Exhibit Which two statements are correct about the service provider MPLS network shown in the exhibit? (Choose two.)

R3 is considered a transit router.

R3 is considered an ingress router.

You have created a routing instance named vr3 that will provide access to Server 2 (10.0.0.2) (or the hosts on the 10.10.10.0/24 network. Which command would you use to test connectivity between vr3 and Server 2?

user9router1> ping 10.0.0.2 count 5

user@vr3> ping 10.0.0.2 count 5

user@vr3> ping 10.0.0.2 count 5 source 10.10.10.1

user9router1> ping 10.0.0.2 count 5

user@router1> ping 10.0.0.2 routing-instance vr3 count 5

Exhibit Referring to the exhibit, what will happen to untagged frames?

The untagged frames are dropped.

The untagged frames are load balanced between VLAN 10 and VLAN 20.

The untagged frames are associated with VLAN 10.

The untagged frames are associated with VLAN 20.

Exhibit Referring to the exhibit, internal BGP between R1 and R2 is not establishing.What is the problem In this scenario?

R1 does not have a route to 192.168.200.2.

R1 and R2 must each have unique AS numbers.

R1 needs to be configured with an explicit router ID.

R1 needs to be configured with a next-hop self policy.

Exhibit Referring to the exhibit, which two additional steps should you lake to fully configure NSR? (Choose two.)

You should configure commit synchronization.

You should configure the max period for NSR precision timers.

You must configure graceful restart.

You should configure commit synchronization.

Exhibit You have configured graceful RE switchover (GRES), however you cannot complete the show system switchover command.Referring to the exhibit, what is the problem?

The command is only available on the backup Routing Engine.

The command is only available if non-stop routing is enabled.

The command is only available on the backup Routing Engine.

The command is only available If a backup router is configured.

The command is only available If graceful restart is enabled.

Which two statements are correct about the way that BGP propagates routes by default? (Choose two.)

A route learned by EBGP will be re-advertised to IBGP peers.

A route learned by IBGP will not be re-advertised lo IBGP peers.

A route learned by EBGP will be re-advertised to IBGP peers.

A route learned by IBGP will not be re-advertised lo IBGP peers.

A route learned by EBGP will not be re-advertised to IBGP peers.

A route learned by IBGP will be re-advertised to IBGP peers.

Which two statements are correct when using LDP? (Choose two.)

The inet.3 table will contain a full mesh of label-switched paths to other LDP-enabled routers.

LDP label-switched paths are created by configuring LDP on the loopbacK Interface.

The lnet.3 table will contain only the paths explicitly defined.

The inet.3 table will contain a full mesh of label-switched paths to other LDP-enabled routers.

LDP label-switched paths are created by configuring LDP on at least one physical router interface.

LDP label-switched paths are created by configuring LDP on the loopbacK Interface.

Exhibit Referring to the exhibit, which two statements are correct? (Choose two.)

Traffic ingressing ge-0/0/0 that is tagged with VLAN 101 will egress ge-0/0/1 unchanged.

Traffic ingressing ge-0/0/0 that is tagged will VLAN 100 will be dropped.

Traffic ingressing ge-0/0/0 that is tagged with VLAN 101 will egress ge-0/0/1 unchanged.

Traffic ingressing ge-0/0/0 that is tagged will VLAN 100 will be dropped.

Traffic ingressing ge0/0/0 that Is tagged with VLAN 200 will egress ge-0/0/1 with an outer VLAN tag of 200.

Traffic ingressing ge-0/0/0 that is tagged with VLAN 101 will egress ge-0/0M with an outer VLAN tag of 200.

Exhibit You confirm that the R2 and R3 routers are receiving a BGP route to the 203.0.113.0/24 network, but both routers display the route as hidden. Referring to the exhibit, which two actions solve this problem? (Choose two.)

Configure a routing policy on R1 that sets the next hop for the 203 0.113.0/24 BGP route to the IP address that R1 uses for IBGP peering.

Apply the routing policy on R1 as an export policy to the IBGP group.

Apply the routing policy on R1 as an import policy to the IBGP group.

Configure a routing policy on R1 that sets the next hop for the 203 0.113.0/24 BGP route to the IP address that R1 uses for IBGP peering.

Configure a routing policy on R1 that sets the next hop for the 203.0.113.0/24 BGP route to the IP address that R1 uses for EBGP peering.

Apply the routing policy on R1 as an export policy to the IBGP group.

Apply the routing policy on R1 as an export policy to the IBGP group. = export that to ur iBGP peers

Exhibit Referring to the exhibit, which two statements are correct? (Choose two.)

Junos OS default OSPF hello timers and dead intervals are used on all interfaces.

The OSPF Interfaces are configured as point-to-point.

The ge-0/0'1.0 Interface is configured as passive.

Junos OS default OSPF hello timers and dead intervals are used on all interfaces.

How does a Junos device learn about MAC addresses when II is first connected to an Ethernet LAN?

The device sends out a network multicast message asking for all devices and MAC addresses on the network and stores this Information in addition to the interface from which the response was received.

