Home / Nutanix / NCSC-Level-1

Nutanix NCSC-Level-1 Practice Test - Questions Answers, Page 4

Question list

List of questions

Question 31

(0)

A customer needs to meet the following requirements for their business critical application: * SQL Servers must be on specific hosts to lower licensing costs. * Oracle RAC servers must be on separ

Question 32

(0)

For a new AHV cluster installation, a customer has 20 NX-8155-G6 nodes with quad port SFP NICs. The customer wants to meet the following guidelines: * Take advantage of all available 10GbE links

Question 33

(0)

Where in the Support Portal is the Best Practices guide for vSphere Networking located?

Question 34

(0)

A consultant needs to review a customer’s switch port configuration to identify any issues. Other customer requirements are as follows: * Leverage LACP * Native VLAN will not be used * Use Multip

Question 35

(0)

Which two components must be identified to validate that software compatibility requirements are met for Nutanix Cluster Installation? (Choose two.)

Question 36

(0)

Which subnet is reserved for internal connectivity within a Nutanix Cluster?

Question 37

(0)

A consultant runs the Foundation Applet and discovers all the nodes. The consultant wants to use the latest version of Foundation for imaging for support purposes and to cover the latest hardware an

Question 38

(0)

While preparing for a new four-node cluster installation, the consultant has a Tech Review Call with the customer. The hardware is as follows: * 4 nodes in 1 Block * 8 x 10 GbE Ports * 4 x 1 GbE

Question 39

(0)

After a consultant runs Foundation, the imaging process fails. In which two locations can the consultant find the logs? (Choose two.)

Question 40

(0)

During a technical call with a customer, it is identified that this installation will be software only on Dell servers. The out-of-band management interfaces will not be given IP addresses until the

Related questions

A consultant is deploying a Nutanix cluster at a customer location. The consultant will be deploying the latest AOS along with the latest Nutanix hardware. Which three references should the consultant review prior to this installation? (Choose three.)

A consultant creates a new cluster using ESXi as the hypervisor. After creating the cluster, the consultant begins to run Life Cycle Manager (LCM) updates. During the LCM upgrade pre-checks, an error is returned. Which configuration is causing this issue?

During the Foundation imaging process, nodes are successfully imaged, but the cluster creation fails. Which log should the consultant review to determine the cause?

A consultant is using a customer’s switch for installation. Although the 10GbE ports for each of the hosts are connected to the switch, the nodes fail to be discovered. What is causing the issue?

What is the minimum number of nodes required for a Nutanix Cluster to support Replication Factor 3 (RF3) on a storage container?

A consultant creates three storage containers (container-1, container-2, container-3). The customer requires that only container-1, which will be utilized as an NFS datastore, be presented to external hosts. However, users are able to mount all three containers. What is causing this problem?

Which Nutanix feature creation is described in the Knowledge Transfer?

A consultant has deployed a Nutanix cluster with AOS 5.10.x, then discovers the customer’s environment is running on AOS 5.6.x. The consultant decides to re-image the cluster using the foundation Java applet. During the Foundation discovery, all cluster nodes display a status of Unavailable. What should the consultant do to resolve the issue?

During the Knowledge Transfer, the customer askes where to find the details about their Nutanix environment, such as IP addresses, storage containers, and configuration. Where can the consultant find this information?

A consultant configures a Nutanix cluster and integrates the hosts into vCenter using VMware best practices. The customer has requested that the Nutanix cluster only have a single datastore. Upon configuring the cluster per the customer requirements, vCenter displays an alert regarding the heartbeat datastore. The consultant adds the das.ignoreInsufficientHbDatastore value = true rule. The container can be seen from each host, but the alert remains active. What should the consultant do to resolve this issue?

Question 31

A customer needs to meet the following requirements for their business critical application:

* SQL Servers must be on specific hosts to lower licensing costs.

* Oracle RAC servers must be on separate hosts for licensing reasons

Which policy or policies should be implemented to meet these requirements?

Configure VM-VM anti-affinity policy.

Configure VM-VM affinity policy.

Configure both VM-Host and VM-VM affinity policy.

Configure VM-Host affinity policy.

