Refer to the exhibit. The administrator expects the AP to connect to a cluster, but the AP fails to connect. The administrator examines the configuration of an AP from apboot mode shown in the exhibit. What can the administrator determine about the configuration of the AP?

The AP is configured to terminate on a Mobility Controller in a cluster.

The AP is configured to terminate on a non-cluster Mobility Controller.

The AP is configured as a RAP to terminate on a stand-alone controller.

The AP is configured as a RAP to terminate on a Mobility Master.

The AP is configured to terminate on a Mobility Controller in a cluster.

Refer to the exhibit. An administrator implements the MultiZone feature. The administrator sets up five zones as shown in the exhibit.-Zone A has six controllers that form a cluster.-Zone B has three controllers that from a cluster.-Zones C, D, and E have a single standalone controller each.A total of 13 VAPs are created across the five zones. A zone needs to accept RAP connections form branch offices. All zones have the same AP Group name. One of the zones will not accept connections from the MultiZone APs.Which could be a cause of this problem?

RAPs are used in the configuration.

The number of zones exceeds the maximum limit of four zones.

AP Group names are different for each zone.

The number of VAPs exceeds the maximum limit of 12 VAPs.

An administrator creates service-based policies for AirGroup on the Mobility Master (MM). The administrator can define location-based policy limits based on which information?

AP names, AP groups, and AP Fully Qualified Location Names (FQLNs)

AP names, AP groups, controller names, and controller groups

AP Fully Qualified Location Names (FQLNs) and controller Fully Qualified Domain Names (FQDNs)

AP names, AP groups, and AP Fully Qualified Location Names (FQLNs)

Controller names, controller groups, and controller Fully Qualified Domain Names (FQDNs)

A branch office location has two buildings: an office and a small warehouse that are within 20 meters of each other. A RAP at the branch office provides connectivity to the corporate office network. This RAP is also configured as a RemoteMesh Portal (RMP).Which solution should the administrator implement to provide connectivity between the office and small warehouse buildings at the branch office location?

Deploy a Mesh Point AP in the warehouse building to connect to the Remote Mesh Portal in the office building.

Deploy a Remote Mesh Portal in the warehouse building to connect to the Remote Mesh Portal in the office building.

Deploy a Remote Mesh Point AP in the warehouse building to connect to the Remote Mesh Portal in the office building.

Deploy an ArubaOS-Switch in the warehouse building with tunneled node to connect to the Remote Mesh Portal in the office building.

Deploy a Mesh Point AP in the warehouse building to connect to the Remote Mesh Portal in the office building.

An administrator uses a ClearPass server to perform user authentication and download the role configuration that should be applied to the user's session. The server is associated to an AAA profile of a VAP. However, when a user connects to the SSID of the VAP, they are assigned the default role.What must the administrator do to ensure that the role is downloaded and used?

Enable download role for CPPM in the VAP's WLAN profile.

Enable server derivation in the ClearPass' RADIUS configuration.

Enable server derivation in the server group.

Enable server derivation in the AAA Server Group.

An administrator deploys an Aruba wireless solution comprised of:-a pair of Mobility Masters (MMs)-multiple Mobility Controllers (MCs) and virtual Mobility Controllers (VMCs) -an AirWave server -a ClearPass server The Aruba Mobility solution runs ArubaOS 8.X.Which component in this environment globally defines and deploys VLANs for wireless users?

Mobility Controller or Virtual Mobility Controller

A cluster has two Aruba 7240 Mobility Controllers (MCs) and two Aruba 7220 Mobility Controllers (MCs). How is the cluster leader elected if all controllers have the default priority?

The 7240 controller with the highest MAC address is elected.

The controller with the highest IP address is elected.

The controller with the highest MAC address is elected.

The 7240 controller with the lowest IP address is elected.

An administrator configures AirGroup policies to define which Apple services are visible and available to wireless users in a campus WLAN. However, the policies are not being enforced.Where must the administrator enable the AirGroup functionality on the Mobility Master (MM) so that the policies will be in effect?

At the global Managed Network hierarchy

At the Mobility Master hierarchy

At the controller level in the Managed Network hierarchy

At the Access Points level in the Managed Network hierarchy

At the global Managed Network hierarchy

Refer to the exhibit. An administrator wants to centralize administrative access to the Aruba Mobility Controllers (MC) and Mobility Master (MM). ClearPass is set up and the preferred authentication protocols is TACACS+. Where should the administrator perform this configuration in the MM hierarchy shown in the exhibit?

At both the Mobility Master and Managed Network levels

An administrator inherits an Aruba Mobility Controller (MC) that has an unknown username and password. Which credentials should the administrator enter to reset the administrative access?

Username: password; Password: forgetme!

Username: backdoor; Password: @ruba

Username: admin; Password: admin

Username: password; Password: forgetme!

Username: Aruba; Password: Reset!

An administrator configures the MultiZone feature for a company network, where a mobility cluster is the primary zone and a standalone controller in the company's DMZ represents a secondary data zone. The administrator configures two AP Groups and respective VAPs for the zones on the Mobility Master (MM) in the primary zone. When the APs boot up and establish connections to both zones, the administrator notices that no data connections are established to the data zone.What must the administrator do to fix this problem?

Configure the same AP Group in the data zone as it is in the primary zone, and configure the VAPs in the data zone.

Configure the same AP Groups and VAPs on the standalone controller, and associate the MultiZone APs to both groups.

Configure the same AP Group in the data zone as it is in the primary zone, and configure the VAPs in the data zone.

Have the MultiZone APs initially boot from the standalone controller in the data zone.

