Exhibit Which two statements are correct about the information shown in the exhibit? (Choose two.)

The root bridge is reachable using the ge-0/0/14 interface.

This switch has a bridge priority of 8k.

The root bridge is reachable using the ge-0/0/14 interface.

This switch is the root bridge for this spanning tree topology.

This switch has a bridge priority of 8k.

The root bridge's priority Is 4k.

Exhibit You are advertising a summary route that represents your local network (172.20.0.0716) to both ISP A and ISPB. You want to influence all traffic sent to you from ISP C to go through R2.How would you accomplish this task?

On R1, change the local preference value to 250.

On R1, prepend your AS number three times on the 172.20.0.0/16 route when advertising It to ISP 1.

On R1, change the local preference value to 250.

On R2. prepend your AS number three times on the 172.20.0.0/16 route when advertising it to ISP 2.

On R2, change the local preference value to 50.

Which two statements ate correct about the community BGP attribute on a Junos device? (Choose two.)

The community attribute is a mandatory BGP attribute.

If the community attribute is present, it should be passed unchanged in the BGP updates.

The community attribute is a mandatory BGP attribute.

If the community attribute is present, it is ignored and deleted in the BGP updates.

If the community attribute is present, it should be passed unchanged in the BGP updates.

The community attribute is an optional BGP attribute.

Exhibit Referring to the exhibit, how do you verify the status of the tunnel from R1?

Issue the ping 172.20.iii.io source 203.0.113.2 command.

Issue the ping 172.20.111.10 source 172.20.110.1 command.

Issue the ping 172.20.111.10 source 198.51.100.1 command.

Issue the ping 172.20.iii.io source 203.0.113.2 command.

Issue the ping 172.20. Ill. 10 command.

You are asked to configure an LSP which uses the OSPF link state database for path computations. Which two statements are correct in this scenario? (Choose two.)

You must use the no-cspf parameter in the label-switched-path configuration.

Traffic engineering extensions are not enabled by default in OSPF.

You must use the no-cspf parameter in the label-switched-path configuration.

Traffic engineering extensions ate enabled by default In OSPF.

Traffic engineering extensions are not enabled by default in OSPF.

You must use the policing parameter in the label-switched-path configuration.

The segment touting SRGB start label Is 10,000 and the SRGB index range is 500.In this scenario, which two statements are correct? (Choose two.)

The last usable label is 10,499.

The first usable label Is 10,000.

The first usable label is 10,001.

The last usable label is 10.501.

The last usable label is 10,499.

The first usable label Is 10,000.

Exhibit You configured interface ge-0/070.0 to run IS-IS. but this interface does not appear in the output of the show isis adjacency command as shown in the exhibit.What is the problem in this scenario?

The family iso statement must be added to the logical interface.

This is a Gigabit Ethernet interface, that is incompatible with the reference-bandwidth 100g statement.

The family iso statement must be added to the logical interface.

The router at the other end of the link Is not sending any IS-IS Hello messages.

The router at the other end of the link is a Level 1 only router.

An OSPF router does not have a router ID configured.In this scenario, which statement is correct about the router ID?

The Junos OS will use the IP address assigned to the loopback interface for the router ID.

The Junos OS will use the IP address assigned to the interface with the lowest MAC address.

A router ID will not be assigned until it is manually configured.

The Junos OS will use the IP address assigned to the loopback interface for the router ID.

The Junos OS will use the IP address assigned to the Interface with the highest priority.

You want to see a detailed list of all established BGP sessions. In this scenario, what would be a valid command to accomplish this task?

show rouse receive-protocol bgp <neighbor IP address>

What is the correct order of BGP attributes for active route selection?

next hop -> local preference -> AS path -> origin -> MED

next hop -> local preference -> AS path -> MED -> origin

next hop -> AS path -> local preference -> origin -> MED

next hop -> local preference -> AS path -> origin -> MED

next hop -> origin -> local preference -> AS path -> MED

Exhibit Referring to the exhibit, where should next-hop-self-policy be applied to alter the next-hop value?

The policy is applied as an export policy for the group int-64503.

The policy is applied as an export policy for the group ext-64501.

The policy is applied as an import policy for the group int- 64 503.

The policy is applied as an Import policy for the group ext-64501.

Exhibit Referring to the exhibit, which two statements are correct? (Choose two.)

Prefixes in Level 1 will be redistributed to Level 2.

Prefixes in Level 2 will be not redistributed to Level 1.

