A new Nutanix customer suspects that network traffic is going over the 1G interfaces instead of the 10G interfaces.How should a consultant confirm that the traffic is only traversing the 10G interfaces?

Run the allssh manage_ovs show interfaces command.

Look in Prism Element under Network.

Run the allssh manage_ovs show interfaces command.

Run the iconfig command on the CLI of each CVM.

Run the allssh manage ovs show uplinks command.

For a new AHV cluster installation, a customer has 20 NX-8155 nodes with quad port NICs. The customer wants to meet the following guidelines:Take advantage of all available 10G linksAchieve maximum throughput per VMUse of redundant ToR switchesFastest reconvergence during link failureHow should the load balancing be configured on the host?

Use CLI to configure Balance-TCP on bridge bro.

In Prism Element, update the virtual switch uplink configuration to Active-Active with MAC pinning.

In Prism Element, update the virtual switch uplink configuration to Active-Active.

Use CLI to add the interfaces to bridge bro on all hosts.

Use CLI to configure Balance-TCP on bridge bro.

A consultant is deploying a new Nutanix cluster. The nodes have the following network interfaces.2x 10G NICS2x 25G NICSThe consultant is using the default virtual switch configurations for AHV. After creating 10 VMs, the consultant observes inconsistent network speeds from the VMs on the AHV host.What should the consultant do to resolve this issue?

Configure all network interfaces with LACP on the same virtual switch.

Configure load balancing on the virtual switch for both 106 and 25G interfaces.

Configure a separate virtual switch with 10G NICs on vs o and 256 NICs on vs.

Configure Active/Backup for both the 10G and 25G interfaces.

Configure all network interfaces with LACP on the same virtual switch.

A consultant discovers that while the Foundation VM and the consultant's laptop are able to ping each other nodes are rea discovered while trying to run Foundation on the customer's network.What should the consultant do to resolve the issue?

Enable IPv6 and multicast on the switch.

Connect to same switch as the cluster and ping.

Install Java on the Foundation VM.

Enable IPv6 and multicast on the switch.

Enable IPv6 and multicast on the laptop.

A customer has HE servers with DiscoverOS and wants to install a Nutanix cluster.Which method should a consultant use to meet the requirements?

Create the cluster using CVM Foundation.

Create the cluster using Crash cart.

A consultant needs to upgrade the ESXi hosts on a Nutanix cluster from version 6.7 to 7.0. vSphere DRS and wMoton are working properly. The consultant needs to use One-Click Upgrade.Which setting should be verified by the consultant?

vSphere DRS Automation level is set to Conservative.

DRS automation level on all CVMs is disabled.

A customer has an ESXi cluster with two 10GbE NICs on each node and the following requirements.Solution must follow Nutanix Best PracticesNetwork configuration should be redundantA vSphere Distributed Switch will be utilizedWhich load balancing configuration should be used?

Route based on originating port ID

Route based on physical NIC load

Which two files should be downloaded to deploy Foundation VM on VMware ESXI or AHV Hypervisors? (Choose two.)

foundation_VM-version-disk-0.geow2

Which two files should be downloaded to deploy Foundation VM on VMware ESXI or AHV Hypervisors? (Choose two.)

foundation_VM-version-disk-0.geow2

A consultant is unable to ping the CVM from the hypervisor using the external interface. The customer's network is configured with the 10.3.12.0/24 subnet without VLAN tagging. The CVM and hypervisor are using the same address space.What is causing this issue?

The default gateway is incorrect.

The 1GbE and 10GbE NICs have not been separated.

The default gateway is incorrect.

The switch is trunked without a native VLAN.

The CVM/hypervisor only communicates over 192.168.5.0/24.

A consultant is setting up Prism Central to manage multiple Nutanix clusters. The customer requires til redundancy and tre aby to manage up to 12,500 VMs.Which deployment option should the consultant use to meet the requirements?

Prism Central Scale-out deployment

Maximum CPU and memory allowed for the server hosting the Prism Central VM

Prism Central Scale-out deployment

Large Prism Central VM with the maximum CPU and memory allowed

A consultant deploys a Nutanix cluster with AOS and ESXi. The cluster is managed by a vCenter server.After installation, what should the consultant do to ensure the cluster will support network segmentation?

Connect both CVM eth0 and eth2 interfaces to the assigned portgroups.

Connect both CVM eth0 and eth2 interfaces to vSwitchNutanix.

Manually assign an IP address to the CVM eth2 interface.

Connect both CVM eth0 and eth2 interfaces to the assigned portgroups.

Add another vSwitch to the cluster.

Nutanix NCS-Core Practice Test 8 - Free Online Exam Prep & Questions

Refer to the exhibit.

Nutanix NCS-Core image Question 281 82251 09232024013105000000

Which IP addresses can be configured for the Foundation VM and Consultant Laptop?

Become a Premium Member for full access

Unlock Premium Member

Nutanix NCS-Core Practice Test 8

Question

Nutanix NCS-Core Practice Tests

Practice Tests