ExamGecko
Home Home / Huawei / H35-260

Huawei H35-260 Practice Test - Questions Answers, Page 34

Question list
Search
Search

Which of the following descriptions about bit errors in the SDH network is wrong?

A.
B1, B2, B3 can only detect the even number of errors in a block, and the odd number of errors cannot be detected
A.
B1, B2, B3 can only detect the even number of errors in a block, and the odd number of errors cannot be detected
Answers
B.
B1, B2, B3 can only detect the odd number of errors in a block, and the even number of errors cannot be detected
B.
B1, B2, B3 can only detect the odd number of errors in a block, and the even number of errors cannot be detected
Answers
C.
Through B1, B2, B3, the bit errors of the regeneration section, multiplex section and high-order channel can be detected respectively
C.
Through B1, B2, B3, the bit errors of the regeneration section, multiplex section and high-order channel can be detected respectively
Answers
D.
Bit error means that after receiving, judging, and regenerating, some bits in the digital code stream have errors.
D.
Bit error means that after receiving, judging, and regenerating, some bits in the digital code stream have errors.
Answers
Suggested answer: A

When the switch is working, the device forwards data according to the MAC address forwarding table. Which of the following descriptions is correct?

A.
The destination address of the packet is a unicast MAC address, but there is no corresponding entry in the MAC address table, the packet is discarded
A.
The destination address of the packet is a unicast MAC address, but there is no corresponding entry in the MAC address table, the packet is discarded
Answers
B.
If the MAC address entry of the device reaches the upper specification limit of the device, the device cannot learn a new MAC address entry, and the data packet is discarded.
B.
If the MAC address entry of the device reaches the upper specification limit of the device, the device cannot learn a new MAC address entry, and the data packet is discarded.
Answers
C.
If the destination MAC address of the packet is the broadcast MAC address, it will be flooded to all ports including the source port.
C.
If the destination MAC address of the packet is the broadcast MAC address, it will be flooded to all ports including the source port.
Answers
D.
The destination address of the message is a unicast MAC address, then look up the MAC address table, and if found, forward the frame to the corresponding port (excluding the source port)
D.
The destination address of the message is a unicast MAC address, then look up the MAC address table, and if found, forward the frame to the corresponding port (excluding the source port)
Answers
Suggested answer: D

Which of the following LSRs are passed by an LSP?

A.
Egress
A.
Egress
Answers
B.
Lable
B.
Lable
Answers
C.
Ingress
C.
Ingress
Answers
D.
Transit
D.
Transit
Answers
Suggested answer: A, C, D

When PTN carries LTE services, it forwards packets based on MPLS label switching. In the MPLS label, which identification field can be used as a PTN to distinguish the label at the bottom of the stack?

A.
Label ID
A.
Label ID
Answers
B.
BS
B.
BS
Answers
C.
EXP
C.
EXP
Answers
D.
TTL
D.
TTL
Answers
Suggested answer: D

When TCAT adds points, it recalculates the Tunnel and distributes the configuration. Which of the following information is being modified?

A.
The name of the Tunnel
A.
The name of the Tunnel
Answers
B.
Tunnel jump information
B.
Tunnel jump information
Answers
C.
Tunnel the sink node of
C.
Tunnel the sink node of
Answers
D.
The source node of the tunnel
D.
The source node of the tunnel
Answers
Suggested answer: B

Which of the following ways does the Inspector inspection tool support adding network elements?

A.
Automatically discover network elements
A.
Automatically discover network elements
Answers
B.
Manually add network elements
B.
Manually add network elements
Answers
C.
NEs actively report
C.
NEs actively report
Answers
D.
Import network elements in batches
D.
Import network elements in batches
Answers
Suggested answer: B, D

Which of the following are the possible reasons for the disconnection of network elements?

A.
All the optical paths to the NE are faulty
A.
All the optical paths to the NE are faulty
Answers
B.
Failure of the main control board of the network element
B.
Failure of the main control board of the network element
Answers
C.
The gateway network element connection is interrupted
C.
The gateway network element connection is interrupted
Answers
D.
The device is running
D.
The device is running
Answers
Suggested answer: A, B, C

The NCE network management supports a variety of external interfaces. Which of the following interfaces can be used when connecting with the network management equipment of other manufacturers?

A.
CORBA
A.
CORBA
Answers
B.
MML
B.
MML
Answers
C.
TL1
C.
TL1
Answers
D.
QX
D.
QX
Answers
Suggested answer: A

Explanation:


Total 338 questions
Go to page: of 34