CX 8325 32-port 100G switches (B-F airflow) Each pair uses: * 2 x 100G QSFP28 1M DACs for ISL * 1 x 100G QSFP28 1M DAC for Keepalive * 2 x 100G QSFP28 SR4 Optic to each access switch Each Core switch has 13 available 100G QSFP28 interfaces. What is the maximum number of racks supported by this design?

What is the maximum distance supported by Active Optical Cables (AOC)?

Choose the most suitable technology for the DCI (Data Center Interconnect) when Data Centers are geographically not in the same building:

In L3 Spine and Leaf design, which answer is correct?

Two VMs on the same ESXi host are assigned to an isolated VLAN 2001 (primary VLAN 1001). The host connects to an HPE Aruba CX 10000 switch on an access port. The switch supports the same PVLAN settings. VM 1 sends traffic to VM 2. Which policy or policies does the switch apply (assuming that they exist)?

Question 91

Egress policy on VLAN 1001

No policies because the traffic remains local to the ESXi host

Ingress and egress policy on VLAN 1001

Ingress policy on VLAN 1001

Show Answer Comment (0)

Question 92

What is true about the assumption documents?

Must never be included in the solution proposal

Assumptions are so essentials that they need to always be included with every solution

Assumptions are only needed if the customer asks for it

Assumptions vary based on the project

Show Answer Comment (0)

Question 93

You are adding EVPN VXLAN to an L3 spine and leaf topology that uses OSPF for the underlay. You plan to use a single BGP AS. Which design for EVPN neighbors is correct?

Leaf switches should establish iBGP sessions with other leaf switches using their VXLAN loopback IPs. Route reflectors are not required

The border leaf switches should act as route reflectors and specify the leaf switches' VXLAN loopback IPs as route reflector clients

At least one spine switch should act as route reflector and specify the leaf switches' unique loopback IPs as route reflector clients

Leaf switches should establish iBGP sessions with spine switches on their actual P2P link IP addresses. Route reflectors are not required

Show Answer Comment (0)

Question 94

In Routing design for a two-tier topology between the data center and other parts of the network, select the best option from below:

You should not use VSX LAGs for these connections

Don't use Layer 3 links

Establish point-to-point links using individual /29 subnets

Set up each link as an L3 interface or routed-only port (ROP)

Show Answer Comment (0)

You want to implement distributed firewall policies that micro-segment VM-to-VM traffic, including within the VLAN and same host. The VMs should be able to send traffic on permitted TCP ports, but other traffic should be dropped (hosts are isolated). What are two requirements? (Select two.)

SVI 10 on the switch has IP local ARP proxy enabled on it

The VMware host is configured to implement a local firewall

VLAN 10 is converted to a PVLAN on the switch only. The VMs are placed in an isolated VLAN

VLAN 10 is converted to a PVLAN on the switch and VMware hosts. The VMs are placed in an isolated VLAN

Show Answer Comment (0)

Question 96

Which of the following are deemed as Post-installation handover tasks?

Project budget details

Enable monitoring of new systems

RFP

Show Answer Comment (0)

Question 97

You are setting up a single EVPN VXLAN fabric for a data center. A customer has one ESXi cluster in racks 1-3 that uses VLAN 10 for VMs in subnet 10.1.10.0/24. The customer has another ESXi cluster in racks 4-6 that uses VLAN 10 for VMs in subnet 10.2.10.0/24. Which is correct?

You can map VLAN 10 to different VNIs on the same switches if you place VLAN 10 in multiple VRFs

You must tell the customer to change the VLAN ID in racks 4-6 to a unique ID

You can use subnets rather than VLANs for VNI mappings so you can use the same configuration everywhere

You can map VLAN 10 to one VNI on switches in racks 1-3 and to a different VNI on switches in racks 4-6

Show Answer Comment (0)