Ask Question
DELL D-RP-DY-A-24 Practice Test - Questions Answers, Page 4
List of questions
Question 31
Refer to the exhibit.
Based on the exhibit, what describes the state in which RPA-3 must be in prior to selecting 'Next' to advance the wizard?
Power On: Ensure that RPA-3 is powered on.
Configure LAN Address: Assign and configure the LAN IP address as displayed in the wizard for RPA-3.
Verification: Verify that the RPA-3 is reachable at the configured LAN address.
Advance the Wizard: Once the above steps are confirmed, select ''Next'' to proceed with the wizard.
Question 32
How does Unisphere identify a RecoverPoint initiator with VNX through RPA registration?
Initiator Identification: Unisphere identifies a RecoverPoint initiator with VNX through RPA registration by using the World Wide Name (WWN) of the RecoverPoint Appliance (RPA).
Registration Process: During the registration process, the RPA's WWN is used to uniquely identify and authenticate the RPA within the storage network.
Unisphere Integration: Once registered, the RPA can be managed and monitored through Unisphere, which is the management interface for VNX and other EMC storage systems.
For detailed procedures on RPA registration and integration with Unisphere, refer to the Dell RecoverPoint deployment documentation or the Unisphere for RecoverPoint user guide12.
Question 33
When the admin user password has been lost, how can the password be reset?
Access the CLI: Use the boxmgmt account to log into the Command Line Interface (CLI) of the RecoverPoint Appliance.
Run the Command: Execute the set_user name=admin password= command to initiate the password reset process.
Set New Password: Follow the prompts to set a new password for the admin user.
This process is used when the admin password has been lost and needs to be reset. It is important to follow the correct syntax and procedure to ensure the security and integrity of the system1.
Question 34
A company decided to change their VNX environment from MirrorView to RecoverPoint with VNX(SE) as a disaster recovery solution. They initially planned to purchase four RPAs at each site to replication between Sites A and B. However, to ensure the company uses their large server inventory, management plans to change from physical RPAs to vRPAs.
What effect do their plans have on the license procurement?
When changing from physical RPAs to vRPAs in a RecoverPoint with VNX(SE) environment, the licensing remains the same and no additional action is required. The existing licenses can be applied to the virtual RPAs without the need for new licenses.
Dell RecoverPoint for Virtual Machines 6.0.1 vSphere HTML5 Plugin Administrator's Guide, Chapter on licensing and virtual RPA deployment.
Question 35
An administrator ran the capture load command on a RecoverPoint cluster during a high-load issue. However, the administrator forgot to capture the output. Where can the RecoverPoint Cluster Load report be located?
Access the Cluster Management Interface: Use a web browser to navigate to the RecoverPoint Cluster Management IP address.
Navigate to the Load Statistics: Append /info/long_term_statistics to the Cluster Management IP in the browser's address bar.
View the Report: The RecoverPoint Cluster Load report can be viewed on this page, which provides long-term statistics including load information.
This method allows administrators to retrieve historical load data even if they did not capture the output at the time the capture load command was run1.
Question 36
What is the maximum number of copies that RecoverPoint can maintain?
Unlock Premium Member
Question 37
In order to perform dynamic resizing of a replication set, what is a requirement?
Question 38
A RecoverPoint administrator wants to add volumes from an unlicensed array to a RecoverPoint/EX cluster. Which supported RecoverPoint volume type(s) addresses the administrator's requirement?
Question 39
A Consistency Group contains a production and a remote copy. Both are provisioned from XtremlO arrays. Where are the snapshots that represent the point-in-time images kept during normal replication?
Question 40
Which command should be used to verify if the VMAX LUNs to be used with RecoverPoint are tagged?
Related questions
Export
If you didn't receive an email within 5 minutes, you should submit a support request to [email protected].
|
BASIC - 1 Month
$
10
Full latest questions
No CAPTCHA
New Updates
Export to VPLUS
Export to PDF - All questions
Team support
|
PLUS - 2 Months
$
15
Full latest questions
No CAPTCHA
New Updates
Export to VPLUS
Export to PDF - All questions
Team support
|
PRO - 6 Months
$
40
Full latest questions
No CAPTCHA
New Updates
Export to VPLUS
Export to PDF - All questions
Team support
|
Full latest questions
No CAPTCHA
New Updates
Export to VPLUS
Export to PDF - All questions
Team support
Full latest questions
No CAPTCHA
New Updates
Export to VPLUS
Export to PDF - All questions
Team support
Full latest questions
No CAPTCHA
New Updates
Export to VPLUS
Export to PDF - All questions
Team support
Selling illegal goods, money scams etc.
Serious attack on a group.
Harassing an individual (including doxing)
Threatening or glorifying violence or serious harm, including self-harm
Nudity/Sexual content
Sexually explicit or suggestive imagery or writing involving minors
Sexually explicit or suggestive imagery or writing involving non-consenting adults or non-humans
Reusing content without attribution (link and blockquotes)
Not in English or has very bad formatting, grammar, and spelling
Author's credential is offensive, spam, or impersonation
Ex. Illegal content, incomplete question...
Question