The device sends out a network broadcast message asking tor all devices and MAC addresses on the network and stores this information In addition lo the interface from which the response was received.

The device learns the destination MAC addresses from traffic in the network and stores this MAC address in addition to the interface from which the traffic was received.

The device learns the source MAC addresses from traffic in the network and stores this MAC address in addition to the interface from which the traffic was received.

The device sends out a network multicast message asking for all devices and MAC addresses on the network and stores this Information in addition to the interface from which the response was received.

When would you use the qualified-next-hop statement with a static route?

You can use it to specify multiple next hops with different preferences.

You can use it to install the static route into different routing tables.

You can use it to send unwanted traffic to a null route.

You can use it to specify multiple next hops with different preferences.

You can use it to resolve the next hop if the next hop is not directly connected.

Click the Exhibit button. Referring to the exhibit, you have an established RSVP LSP between R1 and R4 when you experience a link failure between R2 and R3.Which two statements are correct? (Choose two.)

R2 sends a ResvTear message upstream to R1 signaling the link failure.

R3 sends a PathTear message downstream to R4 signaling the link failure.

R2 sends a ResvTear message upstream to R1 signaling the link failure.

R3 sends a PathTear message downstream to R4 signaling the link failure.

R2 sends a PathTear message upstream to R1 signaling the link failure.

R3 sends a ResvTear message downstream to R4 signaling the link failure.

Click the Exhibit button. All devices in the network are configured correctly and the path requirements are valid.Referring to the exhibit, which two statements are correct? (Choose two.)

The primary LSP will be signaled, and its state will be up.

The secondary LSP will not be signaled, and its state will be down.

The primary LSP will be signaled, and its state will be up.

The secondary LSP will not be signaled, and its state will be down.

The secondary LSP will be signaled, and its state will be up.

The primary LSP will not be signaled, and its state will be down.

By default, which two statements are correct about switch ports on a Junos device? (Choose two.)

Trunk ports receive and transmit tagged traffic.

Access ports receive and transmit untagged traffic.

Trunk ports receive and transmit untagged traffic.

Access ports receive and transmit tagged traffic.

Trunk ports receive and transmit tagged traffic.

Access ports receive and transmit untagged traffic.

You are troubleshooting two OSPF routers that have an adjacency that remains in the ExStart state.What would cause this problem?

mismatched MTU settings on the OSPF interfaces

mismatched OSPF hello intervals on the OSPF interfaces

mismatched authentication settings on the OSPF interfaces

mismatched MTU settings on the OSPF interfaces

mismatched subnet settings on the OSPF interfaces

Which two statements ate correct about the BGP next-hop attribute value? (Choose two.)

By default, the next-hop value is changed across EBGP links.

By default, the next-hop value is not changed across IBGP links.

By default, the next-hop value is changed across IBGP links.

By default, the next-hop value is changed across EBGP links.

By default, the next-hop value is not changed across IBGP links.

By default, the next-hop value is not changed across EBGP links.

Exhibit Referring to the exhibit, what must be included in the Route1 configuration when establishing an EBGP session with the ISP?

A local address must be specified.

The BGP session type internal must be specified.

The BGP session type external must be specified.

You want to share routes between two routing instances that you have configured?What are two ways to accomplish this task? (Choose two.)

Configure an instance import policy

Which two statements are correct about the behavior of IS-IS metrics? (Choose two.)

Wide metrics enable interfaces to advertise metrics larger than 63.

By default, all physical interfaces have a metric of 10.

Wide metrics enable interfaces to advertise metrics larger than 63.

By default, the metric of an interface is calculated based on the speed of the interface.

Wide metrics enable an interface to advertise different metrics at Level 1 and Level 2.

By default, all physical interfaces have a metric of 10.

Click the Exhibit button. Referring to the exhibit, from which device(s) does R3 learn about Route X?

directly from the router in AS 64502

You are bringing a new network online with three IS-IS routers using default Junos election priorities. The routers are configured as Level 2 only IS-IS routers. Which statement is true about the DIS election in this scenario?

The router with the highest MAC address will be elected as the DIS.

The router with the highest numerical lo0 IP address will be elected as the DIS.

The router with the lowest numerical lo0 IP address will be elected as the DIS.

The router with the lowest MAC address will be elected as the DIS.

You are asked to configure filter-based forwarding on a Junos device.Which two statements are correct in this scenario? (Choose two.)

You must create and apply a match filter.

You must create a routing instance.

You must create a routing policy.

You must create a route target.

You must create and apply a match filter.

You must create a routing instance.

Juniper JN0-363 Practice Test 2 - Free Online Exam Prep & Questions

You want to enable a routing platform with redundant REs to switch from a primary RE to a backup RE without alerting peer nodes. Which two technologies would you use to satisfy this requirement? (Choose two.)

GRES

VRRP

NSR

ISSU

Comment (0)

Juniper JN0-363 Practice Test 2

Question

Juniper JN0-363 Practice Tests

Practice Tests