Create different AP groups and VAPs on the Mobility Master and standalone controllers, and associate the MultiZone APs to both groups.

An administrator currently manages an L2 cluster with Aruba Mobility Controllers (MCs) that run ArubaOS 8.x. What happens when the administrator enables AP load balancing?

AP load balancing occurs when the rebalance and unbalance thresholds are met.

Users must re-authenticate if they are moved from one controller to another because load balancing is performed.

Balancing of users is based on a hash of their IP address.

AP load balancing is triggered based on the amount of user traffic that users generate.

An administrator implements clustering on Aruba Mobility Controllers (MCs) that run ArubaOS 8.x.An AP is connected to a cluster member. The administrator accidentally powers off the AP.How does the AP determine that it should failover to an alternate controller in the cluster?

The Standby AAC notifies the AP.

The Mobility Master notifies the AP.

The cluster leader notifies the AP.

The Standby AAC notifies the AP.

An administrator creates a cluster of four Mobility Controllers (MCs). When the administrator verifies the cluster operation, the administrator notices that it is operating as an L3-connected cluster.What should the administrator do to ensure that the cluster operates as an L2-connected cluster?(Choose two.)

Exclude all VLANs that are not trunked to each Mobility Controller.

Ensure that the controller IP addresses are in the same subnet.

Include all IP addresses in the same subnets shared by the Mobility Controllers.

Exclude all VLANs that are not trunked to each Mobility Controller.

Verify VLAN configuration on the switch trunks that interconnects the Mobility Controllers.

Configure a separate VRRP group for each cluster member.

Ensure that the controller IP addresses are in the same subnet.

An administrator has ArubaOS-Switches that support tunneled node. The administrator wants to tunnel all user traffic from the Ethernet ports on the switches, and have the controllers authenticate the user traffic and apply the appropriate user role.Which implementation meets these requirements?

Per-port tunneled node with the controllers configured for standalone mode

Role-based tunneled node with the controllers configured for standalone mode

Role-based tunneled node with the controllers configured in a cluster

Per-port tunneled node with the controllers configured for standalone mode

Per-port tunneled node with the controllers configured in a cluster

What are the responsibilities of a cluster leader in a cluster of Aruba Mobility Controllers (MCs)?(Choose two.)

To create a table to determine how a wireless client maps to a cluster member

To automatically load balance clients if the load across cluster members changes

To identify primary and secondary Mobility Controllers for APs

To create a table to determine how a wireless client maps to a cluster member

To identify a backup cluster leader for redundancy

To manage the configuration of cluster members

To automatically load balance clients if the load across cluster members changes

An administrator wants to implement a Live Upgrade (in-service upgrade) of a cluster in an Aruba wireless solution. Which ArubaOS feature does the Mobility Master (MM) use to ensure RF redundancy, so that when one or more APs are rebooted there is no loss of wireless coverage for users?

Mobility Controller load balancing

Which ArubaOS CLI command can an administrator execute to determine if AP load balancing is enabled in a cluster?

show lc-cluster group-membership

What must an administrator configure in order for the ClearPass server to execute a RADIUS Change of Authorization (CoA) to Aruba Mobility Controllers (MCs) in a cluster?

Active and Standby AAC with clustering

IPSec High Availability (HA) between two cluster members

Primary and backup LMS IP addresses

An administrator configures a network scan set in AirWare to scan a subnet to discover new switches. The scan completes and AirWave successfully uses the SNMP credentials to validate SNMP access. However, SSH access fails and the administrator must manually configure the SSH credentials used for all of these devices.To prevent this problem in the future, what should the administrator complete prior to running the network scan?

Define the SSH communication parameters for the Default Credentials under Device Setup section.

Define the SSH communication parameters under the Group's Manage section.

Define a scan credentials set that includes the SSH communication parameters.

Define the SSH communication parameters under the AP/Device's Manage section.

Define the SSH communication parameters for the Default Credentials under Device Setup section.

An administrator needs to apply a patch to an Aruba environment to implement improvements for AirMatch. What is the Aruba recommended approach for this process without a reboot?

Upgrade the AirMatch Loadable Service Module (LSM) on the Mobility Master.

Upgrade the AirMatch Loadable Service Module (LSM) on each Mobility Controller.

Upgrade the AirMatch Loadable Service Module (LSM) on the Mobility Master.

Upgrade the ArubaOS by the use of Live Upgrades (in-service upgrades).

Create controller partitions to minimize downtime.

An administrator implements a per-port tunneled node configuration for an Aruba Mobility Controller (MC) that runs ArubaOS 8.x. The controller performs both MAC and 802.1X authentication.What must the administrator specify on the controller to allow for 802.1X authentication to succeed?

Enable L2 Authentication Fail Through in the AAA profile.

Define External RADIUS servers in the AAA profile.

Enable L2 Authentication Fail Through in the AAA profile.

Define MAC addresses in the local database for the 802.1X users.

Enable server roles in the AAA profile.

Refer to the exhibit. What can the determined from the command shown in the exhibit?

VRRP is used for Mobility Master redundancy.

All the controllers run in standalone mode.

VRRP is used for Mobility Master redundancy.

All the controllers run in a cluster.

HP HPE6-A71 Practice Test 2 - Free Online Exam Questions 41-80

Refer to the exhibit.

HP HPE6-A71 image Question 41 14351 09162024180649000000

A user uses Microsoft Windows for a wireless session. Based on the output shown in the exhibit for the selected Aruba AP, what is the possible problem with this user's wireless session?

Become a Premium Member for full access

Unlock Premium Member

HP HPE6-A71 Practice Test 2

Question

HP HPE6-A71 Practice Tests

Practice Tests