Refer to the exhibit. Click the Exhibit button.Referring to the exhibit, which two statements are correct about BGP routes on R3 that are advertised to R1? (Choose two.)

By default, the BGP local-preference value that is assigned on R3 is advertised to R1.

By default, the next-hop value for these routes is not changed by R3 before being sent to R1.

By default, the next-hop value for these routes is changed by R3 before being sent to R1.

By default, all BGP attributes values must be removed before advertising the routes to R1.

By default, the BGP local-preference value that is assigned on R3 is advertised to R1.

By default, the next-hop value for these routes is not changed by R3 before being sent to R1.

Refer to the exhibit. Click the Exhibit button.You are troubleshooting an issue for a customer site that uses 10.10.0.0/24 in AS 65224, but you see another AS in the AS path.Referring to the exhibit, what is the cause of the problem?

AS 65000 is pre-pending AS 65137 to route advertisements.

The local AS is receiving two equal cost routes to 10.10.0.0/24.

The local AS is in the process of withdrawing the route from AS 65137.

AS 65137 is advertising the 10.10.0.0/24 prefix.

Refer to the exhibit. Click the Exhibit button.After adding Customer C to your Layer 3 VPN, you must ensure that PE2 is receiving VPN routes for all customers attached to PE1, as shown in the exhibit.Which operational command displays this information?

show route table customer-c.inet.0

Refer to the exhibit. Click the Exhibit button.Referring to the exhibit, which two statements are correct regarding the output shown in the exhibit? (Choose two.)

The multicast group is an ASM group.

The multicast traffic is using the SPT.

The multicast group is an ASM group.

The multicast traffic is using the SPT.

The multicast group is an SSM group.

The multicast traffic is using the RPT.

Refer to the exhibit. Click the Exhibit button.Referring to the exhibit, the PE-to-CE protocol being used is OSPF for the L3VPN. Also, there is an OSPF neighborship between CE-1 and CE-2.Which statement is correct in this situation?

Hosts at Site-1 will reach hosts at Site-2 through the CE-1 and CE-2 link by default.

You must set a high metric on the CE-1 to CE-2 link for hosts at Site-1 to use the L3VPN to reach hosts at Site-2.

Hosts at Site-1 will reach hosts at Site-2 through the CE-1 and CE-2 link by default.

Hosts at Site-1 will reach hosts at Site-2 through the L3VPN by default.

You must set a high metric on the CE-1 to PE-1 link for hosts at Site-1 to use the CE-1 to CE-2 link to reach hosts at Site-2.

Refer to the exhibit. Click the Exhibit button.Referring to the exhibit, which two statements are true? (Choose two.)

This route is learned from the same AS number.

The multipath configuration is used for load balancing.

The multihop configuration is used for load balancing.

This route is learned from two different AS numbers.

This route is learned from the same AS number.

The multipath configuration is used for load balancing.

Refer to the exhibit. Click the Exhibit hutton.You are configuring an interprovider Option C Layer 3 VPN to connect two customer sites.Referring to the exhibit, which three statements are correct? (Choose three.)

ASBR routers maintain the internal routes from its own AS and the loopback addresses from the other AS PEs.

PE routers maintain the internal routes from its own AS, the loopback address from the other AS PEs, and the L3VPN routes.

P routers only maintain the internal routes from their own AS.

ASBR routers maintain the internal routes from its own AS and the loopback addresses from the other AS PEs.

PE routers maintain the internal routes from its own AS, the loopback address from the other AS PEs, and the L3VPN routes.

P routers only maintain the internal routes from their own AS.

P routers maintain the internal routes from its own AS and the loopback address from the other AS PEs.

ASBR routers maintain the internal routes from its own AS, the loopback address from the other AS PEs, and the L3VPN routes.

You are configuring a Layer 3 VPN between two sites. You are configuring the vrf-target target : 65100:100 statement in your routing instance.In this scenario, which two statements describe the vrf-target configuration? (Choose two.)

This value is used to identify BGP routes learned from the remote PE device.

This value is used to add a target community to BGP routes advertised to the remote PE device.

This value is used to identify BGP routes learned from the local CE device.

This value is used to identify BGP routes learned from the remote PE device.

This value is used to add a target community to BGP routes advertised to the local CE device.

This value is used to add a target community to BGP routes advertised to the remote PE device.

Which two statements about IS-IS are correct? (Choose two.)

PSNPs are used to acknowledge a received LSP.

PSNPs are used to request a missing LSP.

PSNPs are used to acknowledge a received LSP.

CSNPs are used to acknowledge a received LSP.

CSNPs are used to request a missing LSP.

PSNPs are used to request a missing LSP.

Refer to the exhibit. Click the Exhibit button.PE-1 and PE-2 are configured with LDP-signaled pseudowires to provide connectivity between CE-1 and CE-2. You notice no connectivity exists between CE-1 and CE-2.Referring to the exhibit, which two statements describe potential causes for this fault? (Choose two.)

There is no LSP configured from PE-1 to PE-2.

Interface ge-0/0/0 on PE-1 is down.

There is no LSP configured from PE-2 to PE-1.

Juniper JN0-664 Practice Test 3 - Free Online Exam Prep & Questions

You have an L2VPN connecting two CEs across a provider network. The CEs and provider network are configured with the default MTU setting. You use the ping command from one

CE to the other CE with a size of 1500 bytes.

In this scenario, which statement is correct when using the ping command?

Become a Premium Member for full access

Unlock Premium Member

Juniper JN0-664 Practice Test 3

Question

Juniper JN0-664 Practice Tests

Practice Tests