Home / Huawei / H12-891

Huawei H12-891 Practice Test - Questions Answers, Page 54

Question list

List of questions

Question 531

(0)

Each DD message has a sequence number for data confirmation, and a DD sequence number is 2 bytes long

Question 532

(0)

SNMPv3 defines which security features

Question 533

(0)

Which timer for spanning tree protocol dictates how often to see the root bridge send configuration BPDUs?

Question 534

(0)

Users hope to be able to make the router forward and select messages according to their own defined policies on the basis of traditional route forwarding, and can adopt policy routing, and the follo

Question 535

(0)

The command ip as-path-fiter as-path-fiter-number (denylpermit) regular-expression to configure aspath- ilter, in this command , multiple sentences can form an as-path-filter statement, what is the

Question 536

(0)

The following description of the characteristics of Huawei device Eth-trunk link aggregation is correct?

Question 537

(0)

The following description of the GVRP interface registration mode in Huawei switches is correct?

Question 538

(0)

When troubleshooting a local area network, you notice a large number of frame alignment errors, FCS errors and LAG conflicts, and the possible cause of these problems is ?

Question 539

(0)

Protocols with TCP ports 443, 179, 137, 110, and 23 are, in order: radio

Question 540

(0)

What designs in the router can improve the reliability of the router?

Question 531

Each DD message has a sequence number for data confirmation, and a DD sequence number is 2 bytes long

True

False

Show Answer Comment (0)

Question 532

SNMPv3 defines which security features

Privacy

Authentication

Domain checking

Accounting

Show Answer Comment (0)

Question 533

Which timer for spanning tree protocol dictates how often to see the root bridge send configuration BPDUs?

forwarding delay timer

STP timer

HOLD timer

Maxage timer

Hello timer

Show Answer Comment (0)

Users hope to be able to make the router forward and select messages according to their own defined policies on the basis of traditional route forwarding, and can adopt policy routing, and the following description of policy routing is incorrect

Policy Routing can set the next hop IP address

Policy Routing cannot be set in the next statement DSCP

Policy Routing cannot be used to set IP precedence

Policy-based routing can be used to match message lengths

Show Answer Comment (0)

Question 535

The command ip as-path-fiter as-path-fiter-number (denylpermit) regular-expression to configure aspath- ilter, in this command , multiple sentences can form an as-path-filter statement, what is the relationship between so many statements?

Routes match in order When a route matches to a clause, the relationship between

and is no longer matched downwards

or relationships

Routes match in order and routes need to match all sub-directions

Show Answer Comment (0)

Question 536

The following description of the characteristics of Huawei device Eth-trunk link aggregation is correct?

Link aggregation enables load balancing based on data TCP or UDP ports

Link aggregation cannot be deployed across devices

Link aggregation can be applied to Both Layer 2 and Layer 3 devices

Link aggregation can only be applied to Layer 2 devices.

Show Answer Comment (0)

Question 537

The following description of the GVRP interface registration mode in Huawei switches is correct?

When fixed registration mode is selected, the interface cannot propagate dynamic VLANs

When the normal registration mode is selected, allow the interface to dynamically register and unregister the VLAN. Logout here includes deleting dynamically learned VLANs and VLANs created natively by the administrator

When the interface layer two operating mode must be hybird

GVRP when the register mode with forbidden is selected, there are four types of interface registration mode

Show Answer Comment (0)

Question 538

When troubleshooting a local area network, you notice a large number of frame alignment errors, FCS errors and LAG conflicts, and the possible cause of these problems is ?

Switches and terminals are interconnected over 10/100/1000base-T Ethernet links, and switches and terminals operate in half-duplex mode

There is a mode mismatch on the 1000base-LX/LH link

The operating mode does not match

on a 10/1000/1000base-T Ether link This type of error occurs in most environments

Show Answer Comment (0)