Home / Huawei / H12-891

Huawei H12-891 Practice Test - Questions Answers, Page 61

Question list

List of questions

Question 601

(0)

OSPFV is the GP running on the P4 network) OSPF3 is the KGP running on the IP6 network. OsPFV works the same basic way as OSPF2, such as elections for DR and BDR. As shown in the figure, an engineer

Question 602

(0)

View the IGMP configuration of the interface on the router RTA as follows, and the information about the operation of the RTA is incorrect

Question 603

(0)

Based on the configuration shown in the figure below, it can be known that R4 has () interfaces advertised into IS-IS?

Question 604

(0)

As shown in the figure, all routers run OSPF, which is correct in the following statement:

Question 605

(0)

R3 is not established with the RI's IS-IS neighbor, and according to the information in this figure, the possible cause is ?

Question 606

(0)

As shown in the figure, an engineer uses four routers to test the interoperability of branch networks, where R1, R2, and R3 in branch 1 deploy OSPF Network interoperability is implemented, and R, R3

Question 607

(0)

A campus deploys OSPF to achieve network interoperability, and an engineer configures R2 as shown in the figure, then the following description of the LSA in the OSPF network is wrong

Question 608

(0)

As shown in the figure, PC1 and PC2 are hosts that belong to the same network segment, below about between PC1 and PC2 What are the correct descriptions of IPv6 neighbor states?

Question 609

(0)

As shown in the figure, the overload bit of ISIS is set in the configuration of router R3, and the following statement is correct A

Question 610

(0)

The network administrator defines a traffic policing policy as follows:

Question 601

OSPFV is the GP running on the P4 network) OSPF3 is the KGP running on the IP6 network. OsPFV works the same basic way as OSPF2, such as elections for DR and BDR. As shown in the figure, an engineer uses three routers for IP6 service testing, and he wants to interconnect the IPv6 network by running OSPFv3 Which of the following statements is correct regarding the election of the network DR?

After the network converges, R1 is DR

After the network converges, the engineer modifies the priority of R1 to 100, the priority of R2 to 10, and R3 to the default value. When the network converges again, Rl is DR and R2 is BDR

After the network converges, the broadcast link adds a device, R4, with a priority of 150 When the network converges again, R4 is DR

After the network converges, R1 is powered off and restarted, and when the network converges again, R3 is DR

Show Answer Comment (0)

Question 602

View the IGMP configuration of the interface on the router RTA as follows, and the information about the operation of the RTA is incorrect

The packet interval for a particular group query is 60 seconds

The interface IP address is 1921681.1

The maximum response time for query messages is 10 seconds

The IGMP protocol version is 2

Show Answer Comment (0)

Question 603

Based on the configuration shown in the figure below, it can be known that R4 has () interfaces advertised into IS-IS?

Show Answer Comment (0)

Question 604

As shown in the figure, all routers run OSPF, which is correct in the following statement:

Both R2 and Zone 0 generate Router LSA

R2 generates Router LSA only in Zone 0

R2 forwards the R1-generated Router LSA to R3

R2 Forwards the R3-generated Router LSA to R1

Show Answer Comment (0)

Question 605

R3 is not established with the RI's IS-IS neighbor, and according to the information in this figure, the possible cause is ?

R3 duplicates the System ID of R1

R3 does not match the IS-Level of R1

R3 and R1 interconnection ports circuit-type do not match the lH authentication of

R3 and R1

Show Answer Comment (0)

Question 606

As shown in the figure, an engineer uses four routers to test the interoperability of branch networks, where R1, R2, and R3 in branch 1 deploy OSPF Network interoperability is implemented, and R, R3, R4 in Branch 2 is deployed is-IS to achieve network interoperability. Now that the engineer wants to implement R1 access to R4's loopback address, which of the following actions will meet this requirement?

No configuration is required

Publish default routes only in the OSPF process for R2

In the OSPF process of R2 and the IS-IS process, the default routes are published separately

Publish the default route only in the IS-IS process of R2

Show Answer Comment (0)

Question 607

A campus deploys OSPF to achieve network interoperability, and an engineer configures R2 as shown in the figure, then the following description of the LSA in the OSPF network is wrong

There is no Type3 LsA flooding within Areal

There is no Type3 LSA flooding in Area2

There is Type5 LSA flooding within Areal

Area2 contains Type5 LSA generic adverb

Show Answer Comment (0)

Question 608

As shown in the figure, PC1 and PC2 are hosts that belong to the same network segment, below about between PC1 and PC2 What are the correct descriptions of IPv6 neighbor states?

If the MAC address information of PC2 can be queried on PC1, the neighbor relationship may be Stale

If pc2's MAC address information can be queried on PC1, the neighbor relationship may be Probe

There are five possible neighbor states between PC1 and PC2: Incomplete, Reachable, and Stale , Delay, Probe

If the MAC address information of PC2 can be queried on PC1, the neighbor relationship must be Reachable

Show Answer Comment (0)

Question 609

As shown in the figure, the overload bit of ISIS is set in the configuration of router R3, and the following statement is correct

R3's direct route will be ignored by R1 and R2 because of the setting of the overload bit .

When the router runs out of memory, the system automatically sets the overload flag bit in the sent LSP packets. Irrelevant to whether the user has a set-overload command configured.

Routes introduced by C. R3 through import-route will not be published. The LSP of

R3 will not be able to spread to R1 and R2

R3 initiates the load state, and R1 and RZ will not calculate the LSP of R3 cattle in the SP tree.

Show Answer Comment (0)