A network administrator is troubleshooting a client's device that cannot connect to the network. A physical inspection of the switch shows the RJ45 is connected. The NIC shows no activity lights. The network administrator moves the device to another location and connects to the network without issues. Which Of the following tools would be the BEST option for the network administrator to use to further troubleshoot?

Optical time-domain reflectometer

SIMULATIONA network technician replaced a switch and needs to reconfigure it to allow the connected devices to connect to the correct networks.INSTRUCTIONSClick on the appropriate port(s) on Switch 1 and Switch 3 to verify or reconfigure the correct settings:•bullet Ensure each device accesses only its correctly associated network•bullet Disable all unused switch ports•bullet Require fault-tolerant connections between the switches•bullet Only make necessary changes to complete the above requirementsIf at any time you would like to bring back the initial state of the simulation, please click the Reset All button.

See the explanation for this solution

A network technician receives a report from the server team that a server's network connection is not working correctly. The server team confirms the server is operating correctly except for the network connection. The technician checks the switchport connected to the server and reviews the following data; Which of the following should the network technician perform to correct the issue?

Replace the Cat 5 patch cable with a Cat 6 cable

Install a crossover cable between the server and the switch

Reset the switchport configuration.

Use NetFlow data from the switch to isolate the issue.

Disable MDIX on the switchport and reboot the server.

A network technician is investigating a trouble ticket for a user who does not have network connectivity. All patch cables between the wall jacks and computers in the building were upgraded over the weekend from Cat 5 to Cat 6. The newly installed cable is crimped with a TIA/EIA 568A on one end and a TIA/EIA 568B on the other end.Which of the following should the technician do to MOST likely fix the issue?

Crimp the cable as a straight-through cable.

Ensure the switchport has PoE enabled.

Crimp the cable as a straight-through cable.

Ensure the switchport has STP enabled.

Crimp the cable as a rollover cable.

A network administrator is implementing process changes based on recommendations following a recent penetration test. The testers used a method to gain access to the network that involved exploiting a publicly available and fixed remote code execution vulnerability in the VPN appliance.Which of the following should the administrator do to BEST prevent this from happening again?

Routinely upgrade all network equipment firmware.

Change default passwords on internet-facing hardware.

Implement robust ACLs with explicit deny-all entries.

Create private VLANs for management plane traffic.

Routinely upgrade all network equipment firmware.

A company is undergoing expansion but does not have sufficient rack space in its data center. Which of the following would be BEST to allow the company tohost its new equipment without a major investment in facilities?

Using available rack space in branch offices

Reorganizing the network rack and installing top-of-rack switching

A company, which is located in a coastal town, retrofitted an office building for a new data center.The underground fiber optics were brought in and connected to the switches in the basement network MDF. A server data center was built on the fifth floor with the two rooms vertically connected by fiber optics. Which of the following types of environmental sensors is MOST needed?

Water sensor in the network MDF

Temperature sensor in the network MDF

Water sensor in the network MDF

Temperature sensor in the data center

Water sensor in the data center

A public, wireless ISP mounts its access points on top of traffic signal poles. Fiber-optic cables are installed from a fiber switch through the ground and up the pole to a fiber-copper media converter, and then connected to the AP. In one location, the switchport is showing sporadic link loss to the attached AP. A similar link loss is not seen at the AP interface. The fiber-optic cable is moved to another unused switchport with a similar result. Which of the following steps should the assigned technician complete NEXT?

Clean the fiber-optic cable ends.

Disable and enable the switchport.

Clean the fiber-optic cable ends.

CompTIA N10-008 Practice Test 13 - Free Online Exam Questions 481-520

A store owner would like to have secure wireless access available for both business equipment and patron use. Which of the following features should be configured to allow different wireless access through the same equipment?

Become a Premium Member for full access

Unlock Premium Member

CompTIA N10-008 Practice Test 13

Question

CompTIA N10-008 Practice Tests

Practice Tests