Show Answer Comment (0)

Question 32

For a new AHV cluster installation, a customer has 20 NX-8155-G6 nodes with quad port SFP NICs.

The customer wants to meet the following guidelines:

* Take advantage of all available 10GbE links

* Achieve maximum throughput per VM

* Use of redundant ToR switches

* Fastest reconvergence during link failure

How should the load balancing be configured on the host?

ovs-vsctl set port br0-up bond_mode=balance-slb ovs-vsctl set port br0-up other_config:bond-rebalance-interval=30000 ovs-vsctl set port br0 tag=10

ovs-vsctl set port br0-up bond_mode=active-backup ovs-vsctl set port br0-up other_config:bond-rebalance-interval=30000

ovs-vsctl set port br0-up bond_mode=balance-slb

ovs-vsctl set port br0-up other_config:lacp-fallback-ab=true ovs-vsctl set port br0-up lacp=active ovs-vsctl set port br0-up bond_mode=balance-tcp

Show Answer Comment (0)

Question 33

Where in the Support Portal is the Best Practices guide for vSphere Networking located?

Product Notices

Solutions Documentation

Software Documentation

Knowledge Base

Show Answer Comment (0)

Question 34

A consultant needs to review a customer’s switch port configuration to identify any issues. Other customer requirements are as follows:

* Leverage LACP

* Native VLAN will not be used

* Use Multiple Upstream switches

* Use VLANs 20-25 and 30

* LACP Fallback has been Enabled

* vPC or MLAG has been configured

What must be included in a configuration in order to meet these requirements?

Native VLAN set to defaultPorts trucked to allow all necessary VLANs

Native VLAN set to defaultPorts in access mode to allow all necessary VLANs

Native VLAN set to 30Ports Trunked to allow all necessary VLANs

Native VLAN set to 30Ports in access mode to allow all necessary VLANs

Show Answer Comment (0)

Question 35

Which two components must be identified to validate that software compatibility requirements are met for Nutanix Cluster Installation? (Choose two.)

Guest OS

AOS

Firmware

Hypervisor

Show Answer Comment (0)

Question 36

Which subnet is reserved for internal connectivity within a Nutanix Cluster?

192.168.5.0/24

192.168.254.0/24

192.168.5.0/23

192.168.5.0/26

Show Answer Comment (0)

A consultant runs the Foundation Applet and discovers all the nodes. The consultant wants to use the latest version of Foundation for imaging for support purposes and to cover the latest hardware and software hypervisor support.

What should the consultant do to upgrade Foundation on a node?

Use crash cart and manually upgrade Foundation files on one node.

Use latest version of Foundation to reimage all the nodes.

Use the Foundation VM to upgrade Foundation on all nodes.

Use the Foundation Applet to upgrade Foundation on a single node.

Show Answer Comment (0)

Question 38

While preparing for a new four-node cluster installation, the consultant has a Tech Review Call with the customer. The hardware is as follows:

* 4 nodes in 1 Block

* 8 x 10 GbE Ports

* 4 x 1 GbE IPMI Ports

* Adequate Ethernet ports are available

* Ethernet cables are correct and available

* Adequate rack space is available

Which remaining item must be confirmed as available onsite?

Crash Cart

Fibre Channel switches

Redundant 208v power

Redundant 110v power

Show Answer Comment (0)

Question 39

After a consultant runs Foundation, the imaging process fails.

In which two locations can the consultant find the logs? (Choose two.)

On the Hypervisor - /home/nutanix/foundation/logs

Logs link on the Foundation Imaging Screen

On the Foundation VM - /home/nutanix/foundation/logs

On the CVM - /home/Nutanix/foundation/logs

Show Answer Comment (0)

Question 40

During a technical call with a customer, it is identified that this installation will be software only on Dell servers. The out-of-band management interfaces will not be given IP addresses until the consultant is onsite.

Which Foundation method should be used for this type of installation?

Bare metal using iDRAC MAC addresses.

Bare metal using LAN MAC addresses.

Bare metal using block serial numbers.

Bare metal using node serial numbers.

Show Answer Comment (0)

Total 78 questions