Home / Nutanix / NCM-MCI

Nutanix NCM-MCI Practice Test - Questions Answers, Page 5

Question list

List of questions

Question 41

(0)

Refer to the exhibit. What is the purpose of eth2 on the CVMs?

Question 42

(0)

An administrator wants to utilize Network Visualization to monitor the physical and logical network on the Nutanix cluster. The first-hop switch has LLDP enabled. The network switch information is s

Question 43

(0)

An administrator is migrating 5MB shares from a third-party platform to Nutanix Files with the following characteristics: • Shares contain user profile directories • DFS-N will be used How should

Question 44

(0)

An administrator manages the following two Nutanix AOS 5.15 cluster environment: • Corp-cluster-01 • Corp-cluster-02 The VM images must be available only on Corp-cluster-01, but cannot be checked

Question 45

(0)

A customer has a Nutanix cluster with 10Gb connectivity via switch fabric extenders. The administrator receives NCC health check errors of latency greater than 200ms. Which action should the admini

Question 46

(0)

For several days, an administrator notices the following alerts: • CVM NIC Speed Low Warning Alerts • Warning Alerts of CVM NIC not performing at optimal speed • CVM is disconnected from the netw

Question 47

(0)

Refer to the exhibit. An administrator configures Active Directory authentication as shown in the exhibit. Upon finishing setup, users are not able to log in. What configuration change should be

Question 48

(0)

In a Nutanix cluster, a Protection Domain contains 50 entities that are replicated to a remote Single Node Replication Target. The current schedule configuration is as follows: • Repeat every 6 ho

Question 49

(0)

A customer with a four-node RF2 cluster is adding application VMs to their system. After adding these VMs, the Prism dashboard shows 81% storage utilization. What is the consequence of running the

Question 50

(0)

A company needs to replicate their VMs to a remote site and must have an RPO of less than 1 hour. When creating a protection domain, what should an administrator do to meet this requirement?

Question 41

Refer to the exhibit.

What is the purpose of eth2 on the CVMs?

RDMA Network Segmentation

iSCSI connectivity

Remote site connectivity

Network Segmentation

Show Answer Comment (0)

An administrator wants to utilize Network Visualization to monitor the physical and logical network on the Nutanix cluster. The first-hop switch has LLDP enabled. The network switch information is still not being displayed.

What is causing this problem?

The ISL between switches is not configured.

SNMP is not configured properly.

br0 and br1 are not defined.

The cluster is using RDMA-enabled NICs.

Show Answer Comment (0)

Question 43

An administrator is migrating 5MB shares from a third-party platform to Nutanix Files with the following characteristics:

• Shares contain user profile directories

• DFS-N will be used

How should the administrator create target shares for this migration?

Create multiple general purpose shares and distribute migrated data as evenly as possible.

Create multiple distributed shares and distribute migrated data as evenly as possible.

Create standard shares with multiple top-level directories and distribute migrated data.

Create distributed shares with multiple top-level directories and distribute migrated data.

Show Answer Comment (0)

Question 44

An administrator manages the following two Nutanix AOS 5.15 cluster environment:

• Corp-cluster-01

• Corp-cluster-02

The VM images must be available only on Corp-cluster-01, but cannot be checked out to cluster Corpcluster- 02. The images also cannot be checked out to any other clusters that are registered with Prism Central in the future.

Which two configuration settings must the administrator choose when creating the image placement policy that satisfies the stated requirements? (Choose two.)

Create an image placement policy that identifies cluster Corp-cluster-01 as the target cluster

Set the policy enforcement to Soft.

Set the policy enforcement to Hard.

Create an image placement policy that identifies cluster Corp-cluster-02 as the target cluster.

Show Answer Comment (0)

Question 45

A customer has a Nutanix cluster with 10Gb connectivity via switch fabric extenders. The administrator receives NCC health check errors of latency greater than 200ms.

Which action should the administrator take to resolve the NCC errors?

Replace the switch fabric extenders with 10G line rate switches

Upgrade NCC and increase the CVM memory by 4Gb

Add 2 additional 10G uplinks from the switch fabric extenders per node

Upgrade NCC and increase the vCPU of the CVM

Show Answer Comment (0)

Question 46

For several days, an administrator notices the following alerts:

• CVM NIC Speed Low Warning Alerts

• Warning Alerts of CVM NIC not performing at optimal speed

• CVM is disconnected from the network Critical Alert

• Network Visualization page shows excessive dropped packets on CVM/Host Which steps should be taken to determine which problem should be addressed first?

• Access the Hardware Page to verify resources are available• Analyze ail CVM Speed Alerts in the Alerts/Events page• Analyze output for the network and interface properties and connectivity issues

• Verify Host/CVM connectivity on the Network Visualization page• Use to verify the bridge and bond configuration• Review alerts/events page for the CVM disconnected error

• Review Alerts page for NIC speed alerts and alert timing• Analyze the genesis.out log file for process failures• Assess the NIC properties in the Network Visualization > Host Properties page

• Restart networking services on the CVM• Determine the current configuration of the affected CVM via output• Access the Alerts/Events page for the CVM network connection failures

Show Answer Comment (0)

Question 47

Refer to the exhibit.

An administrator configures Active Directory authentication as shown in the exhibit. Upon finishing setup, users are not able to log in.

What configuration change should be made to fix this issue?

Change leaps to https

Change the Directory URL to use an IP rather than a name

Change the plct from 389 to 636D Change the Domain to use an IP rather than a name

Show Answer Comment (0)

Question 48

In a Nutanix cluster, a Protection Domain contains 50 entities that are replicated to a remote Single Node Replication Target.

The current schedule configuration is as follows:

• Repeat every 6 hours

• Local Retention Policy 1

• Remote Retention Policy 8

• Starting time 12 am

At 8 am on Monday, the administrator discovers that a protected VM is corrupted. The latest good state was Sunday 2 pm. The administrator needs to maintain current protection.

Which strategy should the administrator use to meet these requirements?

From the Remote site, activate the Protection Domain, then re-protect the entity.

From the Remote site, restore the VM from the local snapshot by selecting the correct snapshot

From the local site, retrieve the correct remote snapshot, then restore the VM locally.

From the local site, restore the VM from the local snapshot by selecting the correct snapshot.

Show Answer Comment (0)

Question 49

A customer with a four-node RF2 cluster is adding application VMs to their system. After adding these VMs, the Prism dashboard shows 81% storage utilization.

What is the consequence of running the cluster at 81% storage utilization?

The customer has the ability to add more VMs up to the 100% storage utilization.

There is available capacity in the storage fabric and the cluster is resilient.

Node failure is imminent due to storage utilization.

The cluster is not resilient in the storage fabric

Show Answer Comment (0)