Prefixes in Level 1 will be redistributed to Level 2.

Prefixes in Level 2 will be not redistributed to Level 1.

Prefixes in Level 1 will not be redistributed to Level 2.

Prefixes in Level 2 will be redistributed to Level 1.

Exhibit button Which two statements are correct about the service provider MPLS network shown in the exhibit? (Choose two.)

R3 will perform a label pop operation on the transport MPLS label.

R3 will perform a label swap operation on the transport MPLS label.

R3 will perform a label pop operation on the transport MPLS label.

Traffic from Network 1 to Network 3 and traffic from Network 1 to Network 4 each need their own unique label-switched path.

Traffic from Network 1 to Network 3 and from Network 1 to Network 4 can share the same label-switched path.

R3 will perform a label swap operation on the transport MPLS label.

Which two statements are correct about IS-IS? (Choose two.)

A level 1 only router can never form an adjacency with a level 2 only router.

For level 2 adjacencies, the area IDs can be different.

A level 1 only router can never form an adjacency with a level 2 only router.

For level 2 adjacencies, the area IDs can be different.

For level 2 adjacencies, the area IDs must be the same.

A level 1 only router can form an adjacency with a level 2 only router.

You are adding an IPv6 configuration to an Interface on a Junos device.In this scenario, which statement is correct?

The link local address is automatically created using the MAC address within the fd00::/8 prefix range.

The link local address must be manually configured within the fdO0::/8 prefix range.

The link local address must be manually configured within the fe80::/10 prefix range.

The link local address is automatically created using the MAC address within the fe80::'l0 prefix range.

The link local address is automatically created using the MAC address within the fd00::/8 prefix range.

Which statement is correct about IS-IS?

IS-IS is a link-state routing protocol.

IS-IS is a distance vector routing protocol.

IS-IS is a path vector routing protocol.

IS-IS is a link-state routing protocol.

IS-IS is a classful routing protocol.

Interface ge-0/0/0.0 connecls yout network to your ISP. You want to advertise this interface address as an Internal route In OSPF without creating a neighbor with your ISP.In this scenario, how is this task accomplished?

Configure a static route for Interface ge-0/0/0.0.

Remove interface ge-0/0/0.0 from OSPF.

Create a generated route for Interface ge-0/0/0.0.

Add ge-0/0/0.0 as a passive interface In OSPF.

Configure a static route for Interface ge-0/0/0.0.

Which statement describes integrated routing and bridging (IRB) interfaces?

An IRB interface enables Layer 2 switching on the router.

An IRB interface Is an IP gateway For hosts of a bridge domain.

An IRB interface assigns interfaces to VLANs.

An IRB interface enables Layer 2 switching on the router.

An IRB interface defines a bridge domain.

Exhibit The LSP is not establishing correctly.Referring to the exhibit, what should you do to solve the problem?

Enable traffic engineering for the RSVP protocol.

Enable traffic engineering for the OSPF protocol.

Enable traffic engineering for the IS-IS protocol.

Enable traffic engineering for the BGP protocol.

Enable traffic engineering for the RSVP protocol.

You are bringing a new network online with three MX Series devices enabled for STP. No root bridge priority has been configured. Which statement is true in this scenario?

The device with the lowest MAC address will be elected as the root bridge.

The device with the highest MAC address will be elected as the root bridge.

The device with the lowest numerical lo0 IP address will be elected as the root bridge.

The device with the highest numerical lo0 IP address will be elected as The bridge.

What Is a key differentiator of generate routes from aggregate routes?

Generate routes use a forwarding next hop.

Generate routes have a default next-hop value of reject.

Generate routes have a default preference value of 210.

Generate routes cannot be used as a gateway of last resort.

Which statement is correct about the FE80;:/10 prefix?

This prefix range is used for the link local address.

This prefix range is used on the loopback interface.

This prefix range is reserved for multicast applications

This prefix range is not reserved.

You are deploying link aggregation groups.

There should only be four member links per LAG.

Member links are required to be contiguous ports.

By default, what are two considerations in this scenario? (Choose two.)

There should only be four member links per LAG.

All the ports must have the same speed.

Member links are required to be contiguous ports.

Member links can reside on different members within an MC-LAG.

Exhibit You are asked to assign interface xe-1/0/5 to a virtual switch.What must be accomplished to complete the configuration?

Interface xe-1/0/5 must be added to routing-instance sw-1.

Interface xe-1/0/5 must be added to routing-instance sw-1 vlan_2.

Interface xe-1/0'5 must be a trunk port.

Interface xe-1/0/5 must be added to routing-instance sw-1.

An IRB interface must be configured to routing-instance sw-1 vlan_2.

Exhibit Referring to the exhibit, which statement is true about VRRP?

The routers should use different virtual IP addresses for VRRP to function correctly.

VRRP communication between the two devices is not functioning correctly.

Both routers are in the same state because they have the same VRRP priority.

RRP Is functioning normally in active/active mode.

The routers should use different virtual IP addresses for VRRP to function correctly.

Exhibit. Referring to the exhibit, you have configured an aggregate route that represents the 172.21.0.0/24, 172.21.1.0/24, and 172.21.2.0/24 networks. However, when you view the routing table, your new route hidden.Which action would you perform to determine the problem?

Verify that you have set the preference to a lower default value.

Verify that you have active contributing routes on the device.

Verify that you have configured a policy on the device to accept aggregate routes.

Verify that you have defined a metric value for the aggregate route.

Verify that you have set the preference to a lower default value.

Exhibit You are asked to configure the OSPF environment to prevent the DRother routers from participating in DR/BDR election.Referring to the exhibit, which command will accomplish this task?

set protocols ospf area 0.0.0.0 interface ge-0/0/l priority 255

set protocols ospf area 0.0.0.0 interface ge-0/0/1 priority 0

set protocols ospf area 0.0.0.0 interface ge-0/0/1 interface-type nbma

set protocols ospf area 0.0.0.0 interface ge---0/0/1 interface-type p2p

Exhibit Which two statements ate correct about the actions taken as the packet traverses the service provider MPLS network from Site 1 to Site 2 as shown in the exhibit? (Choose two.)

R2 will perform a lookup using the mpls.0 table.

R1 will perform a lookup using the lnet.3 table.

R1 will perform a lookup using the mpls.0 table.

R2 will perform a lookup using the inet.3 table.

ExhibitS ExhibitLSI1 A AS 65501ISPB AS 65502Advertised Prefixes: 172.20.0.0/24 172.20.20.0/24 172.20.21.0/24\ NAdvertised Prefixes: 172.20.0.0/24172.20.1.0/24 Referring to the exhibit, which two statements are correct? (Choose two.)

Devices in AS 65512 will prefer ISP B for traffic destined to the 172.20.21.0/24 network.

Devices in AS 65512 will prefer ISP A for traffic destined to the 172.20.21.0/24 network.

Devices In AS 65512 will prefer ISP A for traffic destined to the 172.20.0.0/24 network.

Devices in AS 65512 will prefer ISP B for traffic destined to the 172.20.21.0/24 network.

Devices In AS 65512 will prefer ISP B for traffic destined to the 172.20.0.0/24 network.

Exhibit You have an established LSP between your R1 and R5 devices using the configuration shown in the exhibit. You are asked to ensure that MPLS labels are used to forward traffic by all devices within the LSP.Which action will accomplish this behavior?

Configure the install statement under the R1_TO_R5 label switched path on R1.

Configure the ultimace-hop-popping statement under the R1_TO_R5 label switched path on R1.

Configure the explicit-null statement under the protocol mpls hierarchy on R1.

Delete the no-espf statement under the R1_TO_R5 label switched path on R1.

Configure the install statement under the R1_TO_R5 label switched path on R1.

Exhibit You are asked to configure OSPF between routers R1 and R2 using IPv6 addresses.Which two tasks will accomplish your objective? (Choose two.)

Under the [edit routing-options] hierarchy, configure a 32-bit router ID.

issue the set protocols ospf3 area 0.0.0.0 interface ge-0/0/1.0 command.

Issue the sec protocols ospf area 0.0.0.0 interface ge-0/0/1.0 command.

Under the [edit routing-options] hierarchy, configure a 32-bit router ID.

issue the set protocols ospf3 area 0.0.0.0 interface ge-0/0/1.0 command.

Under the [edit routing-options] hierarchy, configure a 128-bit router ID.

Juniper JN0-363 Practice Test 1 - Free Online Exam Prep & Questions

You are asked to create connections between routing instances on the same Junos device and route between the connected Instances. What are two ways to accomplish this task? (Choose two.)

Use physical interfaces.

Use an IRB interface.

Use logical tunnel interfaces.

Use loopback interfaces.

Comment (0)

Juniper JN0-363 Practice Test 1

Question

Juniper JN0-363 Practice Tests

Practice Tests